Calculate (a) the mass flow rate through the system and (b) the force that is required to hold the vertical pipe configuration, as shown below, in place. The fluid in the pipe rises into the side branch tube to a height of 0.9 m. Assume that the weights of the vertical pipe configuration and the side branch attachment are negligible, the water between the jet between the orifice plate and the vena contracta weights 18N. The vena contracta is the position where all the streamline becomes parallel. 250 mm 0.9 m 225 mm 200 mm dia orifice 75 mm 150 mm dia, vena contracta

Calculate (a) the mass flow rate through the system and (b) the force that is required to hold the vertical pipe configuration, as shown below, in place. The fluid in the pipe rises into the side branch tube to a height of 0.9 m. Assume that the weights of the vertical pipe configuration and the side branch attachment are negligible, the water between the jet between the orifice plate and the vena contracta weights 18N. The vena contracta is the position where all the streamline becomes parallel. 250 mm 0.9 m 225 mm 200 mm dia orifice 75 mm 150 mm dia, vena contracta

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A very popular toy on the market several years ago was the water rocket. Water (at 10°C) was loaded into a plastic rocket and pressurized with a hand pump. The rocket was released and would travel a considerable distance in the air. Assume that a water rocket has a mass of 50g and is charged with 100g of water. The pressure inside the rocket is 100kPa gage. The exit area is one-tenth of the chamber cross-sectional area. The inside diameter of the rocket is 5cm. Assume that Bernoulli’s equation is valid for the water flow inside the rocket. Neglecting air friction calculate the maximum velocity it will attain.
A very popular toy on the market several years ago was the water rocket. Water (at 10°C) was loaded into a plastic rocket and pressurized with a hand pump. The rocket was released and would travel a considerable distance in the air. Assume that a water rocket has a mass of 50 g and is charged with 100 g of water. The pressure inside the rocket is 100 kPa gage. The exit area is one-tenth of the chamber crosssectional area. The inside diameter of the rocket is 5 cm. Assume that Bernoulli's equation is valid for the water flow inside the rocket. Neglecting air friction, calculate the maximum velocity it will attain. 5 cm PROBLEM 6.90 100 kPa
(3) The cart shown below is restrained from moving by a cable connected to a fixed wall. The tank has a circular cross section of diameter D and the flow exit has a circular cross section of diameter Do. Do not assume that H(t) is constant. The fluid has density p and the exit is open to the atmosphere. Wall H D- Do Cable Vo (1) Determine H(t) and the exit velocity Vo(t). (2) Determine the tension in the cable as a function of time Your answers should be in terms of given parameters (D, Do, p, g) о,
A hemispherical tank of diameter 4 m contains water up to a height of 2.0 m. An orifice of diameter 50 mm is provided at the bottom. Find the time required by water (i) to fall from 2.0 m to 1.0 m (ii) for completely emptying the tank. Take Cd= 0.6
Consider a length of pipe bent into a U-shape. The inside diameter of thepipe is 0.5 m. Air enters one leg of the pipe at a mean velocity of 100 m/sand exits the other leg at the same magnitude of velocity, but moving inthe opposite direction. The pressure of the flow at the inlet and exit is theambient pressure of the surroundings. Calculate the magnitude anddirection of the force exerted on the pipe by the airflow. The air densityis 1.23 kg/m3.
The Super Soaker XP30 is a marvel of hydraulic dispersion weaponry. By pumping on the handle, you charge the chamber to high pressure. The pressure is maintained until you pull the trigger at which point the water (? = 1000 kg/m3) is released at high velocity.You have charged your pressure chamber to an absolute pressure of P1 = 697500 Pascals, much higher than today's outside air pressure of 101300 Pascals. The pressure chamber is location at a height of y1 = 0.103 meters above the exit point. The exit point has a small opening with radius r = 0.0033 meters.Determine all the following:The velocity at which the water exits the Super Soaker: v2 = m/sThe mass flow rate through the exit: kg/secThe volume flow rate through the exit: m3/secNOTE: You may treat the water chamber as a "tank" and approximate the water velocity there to be zero.
The Super Soaker XP30 is a marvel of hydraulic dispersion weaponry. By pumping on the handle, you charge the chamber to high pressure. The pressure is maintained until you pull the trigger at which point the water (? = 1000 kg/m3) is released at high velocity. You have charged your pressure chamber to an absolute pressure of P1 = 675500 Pascals, much higher than today's outside air pressure of 101300 Pascals. The pressure chamber is location at a height of y1 = 0.117 meters above the exit point. The exit point has a small opening with radius r = 0.0038 meters. Determine all the following: a) The velocity at which the water exits the Super Soaker: v2 = m/s b) The mass flow rate through the exit: kg/sec c) The volume flow rate through the exit: m3/sec
A reducing bend with an inlet diameter of 200 mm and exit diameter of 150 mm bends 40 degreesupwards. The water velocity and corresponding pressure at the inlet to the band is 4, 5 m/s and 70 kParespectively. Determine the weight flow, the water flow velocity at the exit to the bend, the bend exitpressure if the friction head loss through the bend section is 2 m and the magnitude and direction ofthe resultant force flowing through the bend.
1. The figure shows a type of flushometer in which the flat vane rotates on a pivot as it deflects the fluid stream. The fluid force is balanced by means of a spring. Determine the spring force required to hold the paddle in a vertical position when water is flowing at 100 gal/min. The diameter of the pipe is 1"
A circular tank of diameter 3 m contains water up to a height of 4 m. The tank is provided with an orifice of diameter 400 mm at the bottom. Find the time taken by water : (a) to fall from 4 m to 2 m. (b) for completely emptying the tank Take Cd= 0.6
A cylindrical container with a massless and frictionless piston is filled with water up to a height h, as shown in the schematic. What mass m should be placed on the piston so that the water flow rate through the opened valve doubles? Consider that piston area A1 = 0.04 m2, valve area Az = A1/5, h = 1.2 m, Pwater = 1000 kg/m', and g = 9.80 m/s?. piston area: A m = ? valve area: A, h/5 Select one: O a. m = 0.48 kg O b. m 0.71 kg Oc. m = 0.80 kg O d. m = 0.83 kg
For the siphon shown in the figure, calculate (a) The mass flow rate of oil from the tank and (b) The pressure at point D, the height L =87 cm