A two-stage active band pass filter (BPF) is shown in Figure Q2. A table of components values is shown in Table Q2. For this BPF: a) Calculate the passband voltage gain in dB and the quality factor Q of each stage. b) Calculate the critical frequencies and bandwidth of the filter. c) Sketch the frequency response of the filter. CA RA RA Rc RB Figure Q2. CB=27NF RA=2kQ RB=1kQ Rc=4700 RD=3300 CA=56NF Table of Component values of the BPF Table Q2 HH

A two-stage active band pass filter (BPF) is shown in Figure Q2. A table of components values is shown in Table Q2. For this BPF: a) Calculate the passband voltage gain in dB and the quality factor Q of each stage. b) Calculate the critical frequencies and bandwidth of the filter. c) Sketch the frequency response of the filter. CA RA RA Rc RB Figure Q2. CB=27NF RA=2kQ RB=1kQ Rc=4700 RD=3300 CA=56NF Table of Component values of the BPF Table Q2 HH

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the filter: a) Determine type of filter and the cut-off frequency (Fc). Determine the peak voltage at the cut-off frequency (Fc). b) Find GAIN (Vo/Vi) at f = .1*Fc . Find GAIN (Vo/Vi) at f = 10*Fc . c) Determine the frequency at which GAIN = .4 (i.e., Vo = .4*Vi) . Draw the “Frequency Response Plot” in “Log-Log” format .
A) Write the equation for the small-signal gain function Vout/Vinfor the followingop-amp circuit B) What kind of filter is this circuit? C)Write the equation for the cutoff frequency of the filter D) Sketch the Frequency Response of the system
Define and differentiate the following terms. Also Draw plots where required. You can use different symbols to denote each term a. Gain Cross over Frequency VS.Phase Cross over Frequency b. Phase Margin VS. Gain Margin c. Three Conditions of Stability in terms of phase cross-over frequency and gain-cross over frequency. Three Conditions of Stability in terms of phase margins and gain margins
Sketch the waveforms of the inductor current, the current through the filter capacitor branch, and current through the load resistance. Describe the nature of the current through the equivalent series resistance (ESR) of the capacitor. What is the effect on the shape of the current when the value of the ESR is increased? Explain how the switching frequency component is eliminated by the output filter network. The efficiency of the buck converter decreases with an increase in the load current. Justify What is the effect of increasing switching frequency on the current ripple of the converter?
1. Choose which basic filter response suit the signal output criteria in the figure 2. State your reason. 2. Sketch the basic filter response to suit the output citeria in Figure 2. (with labelling of passband, transition region and cut-off frequency). 3. Choose 1 type of filter if a flat pass-band gain response is required.
Define linear phase filters. Explain why we use linear phase filters.
A three-stage system comprised of two amplifiers and one filter. The input power Pin= 0.1mW. The absolute power gains are Ap1 = 100, Ap2 = 40, and Ap3 = 0.25 Determine a.) the input power in dBm, b.) output power (Pout) in watts and dBm, c.) the dB gain of each of the three stages, and d.) the overall gain in dB
) Discuss the advantages and disadvantages of series resonant circuit.
Define briefly the terms used in filter below, a) pass band b) attenuation band c) Cut off frequency (-3db frequency)
bessel bandpass filter analysis and all formula. lecture summary
What is a bandpass filter? How is its bandwidth defined?
1. Derive the lower cut-off frequency for the basic RC high-pass circuit in Figure 1. R, Figure 1.