Consider the following for a single-degree-of-freedom system with m = 1. X, k = 2.5, and c = 1.8. Here, the value of X indicating of the number of your group. For example, if your group number is 15 gives X = 15, therefore the values of m = 1.15. If your group number is 9 gives X = 9, therefore the values of m = 1.9 Find; (i) Natural frequency, Wn (ii) Linear frequency, fn (iii) Critical damping constant, cc (iv) Damping ratio, 7 (v) Damped frequency, wa

Consider the following for a single-degree-of-freedom system with m = 1. X, k = 2.5, and c = 1.8. Here, the value of X indicating of the number of your group. For example, if your group number is 15 gives X = 15, therefore the values of m = 1.15. If your group number is 9 gives X = 9, therefore the values of m = 1.9 Find; (i) Natural frequency, Wn (ii) Linear frequency, fn (iii) Critical damping constant, cc (iv) Damping ratio, 7 (v) Damped frequency, wa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Using MATLAB to find the maximum.
Please Draw The Freebody On a sheet of paper Only and Solve via Handwritten Only. Here I am facing difficulty in Typed based solution. [Reaction(N) and angle(°)]
What is the return type of angles function in MATLAB ?
The raising time of a first order system is the time required to reach 90% of the final value. Select one: True False
Solve the initial value problem. y" + 4y' + 20y = 0: y(0) = 2 y (0) = - 3 %3D Chapter 6, Section 6.2, Go Tutorial Problem 12 Find Y(s). 2s + 5 Y(s): s2 + 4s + 20 2s + 5 Y(s) = s2 + 4s + 20 2s – 5 Y(s) : + 4s + 20 2 + 4s + 20 Y(s) 2s + 5
Suppose that the stiffness matrices of the above question (as shown below) are as follows: b -b a a K1 =108 x K2 =108 x -b -a a b 0.1 m 0.05 m 0.5 m 0.5 m where a= 1.8 N/m and b=2.9 N/m. Find the assembled stiffness matrix of the system using the following connectivity table. Element Node i Node j (1) 2 (2) 2 What is the summation of all terms located on the main diagonal of the assembled [a bc] stiffness matrix? (Hint: if the assembled stiffness matrix is b de then you e f need to find the value of a + d+ f). Your Answer: Answer The shape function value ) is zero at the centre of the element. O is always higher than 1. O is equal 1 at its own node and zero at other nodes. O is always less than 1.
(b) A beam is subjected to a linearly increasing distributed load. The elastic curve (deflection) is shown in the figure. The equation to find the maximum deflection is given below. Create a matlab code where you can calculate the maximum deflection (dy/dx=0) using the bisection method. Use initial guesses of 1 and 4, L= 6.46 m, E = 59000 kN/cm2, I=35000 cm4, and w0= 2.5 kN/cm. What will be the value of x (location of maximum deflection) after 14 bisection iteration? wo -23 +2L?x³ – L^x) 120EIL dy wo (-5x4 + 6L²a² – Lª) da 120EIL Choices 1.4445 O 2.6001 O4.3335 O 2.889
Please answer with The Network Simplex Method
Q3: Consider evaluation of different temperatures of solar photovoltaic/thermal system (PVT) as shown in Figure 1(a). The following set of differential equations represent energy balance equations to be solve using matrices and eigenvalues using MATLAB: dTglass = -0.75Tgtass + 0.75TpvT (1) dt - 1.187glass – 22Tpyr + 23Twax (2) dt dTwax 12Tglass + 18TpyT – 19 Twax (3) dt Where, Tgtass , TPVT, and Twax, are temperatures illustrated in Figure 1(b). At time t-0 the initial conditions are Tglass = 35 , Tpyr = 33, and Twax = 31 °C. Cold suppty In frem water Tank Glass PVT Espann Nane-PCMPVT Collector Wax Tubes Sterg Tank Nanofluid Heat Exchanger Contalner Tepe Teek oe Pump for drain
The values of p and h which renders (makes) the following set of equations dynamically and statically decoupled are, respectively. k,+k2 5 p+4 x1 = 0, X2 7 h+1 + [7h+1 J+e 5 p+4 J+e h= -0.214 and p = -1.76 h = -0.143 and p= -0.8 h = -0.281 and p= -1.2 h = -0.081 and p = -0.536
Response using matlab.
Draw the corresponding scheme and find the equation on the right. Method used and Four assumptions hA Tc.v.(t) = Taire + [Tc.v.(tt) – Tairele locp)"