A polystyrene rod consisting of two cylindrical portions AB and BC Is restrained at both ends and supports two 5-kip loads as shown. Take E= 0.45 x 106 psl. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 25 in 15 in A -1.25 in B С termine the normal stress in each portion of the rod. e normal stress in portion AB is ksl. e normal stress in portion BC Is ksl.

A polystyrene rod consisting of two cylindrical portions AB and BC Is restrained at both ends and supports two 5-kip loads as shown. Take E= 0.45 x 106 psl. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 25 in 15 in A -1.25 in B С termine the normal stress in each portion of the rod. e normal stress in portion AB is ksl. e normal stress in portion BC Is ksl.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

gure 1 shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined from solid aluminium alloy stock, subjected to a tensile load of 30kN. If Young's odulus for the alloy is 69GPA determine the stress in section 2. Answer to be provided in MPa, correct to three decimal places - do not include a unit with your answer. L1 L2 L3 d2 d3 P Figure 1
A picce of wire 10-in long is tied vertically. The wire has a diameter of 0.1-in and is used to support a load of 100-lb. What is the stress developed within the wire? 1.
1. Problem 1: Segment AB of the bar is a hollow tube with an outer diameter of 1.5 inches and a wall thickness of 0.125 inch. Segment BC is a solid rod of diameter 0.75 inch. Determine the normal stress in segment AB in psi. 0.125 in. 0.75 in. 4800 lb 2800 lb 1.5 in. B C |A -6 in.- -6 in. Your answer 2. In Problem 1, determine the normal stress in segment BC in psi. Your answer
Q1/ The aluminum and bronze cylinders are centered and secured between two rigid end-plates by tightening the two steel bolts. There is no axial load in the assembly at a temperature of 50°F. Find the stress in the steel bolts when the temperature is increased to 200°F. Use the following data: 1.0 in. -3 in--4 in. F1.0 in. A (in.?) a (J°F) E (psi) Aluminum cylinder 2.00 12.8 x 10-6 10 x 106 Bronze cylinder 3.00 10.5 x 10-6 12 x 10 Aluminum Bronze Each steel bolt 0.75 6.5 x 10-6 29 x 10 Q2/ The rigid bar ABCD is supported by a pin at B and restrained by identical steel bars at C and D, each of area 250 mm?. If the temperature is increased by 80°C, determine the force P that will cause the bar at C to be stress-free. Use E = 200 GPa and a=12.8*10PC 3 m 0.8 m 0.6 m Ce D P
The horizontal cross-section of the cast-iron standard of a vertical drilling machine has the form shown. The line of thrust of the drill passes through P. Find the greatest value the thrust may have without the tensile stress exceeding 15 MN/m2. What will be the stress along the face AB? (Cambridge) 12.4 19.0cm A 36 cm 1.60 cm 1.90 cm 1.60 cmT B. +17.5cm
H. W2: A rectangular column of sides 0.4mx0.35m, made of concrete, is used to support a compressive load of 1.5MN. Four steel rods of each 24mm diameter are passing through the concrete as shown in figure 1.23. If the length of the column is 3m, determine the normal stress in the steel and the concrete. Take Esteel 200 GPa and Econcrete = 29 GPa. steel rod: 0 24 mm 0.4 m 3 m 0.35 m
Question 5 Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 22 kN if it developed a stress of 40 MPa. Take note that the inner diameter is 4/6 of the outer diameter.
1. A BRONZE ROD IS SUBJECTED TO A TENSILE LOAD OF 15,000N. IF ITS ALLOWABLE STRESS IS 75 MPa, CALCULATE THE OUTER LENGTH OF THE SIDE OF THE PENTAGONAL TUBE IF THE INNER LENGTH OF THE ONE SIDE IS 40mm. 15,000N 15,000N 40mm CROSS-SECTION OF THE BRONZE ROD BRONZE ROD
Write the Glven and what is being asked. .Write your complete solution. . Round off your answers into TWO decimal places. BOX your fial.answer and don't forget the units.
The rigid bar AB shown below is supported by a steel rod AC having a diameter of 20 mm, and a block. Ignore the weight of AB and AC, and the distributed load on AB is p = 4.0 KN/m. Determine the axial normal stress developed in AC: = ____ MPa. Calculate your answer to 1 decimal place.
Question 1: Given that Tuitow = 50 MPa for the rod AB and tattow = 25 MPa for the rod BC. If T=1250 N.m, find the required radius for both rods. Ahmtmum AB = BC =
Determine the compressive force (in Ib) in the bars shown after a temperature rise of 149°F if d = 0.012 in. Round off the final answer to five decimal places. d ... L M Use the following data: Bronze Aluminum A = 2.24 sq. in A = 2.73 sq. in E = 14930924 psi L = 13.4 in E = 10543748 psi L= 16 in a = 11.76 x 10-6/ °F a = 12.54 x 10-6/°F