A uniform rod of mass m and length L is connected to the floor by a frictionless hinge. The rod is initially at rest in a vertical position, but begins to fall and rotate about the hinge. The acceleration due to gravity is g. Determine the expression for net work Was a function of the angle 0, which is measured between the floor and the rod. W(0) = amel (1-ano) Sine function is missing parentheses around its argument

A uniform rod of mass m and length L is connected to the floor by a frictionless hinge. The rod is initially at rest in a vertical position, but begins to fall and rotate about the hinge. The acceleration due to gravity is g. Determine the expression for net work Was a function of the angle 0, which is measured between the floor and the rod. W(0) = amel (1-ano) Sine function is missing parentheses around its argument

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter10: Rotational Motion

Section: Chapter Questions

Problem 26P

See similar textbooks

Similar questions

Show that when A+B=C then A2+B2+2ABcos , where is the angle between vectors A and B .
Which of the following statements is true about the relationship between the dot product of two vectors and the product of the magnitudes of the vectors? (a) AB is larger than AB. (b) AB is smaller than AB. (c) AB could be larger or smaller than AB, depending on the angle between the vectors. (d) AB could be equal to AB.
Consider the vectors À = 6i + 3j and B = 3i - 6j.
A ladder 2.00 m long, weighing 234 N, initially lies flat on the ground The ladder is raised to a vertical position Compute the work done by the force lifting the ladder. The ladder's center of gravity is at it geometric center?
In this problem we are going to consider two different examples of the dot product between two vectors, a force F and a displacement delta r. (a) if the force vector has a magnitude of F= 19 N, The displacement has a length of deltas=1.2 m, and the angle between the vectors is 35°, what will the dot product between the vector F and the vector delta r be? You can answer in Joules (which is the same as Newton meters) . (B) if the force vector has components fx =8.5 N and F y=12 N, and the displacement factor has components delta rx=0.15 m and delta ry=0.61m, what is the dot product between them? Again, enter the answer in joules.
Problem 151. One end of a rod of mass 1 kg and of length 1 m can freely rotate about a lixed horizontal axis. Initially the rod makes an angle of 30° to the horizontal. A thread of length 1.3 m is attached t0 the (wo ends of the rod. A small pulley can run without friction along the thread, and a weight of mass 0.2 kg is suspended on the axis of the pulley. Determine the work needed to lit the rod to a horizontal position. (Use the value g= 10 m/s? for the acceleration due to gravity.) 30° 1 m
Given M = 3 î + j- 3k and N = 5 Î – 4 ĵ – 4 k, calculate the vector product M x N. Need Heln? Read It
Two vectors live with their tail at the same point. When the angle between them is increased by 20 degrees is there is colour product has the same magnitude but changes from positive to negative. The original angle between them was
"If vectors A = 4i + 3j + 2k and B = 2i + 3j + 4k, then the dot product A.B will be equal to"
Two identical, thin boards are hinged together at an end as shown below. The length of each board is l, and the total mass of each is m. Initially, one board hangs down freely from the hinge while the other is held at angle 00 by a horizontal string. Ignore any friction. (a.) Find the string's tension. Answer: "mg tan 00 (b.) If the string is broken, what is the incoming board's kinetic energy Ko just before impact? Answer: mgl (1 – cos 60) 2 (c.) Find the incoming board's angular momentum L just before impact. Make use of Eqn. (2) to minimize the algebra. Answer: L2 = m²gl® (1 – cos 0) (d.) Show that the kinetic energy of both boards just after the impact is Ko/2. Assume the collision is completely inelastic. Hint: Apply Eqn. (2) to minimize the algebra. (e.) To what angle do the boards rise after the collision? Answer: arccos (3/4 + 1/4 cos 00)
What is the angle between two unit vectors if their dot product is 0.5?
In this problem we are going to consider two different examples of the dot product between two vectors, a force F and a displacement Δr. If the force vector has a magnitude of F = 14.5 N, the displacement has a length of Δr = 0.75 m, and the angle between the vectors is 45°, what will the dot product between the vector F and the vector Δr be? You can answer in joules (which is the same as newton-meters). If the force vector has components Fx = 7.5 N and Fy = 13.8 N, and the displacement vector has components Δrx = 0.25 m and Δry = 0.63 m, what is the dot product between them? Again, enter your answer in joules.