A salt solution (30% Na2CO3) weighing 1ton is cooled to 20C where the salt crystallizes as decahydrate. What will be the crystal yield if the solubility is 21.5 kg anhydrous Na2CO3 /100kg water? (assume that 3% of the total solution is lost by evaporation)
Q: 12,07g of sodium chromate is dissolved in water to prepare 0,17dm^3 of solution .Calculate the…
A: The number of solute moles dissolved in a given solution is called the concentration of that…
Q: Describe the preparation of the following reagents. 1. 250 mL of a solution that is 0.0376 N Mgl2…
A: (1) Given that - Volume of Magnesium iodide, Mgl2 solution = 250 mL Normality of magnesium…
Q: (1a) Pure benzophenane freezes at 66.6 °C. A solution of 7.75 g of biphenyl (C12H10; molar mass =…
A:
Q: The solubility of acetanilide in hot water (5.5 g/100 ml at 100 o C) is not very great, and its…
A: Assuming you chill the 100 mL down to 0 degrees, the 100 mL will hold onto 0.53 grams of…
Q: Calculate the formal concentration in molarity of a sodium acetate soluti on prepared by diluting…
A: we know 1ppm=1mg/L=10-3g/LNow we can convert ppm to molaritymolarity=mass of…
Q: The density of a 2.25 M resolution with ethanol C2H5OH is measured at 0.977 g/mL. Calculate mass…
A: Here we have to determine the mass percentage of ethanol in the given solution.
Q: 2furoic adid isa white solid that follows this usual pattern as, 1 gram of 24uroic acid disolves in…
A: The experiment is based on the recrystallization of 2-furoic acid.
Q: A mixture of 5.0 g A, 5.0 g B, and 5.0 g C were separated by recrystallization using ethyl acetate…
A: Given, mass of A = 5 g, B = 5g and C = 5 g. table : A : cold = 1.7,hot = 2.5 B: cold =…
Q: a) Which salt has minimum solubility at40°C? 200 100 KNO 160 170 160 b) At what temperature…
A: We give answer from the study of solubility curve.
Q: 4.0g of potassium hydrogen tartrate was added to 300mL distilled water. The temperature of the…
A: We are given initial and final pipette reading for 1.0 M NaOH and we have to find volume and moles…
Q: Consider the following two white solids below and their physical properties based on information…
A: From the given information we get the answer
Q: A 0.25g nonelectrolyte solute (MW=124.5g/mol) is dissolved in 100g solvent (MW-82.90g/mol) have a…
A:
Q: 1. A mixture of organic solvent (nitrobenzene) and water boils at 363K. The vapour pressure of water…
A:
Q: The distribution coefficient, KD (C water/C ether), between ether and water for aspirin at room…
A:
Q: Question attached
A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…
Q: 2.2 The solubility of nitrogen gas at 20°C is Cs,N2 = 19 mg/L. (a) Calculate the maximum molar and…
A:
Q: Orthophosphate (PO4³) is determined by weighing as ammonium phosphomolybdate, (NH4)3PO4 •12MOO3.…
A:
Q: Uranium tetrafluoride and zirconium tetrafluoride melt at 1035 °C and 912 °C respectively. They form…
A: The melting points of uranium tetrafluoride and zirconium tetrafluoride are given as 1035°C and…
Q: The solubility is 12.8g in 100mL of ethanol at 0 degrees C, and 46.4 g in 100mL of ethanol at 60…
A: Given, the solubility is 12.8g in 100mL of ethanol at 0 degrees C and 46.4 g in 100mL of ethanol at…
Q: The partial molar volumes of water and ethanol in a solution with XH2O 0.45 at 25°C are 17.0 and…
A: The change in volume mixture for the two compounds are mixed compared with unmixed is calculated as…
Q: A 690 g of 59% strontium bromide solution is cooled from 60 oC to a certain temperature. Upon…
A: Given : Mass of solution = 690 g Mass of SrBr2 precipitated out on cooling producing saturated…
Q: The solubility of acetanilide in hot water is 5.5 g/100 mL at 100 °C and its solubility in cold…
A: The calculation you did for part a is wrong. This does not work this way. The volume turns out to…
Q: Potassium permanganate (KMnO₄) has a solubility of 6.4 g/100 g of H₂O at 20°C and a curve of…
A: We can prepare a solution that contains more than the equilibrium concentration of dissolved solute.…
Q: Describe the preparation of the following solutions: a) 500 ml of approximately 0.2M NaOH (40g/mol)…
A:
Q: Identify 2 sources of errors in each of the steps in making of a solution. Explain whether a…
A:
Q: If 30.0 mL of water that is 0.0500 M in Q is to be extracted with four 10.0 mL portions of an…
A: The final aqueous concentration in solvent extraction method is as shown below: Here, Initial and…
Q: Distinguish between zeolite and ion exchange processes of softening water. A water sample when…
A: Hard Water is always converted into soft water. Hard water always has a higher mineral content when…
Q: a) Which salt has minimum solubility at40°C? 200 180 KNO, 180 170 160 b) At what temperature…
A:
Q: saturated solution of sulfur dioxide is prepared by dissolving SO2 (g) in 100g of water at 10°C and…
A: Solubility of a compound is defined as the minimum amount of solute (mass) present in 100 g of a…
Q: The solubility of compound B is 59 g per 100 mL in boiling methanol and 30 g per 100 g in cold…
A: For recrystallization to be effective, the optimal solvent must be used. The desired compound should…
Q: A mixture of 5.0 g A, 5.0 g B, and 5.0 g C were separated by recrystallization using ethyl acetate…
A: To calculate percent purity and percent recovery of the purified crystal after one recrystallization
Q: The 250-mL coke was then opened. Given the atmospheric pressure is 1 atm and volume percent of CO2…
A: Daltons Law is given as
Q: A 690 g of 59% strontium bromide solution is cooled from 60 oC to a certain temperature. Upon…
A: Given : Mass of solution = 690 g Mass of SrBr2 precipitated out on cooling producing saturated…
Q: Assume you dissolve 30.0 g of cobalt sulfate heptahydrate (CoSO4.7H2O) in 500 ml of a 1.0 M H2SO4…
A: Molarity = Number of moles of soluteVolume of solution (in L)Number of moles of solute = Given…
Q: Consider the following two white solids below and their physical properties based on information…
A: We are given a mixture of camphor and cinnamic acid to separate.
Q: A solution was prepared by dissolving 1210 mg of K3Fe(CN)6 (329.2 g/mol) in sufficient water to give…
A: Molarity is defined as number of moles of solute per liter of solution. M = n/V where, M = molarity…
Q: 1. Describe the preparation of 500mL of 0.500M KMNO4 from the solid reagent. 2.Describe the…
A: For preparation of particular solution, the weight of solute and volume of solution must be known.…
Q: An organic chemistry student isolates 738 mg of salicylic acid (SA) and decides to use methanol in…
A: Weight of salicylic acid = 738 mg = 0.738 g Solubility in methanol At 0°C = 41.3 g/100 ml At 56°C =…
Q: Roughly, what is the error introduced by the solution of some of the CO2 in the water in the bomb?…
A:
Q: The partial molar volumes of water and ethanol in a solution with XH20 = 0.45 at 25°C are 17.0 and…
A: Given partial molar volume of water, VmW = 17.0 cm3/mol or 17.0 cm3.mol-1 partial molar volume of…
Q: ... متعد د الخيارات What is the volume of sulfuric acid H2S04 needed to prepare a dilute solution of…
A:
Q: Na < NaCl < Na2O
A:
Q: Suppose the rate of evaporation in a hot, dry region is about 2m per year, and the seawater there…
A: Given,Rate of evaporation = 2 m per yearSalinity of seawater = 35 pptYield of NaCl = 90 %Area of…
Q: a-) What is the concentration of 250 mL of solution containing 0.125 grams of iron in ppm? b-)…
A: Required Conc=0.3 M volume=200 ml So , moles=200 x 0.3 =60 milli…
Q: To prepare orange chrome dissolve 2g of lead acetate in 25cc of Warm distilled water, add 4cc oF 2…
A: Chrome orange is a mixed oxide with the chemical formula, Pb2CrO5.
Q: Describe the preparation of 800 mL of 2 M HCl from the commercial reagent that is 37.5% HCl (%w/w)…
A: Volume of HCl =800 mL Molarity of HCl = 2 M Mass percent of HCl = 37.5 % Mass of Solution = 100 g…
Q: A student investigated the stoichiometry of the reaction of zinc (Zn) with HCI solution and reported…
A:
Q: Describe the preparation of 400 mL of 6 F H;PO4 from the commercial solution which is 85% (w/w)…
A: Since you have asked multiple question, we will solve the first question for you.If you want any…
A salt solution (30% Na2CO3) weighing 1ton is
cooled to 20C where the salt crystallizes as
decahydrate. What will be the crystal yield if
the solubility is 21.5 kg anhydrous Na2CO3
/100kg water? (assume that 3% of the total
solution is lost by evaporation)
Trending now
This is a popular solution!
Step by step
Solved in 3 steps
- Caustic potash that has been exposed to air is found on analysis to contain 90.00% KOH, 2.38% K2CO3 and 7.62% H2O. What weight of residue will be obtained if 1.00 g of this sample is added to 46.00 mL of 1.00 N HCl and the resulting solution, after neutralization with 1.070N KOH is evaporated to dryness?A fertilizer railroad car carrying 34,300 gallons of commercialaqueous ammonia (30% ammonia by mass)tips over and spills. The density of the aqueous ammoniasolution is 0.88 g>cm3. What mass of citric acid,C(OH21COOH21CH2COOH22, (which contains three acidicprotons) is required to neutralize the spill? 1 gallon = 3.785 L.When a Vitamin C (ascorbic acid; MM = 176.12 g mol-1) tablet is crushed, dissolved and titrated with 0.0340 M KIO3(aq) to a purple/blue endpoint (given by a starch indicator), the volume of KIO3 used is 29.80 mL. If 60 mg of ascorbic acid is the recommended dietary allowance (i.e., 100% of the RDA), then what is the % RDA for the Vitamin C in the tablet? KIO3(aq) + 5 KI + 6 H+ → 3 I2(aq) + 3 H2O I2 (aq) + ascorbic acid → 2 I- + dehydroascorbic acid
- To analyze an aspirin sample, 0.3470 g of crushed tablets are weighed and treated with 50.00 mL 0.1155 M sodium hydroxide, boiling for 10 minutes. Under these conditions the acid acetylsalicylic (MW, 180) reacts according to: CH3COO-C6H4-COOH + 2 OH- → OH-C6H4-COO- + CH3COO- The excess NaOH is then titrated with 11.5 mL of 0.2100 M HCl. What is the purity of said show ?.What is the water solubility of BaCO3 (Kep = 2.6 x 10-9) in a solution containing 0.40 M CO, (aq)? %3DA sample of processed meat scrap weighing 4.000 g is digested with concentrated HSO. and Hg(catalyst) until the N present has been converted to NHHSO.. This is treated with excess NaOH, and the liberated NHs is caught in a 100-ml of H.SO. ( Iml 0.01860 g Na:OJ. The excess acid requires 57.60 ml of NaOH ( ImL = 0.12660 g potassium acid phthalate, KHCaH.OJ. Calculate the percentage protein in the meat scrap 4.
- calculate the solubility of ca3(po4)2 in water ksp = 2.07 x 10-33A 9.12g of KClMgCl26H2O is to be dissolved to prepare a solution in sufficient water to give 1.500L. What is the molar analytical concentration of KClMgCl2 in this solution?The calcium (AW= 40.08 g/mol) from a sample of limestone weighing 607.4 mg was precipitated as calcium oxalate hydrate (CaC204.H20, FW 146.12 g/mol) and ignited to calcium carbonate (CaCO3, FW= 100.09 g/mol) weighing 246.7 mg. (c) If the precipitate had been ignited at a higher temperature giving calcium oxide (CaO, FW= 56.08 g/mol), what would be its weight?
- Empirical formula is 6C. % of Sulphur= [S] x 100 S0.0- yd ebivic 32 x 100% = 50%m %3D [1 (32) +2(16)] (CH,)n=2x42 [Hint: M,= 2x V.D] (12+2)n=84; n=6; hence compound is C,H,2 Mg + 2HCI → MgCl, + H, 7A. 8. From the equation: alumoeluaalch = slumot leohioma 1mol Mg produces 1mol H, Or 24g Mg produces 22.4dm' H, ei sid 9B. Compare Q57 n negyoro lo on lsic CHAPTER 3 eo to easm yd. THE ATOMIC STRUCTURE. ELECTRONIC CONFIGURATION. PERIODICITY OF ELEMENTS. - The periodic classification of the elements is an arrangement of the elements in order of their A. atomic weights B. isotopic weights C. molecular weight D. atomic numbers E. atom masses (1978:Q5) SD . The nucleus of an atom contains A. protons only B. neutron only C. protons and electrons D. neutrons and electrons E. protons and neutrons not iso(1978:Q28) - The size(diameters) of five atoms are in order R1) The solubility product of silver carbona (Ag2CO3) in water is 8.5 x 10-12. How many grams of A92CO3 have been dissolved in 400 ml of aqueous saturated aqueous solution of Ag2CO3? (Ag = 107.8 g/ mol, O = 16.0 g / mol, C = 12.0g / mol) %3DThe solubility of water in diethyl ether has been reported to be 1.468 % by mass.' Assuming that 23.0 mL of diethyl ether were allowed to become saturated with water before used, and that the 1.2 g magnesium was the limiting reagent, what percentage of the product is expected to be lost due to the water in the solvent if the ether is not anhydrous?SEE MORE QUESTIONS