A hydraulic system is used to apply a force in an external fixation device to hold broken ends. The piston of this hydraulic ram is 30 cm in diameter and the water pressure (shaded portion of the sketch) is 3 MN/m² as shown in Figure QI.1. 3 MN/m 30 cm 4 cm Figure QI.I Hydraulic system Determine: 1.I. The stress in the piston rod which has dimeter of 4 cm 1.2. The elongation of the 2 m long piston rod. Take Young's modulus as E- 200 GN/m²

A hydraulic system is used to apply a force in an external fixation device to hold broken ends. The piston of this hydraulic ram is 30 cm in diameter and the water pressure (shaded portion of the sketch) is 3 MN/m² as shown in Figure QI.1. 3 MN/m 30 cm 4 cm Figure QI.I Hydraulic system Determine: 1.I. The stress in the piston rod which has dimeter of 4 cm 1.2. The elongation of the 2 m long piston rod. Take Young's modulus as E- 200 GN/m²

Name: 1.A hydraulic system is used to apply a force in an external fixation
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 1.A hydraulic system is used to apply a force in an external fixation device to hold brokenends. The piston of this hydraulic ram is 30 cm in diameter and the water pressure (shadedportion of the sketch) is 3 MN/m² as shown in Figure QI.1.3 MN/m30 c

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

YI G &UIK AR Googk 1 Nte uole L 5 ps The pressure gauge fitted on a water tank (see Figure) shows a reading of 19620 N/m2. The curved surface PQ of the top is quarter of a circular cylinder of radius 1.4 m. Find the magnitude (in kN) and direction (in °) of the resultant pressure force acting on the curved surface if the width of the tank is unity. Imaginary water surface R 2 m 19620 N/m2 P Fy FH- 1.4 m Water tank O 56.455, 0.4894 56.455, 48.94 56.455, 4.894 O 56455, 48.94 O I do not wish to attempt hp
1o An aquarium 7 m long, 5 m wide, and 4 m deep is full of water. Find the following: the hydrostatic pressure on the bottom of the aquarium the hydrostatic force on the bottom of the aquarium the hydrostatic force on one end of the aquarium esc @ 23 2$ % 2 3 4. 7 e
Use p F t A river is blocked by a dam with the shape of an trapezoid. The dam is 20 m tall, 20 m at its base and 40 m on top. What is the total force acting on the dam if the water reaches the full height of the dam? = 40 m Enter your answer in scientific notation to at least 2 significant figures. kg m 1000 and g = 9.8- m³ - 20 m 20 m N
An automobile lift in the Karsha car wash and service station raises 5.6 kN car of 2.4 m above the floor level from the ground,As shown in the below given figure , If a hydraulic cylinder has a piston of diameter 234.5 cm . Find the following: (a) Necessary Work to lift the car vehicle (in J) (b) Required Pressure to lift the car.in pascal (c) Power needed to the raise the car in 0.8 minutes in kW
An automobile lift in the Karsha car wash and service station raises 5.6 kN car of 2.4 m above the floor level from the ground,As shown in the below given figure , If a hydraulic cylinder has a piston of diameter 234.5 cm . Find the following: (a) Necessary Work to lift the car vehicle (in J) (b) Required Pressure to lift the car in pascal (c) Power needed to the raise the car in 0.8 minutes in kW (d) Speed of the the lift for 505 m3 per minute in m/s and Required flow rate for the vehicle to descend in 5.9 seconds. m3/s
Piston The piston shown in figure is held in equilibrium by the pressure of the gas flowing through the pipe. The pressures Pi = 350 kPa, p = 130 kPa, and pressure of the gas p 210 kPa. Find the mass of the piston. Ans: 80.1 kg „II k10 cm Pipe 20 cm Hints: Consider a free body diagram of the piston and identify the different forces the piston is subjected to get the weight of the piston. numerically equal to its mass since g is not given meaning at standard gravity. The weight of the piston is gas III
Find the resultant force f center of pressure for one Side of submerged area shoun in figure below. Water 1-3m 0.75 Fos 0.Sm hole of dia. = 0.6 m 1.5 K 1.5 t
): Find the hydrostatic pressure force acting on the ABCD curvilinear surface. (The width of the gate is 3 m). Draw hydrostatic pressure distribution on this figure. 2.4m Water Water 1.6 m ANAA
A cylindrical gate with surface XY is supported by a hinge at point 1. The length of the gate perpendicular to the figure ism. Solve for the magnitude of the horizontal component in kN. Unit wt of water = 9.81 kN/cu.m. LENGTH = 6 RADIUS 8 ANGLE=53 RADIUS X ANGLE 1 O 1,062.35 O 1,201.34 O2,003.99 O 2,436.65
H.W2: The tank in Fig. is 40cm wide. Determine the hydrostatic forces on horizontal plan BC and AD? 55 cm 40cm A -10cm 35c Solvent, sg=0.84 Water 25ci 2m Water. 20°C 4m Hg. 20 3m H.W3 water in a tank is pressurized to 85cmHg as show in Fig. Determine the hydrostatic forces per meter width on panel AB? note: Ans: =501 KN
): Find the hydrostatic pressure force acting on the ABCD curvilinear surface. (The width of the gate is 3 m). Draw hydrostatic pressure distribution on this figure. 2.4m Water Water 1.6 m
Here are these questions if I could get help with themIf a spherical storage tank holds 40,000 gallons (120,000 liters) of water,what diameter must it have?If a cylindrical storage tank has a 40-foot (12 m) diameter circular 05::=how high must it be to hold 1 million gallons (3 million liters)?If water is moving at a rate of 3.2 ft3/sec (90,000 cc/sec), how manygallons (liters) per minute is this?If the specific gravity of gold is 19.0. what is the weight of a cubic inch(cubic centimeter) of gold? A cubic foot (cubic meter)?