c) The orifice flowmeter shown in Figure 4 is used to obtain the flowrate of oil inside aconduit. The diameter of the orice, d is one third of the pipe diameter, D with pressuredifference recorded as 25 kPa. The pipe diameter D is 6 cm, discharge coefficient Ca, is0.60, Bis the ratio of orifice diameter to pipe diameter and Oilspedific gravity, SG is 0.95.If the h is 7 cm,i.Calculațe the vollime flowrate of oil inside the conduit.ii.Determine the mass flowrate of oil inside the conduit.iii.Explain why the discharge coefficient Ca, for the orifice meter is higher comparedto the venturi and nozzle meters.D=6 cmdFigure 4

Given: d=1/3D, D=6cm, x=7cm, Pressure difference=25KPa, SG of oil=0.95, Cd=0.6 To calculate the flow…

c) The orifice flowmeter shown in Figure 4 is used to obtain the flowrate of oil inside a conduit. The diameter of the orice, d is one third of the pipe diameter, D with pressure difference recorded as 25 kPa. The pipe diameter D is 6 cm, discharge coefficient Ca, is 0.60, Bis the ratio of orifice djamererto Bipe diameter and Qilspedific gravity, SG is 0.95. If the h is 7 cm, i. Calculațe the vollime flowrate of oil inside the conduit. ii. Determine the mass flowrate of oil inside the conduit. Explain why the discharge coefficient Ca, for the orifice meter is higher compared to the venturi and nozzle meters.

c) The orifice flowmeter shown in Figure 4 is used to obtain the flowrate of oil inside a conduit. The diameter of the orice, d is one third of the pipe diameter, D with pressure difference recorded as 25 kPa. The pipe diameter D is 6 cm, discharge coefficient Ca, is 0.60, Bis the ratio of orifice djamererto Bipe diameter and Qilspedific gravity, SG is 0.95. If the h is 7 cm, i. Calculațe the vollime flowrate of oil inside the conduit. ii. Determine the mass flowrate of oil inside the conduit. Explain why the discharge coefficient Ca, for the orifice meter is higher compared to the venturi and nozzle meters.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question (2): Determine the head in the region between the two materials and the discharge in cm³/sec for the following sketch. Y Area=34 cm² K=0.03 cm/sec H Area=34 cm² K=0.004 cm/sec
A3 mm diameter tube is inserted into a fluid with Surface tension is 0.04 N/m, Density 1400 kg/m Wetting angle is 7°. Calculate the capillary rise.
PROBLEM 2 The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine (a) The velocity at section B, V (m/s) (b) The pressure at section B, ps (kPa) (с) Fмх (N) (d) FMY (N) (е) Fpx (N) (f) Fpy (N) (g) The x-component of the reaction by the bend, FRx (N) and (h) The y-component of the reaction by the bend FRY (N). de = 100 mm B- da = 150 mm 30°
A differential "U"-tube manometer containing mercury of density 13000 kg/m³ is used to measure the pressure drop along a horizontal pipe. If the fluid in the pipe is water and the manometer reading is 0.65m, what is the pressure difference between the two tapping points? Fluid density Pw A B a b datum Manometric fluid density p Hg Figure of manometer setup
The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine (a) The velocity at section B, V3 (m/s) (b) The pressure at section B, ps (kPa) (c) FMx (N) de = 100 mm B da = 150 mm 30°
Calculate the followingi. Liquid limitii. Plastic limitiii. Plasticity index
1. [Ch4 – 2] A hydraulic oil with the absolute viscosity of 0.09 N.s/m² and specific gravity of 0.9, is flowing in a 30-mm- diameter pipe at a velocity of 6 m/'s, detemine: a. The Reynolds number? Is the flow laminar or turbulent? b. The head loss due to friction in units of bars for a 100-m length of smooth pipe. 2. [Ch4 - 2] The kinematic viscosity of a hydraulic oil is 0.0001 m/s. If it is flowing in a 20-mm- diameter commercial steel pipe, find the friction factor for: a. The velocity of 5 m/s b. The velocity of 50 m/s
7) For the manometer setup shown, determine the difference in pressure between A and B. oll, s = 0.85 Water 680 mm Bo 1700 mm YWater 8) A differential manometer is attached to a pipe as shown. Calculate the pressure difference between points A and B. is h. 100 mm re A Mercury A B Oil, s = 0.90 %3!
Oil having sp. gr. of 0.9 and viscosity v 0.0002 m2/s flows upward through an inclined pipe as shown. Determine the flow rate. Ans. 7.64 L/s 6 cm diameter P2 250 kPa 40 Pi 350 kPa
2. An oil having a specific gravity of 0.80 has a kinematic viscosity of 2x10$ m²/s flows in a 100mm diameter pipe at a rate of 0.001m³/s. a. Compute the Reynolds number b. Determine the equivalent absolute viscosity c. Determine the centerline velocity
Please solve chapter Analytical Positioning Reactions max 30-45 minutes thank u A beam with bearings A (rolls) and B (joints) is loaded as shown in the figure. Given : The working moment is 96 kNm at B, and the load is evenly distributed to the triangle acting 16KN/m on the high side of the triangle. Question: Calculate the magnitude of the deposition reaction at A and at B in an analytical way, include the units and indicate the direction of the reaction Note : In Image A = rolls B = pin/joints
(c) Venturi-type flowmeter shown in Figure 5 is used to obtain the flowrate of oil inside a conduit. The diameter of the venturi, d is one third of the pipe diameter, D. The pipe diameter D is 6 cm, pressure difference reading AP, is 25 kPa, discharge coefficient Ca, is 0.98, Bis the ratio of venturi diameter to pipe diameter and oil specific gravity, SG is 0.95. i) Calculate the volume flowrate of oil inside the conduit. ii) Determine the mass flowrate of oil inside the conduit. iii) Explain why the discharge coefficient Ca, for the ventury meter is higher compared to the nozzle meter. 2(P – P.) V. ventury AP oil d Figure 5