An 8 m long steel is simply supported at the left end and 2 m from the right end. It carries a total uniform load of 45 kN/m all throughout its length. STEEL DECION CIVIL ENGINEERING Beam properties: A 11,500 mm² bf = 250 mm tw = 10 mm d == 350 mm If=: 16 mm lx = 266 x 10 mm If the Beam is laterally supported throughout the beam b) Determine the Maximum Web Shear Stress

An 8 m long steel is simply supported at the left end and 2 m from the right end. It carries a total uniform load of 45 kN/m all throughout its length. STEEL DECION CIVIL ENGINEERING Beam properties: A 11,500 mm² bf = 250 mm tw = 10 mm d == 350 mm If=: 16 mm lx = 266 x 10 mm If the Beam is laterally supported throughout the beam b) Determine the Maximum Web Shear Stress

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q3. Two steel plates (A572, Fb = 50ksi) are welded together to form an inverted T-beam. Determine the maximum bending stress developed. ( %3D | 10 Marks) 10k 15 k 6ft 5 ft 10 ft 5 ft A B 8ft 1ft
Question 3 of 5 -/ 20 E View Policies Current Attempt in Progress A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 580 mm2. If the stress in the bar must not exceed 330 MPa and the maximum deformation in the bar must not exceed 13 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b 2.4 m, and c = 5.2 m. %3! C (1) a Answer: kN P = Attempts: 0 of 1 used Sub Save for Later B.
The T-beam in the floor system has a slab thickness of 90 mm and supported by beams 6.5 m span. The beam is casts monolithically with the slab. The spacing of beams is 2 m on centers and width the web is 400 mm. The effective depth of the beam is 600 mm. It is reinforced at tension side with 8-28mm Φ bars. fc’ = 28 MPa, fy = 415 MPa 1. Which of the following most nearly give the effective width of the flange? a. 1565 mm b. 1305 mm c. 1275 mm d. 1625 mm 2. Which of the following most nearly gives the depth of compression block? a. 62.25 mm b. 52.86 mm c. 60.26 mm d. 58.29 mm 3. Which of the following gives the nominal moment capacity of the beam? a. 1461.25 kN/m b. 1156.36 kN/m c. 1163.15 kN/m d. 1172.58 kN/m
11. Link BC is 6 mm thick and is made of a steel with a 450-MPa ultimate strength in tension. What should be its width w if the structure shown being designed to support a 20-kN load P with a factor of safety of 3? 600 mm- A B 90 480 mm
Question 15 The design shear resistance, Vpl.Rd of a fully restrained simply supported Universal Beam with yield strength 345 N/mm² is 1,285 kN A point load of magnitude 1,906 kN is applied at the beam's mid-span The area of the web of the beam is Aw = 5,505 mm² The plastic modulus is Wpl.y = 2,979 cm³ The thickness of the beam web is tw = 12.6 mm Find the reduced design moment of resistance of the beam Mc,Rd (use the formula for l-cross-sections with equal flanges and bending about the major axis) Give your answer in kNm to the nearest whole number. Do not include units in your answer.
Two vertical forces are applied to a beam of the cross section shown in Fig.2. Determine the maximum tensile and compressive stresses in portion BC of the beam.(Take R=h=25mm). 4 kN 4KN -le A What B 300 mm 300 mm
Strain in rods is zero prior to applying load Determine load P such that the axial stress in the steel pipe is 200 MPa P Imm GAP RIGIO PLATE .6m B RIGID SUPPORT 30 mm x 30 mm. AL BAR E = 73 GPA 100 mm E = 200 G PO A B A ØSTEEL PIPE w/ 5mm WALL
Determine the stress in each of the two vertical rods if the temperature rises 50 °C after the load P-75 KN is applied. Neglect the deformation and mass of the horizontal bar AB. Use Ea = 75 GPa, as=23.0 um/m °C. Aa 850 mm2 Es 210 GPa, as = 11.9 um/m.°C and As 650 mm2. %3D Steel Aluminum 2.5m 3m 3m 3 m 3m 75 kN
twork Analyze the truss shown using method of joints. The following are the values of the forces: P = 10KN Q = 20 kN R = 30 kN %3D centives Determine the following: CAR a. AE [Select] ements ents b. ČE [ Select] ons C. CD [Select] 40 kN 3 m F F 20 kN + 20 kN E 2 m rations C 5 m Drive A 65 2 5 5 m m m TI Pro P.
A truss is loaded as shown in the figure. The cross- sectional area of each member is 500 mm^2. Hint: Use method of section in getting the axial forces. Use the guide cutting sections. L-6 m+6m- N 25 kN 8 m 50 kN - a 8 m 50 kN 8 m 50 kN 8 m B. 9. Find the axial stress in member HK O 35.34 MPa O 31.12 MPa O 33.34 MPa O 37.12 MPa Question 10 10. Find the axial stress in member HJ. O 125 MPa О 123 МPа O 127 MPa O 129 MPa
Problem 1: The rigid bar ABC is supported by AD and BE. Determine: a. Inclination of member ABC after loading b. 8 at point E Members Properties: Member Materials Modulus Cross- sectional Area of Elasticity AD Aluminum 70GPA 450mm2 ВЕ Steel 200GPA 550mm2 E O •Im O:3m 45kN. t 0 4m
3G “. Asiacell %99 Home Work... adhomShupper H.W. 1: 4.3 m Two axial members are used to support a load P applied at joint B. • Member (1) has a cross-sectional area of A = 3,080 mm2 and an allowabl normal stress of 180 MPa. • Member (2) has a cross-sectional area of Az = 4,650 mm2 and an allowable normal stress of 75 MPa. Determine the maximum load P that may be supported without exceeding either allowable normal stress. 5.0 m 2.0 m