A hollow circular cold-rolled bronze [G1 - 6200 ksi] tube (1) with an outside diameter of 1.75 in. and an inside diameter of 1.00 in. is securely bonded to a solid 1.00 -in-diameter cold-rolled stainless steel [G2 = 12500 ksi] core (2) as shown. The composite shaft is subjected to a torque of T = 46 kip-in. Determine the magnitude of the torque produced in sleeve (1). (1) (2) T T. O 27.3 kip-in. 39.2 kip-in. 37.1 kip-in. O 30.0 kip-in. O 22.6 kip-in.

A hollow circular cold-rolled bronze [G1 - 6200 ksi] tube (1) with an outside diameter of 1.75 in. and an inside diameter of 1.00 in. is securely bonded to a solid 1.00 -in-diameter cold-rolled stainless steel [G2 = 12500 ksi] core (2) as shown. The composite shaft is subjected to a torque of T = 46 kip-in. Determine the magnitude of the torque produced in sleeve (1). (1) (2) T T. O 27.3 kip-in. 39.2 kip-in. 37.1 kip-in. O 30.0 kip-in. O 22.6 kip-in.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Similar questions

Two sections of steel drill pipe, joined by bolted flange plates at Ä are being tested to assess the adequacy of both the pipes. In the test, the pipe structure is fixed at A, a concentrated torque of 500 kN - m is applied at x = 0.5 m, and uniformly distributed torque intensity t1= 250 kN m/m is applied on pipe BC. Both pipes have the same inner diameter = 200 mm. Pipe AB has thickness tAB=15 mm, while pipe BC has thickness TBC= 12 mm. Find the maximum shear stress and maximum twist of the pipe and their locations along the pipe. Assume G = 75 GPa.
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
A steel 0.75-in diameter shaft (G= 12,000 ksi) is subjected to the following torques in lb-ft: TA = 10; TB = 30; TC = 70; TD = 50. The directions of the applied torques are indicated in the figure The bearings shown allow the shaft to turn freely. The length of each segment is equal to 38 in. (a) Plot a torque diagram showing the internal torque in segments (1), (2) and (3) of the shaft. Show the FBD of each segment using a double-headed arrow to represent each torgue. Determine (b) the maximum shear stress magnitude in the shaft. (c) the rotation angle of pulley C with respect to pulley A.
A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when constant 120 KW is applied. Use the following: G(alum)=28 GPa, a=1.80 m, b=0.80m & L=2.60 m. Assumed that the angle of twist is constant.The torque "T2" developed at right fixed support at B is ___KN-m 3.82 2.64 0.48 1.18 5.03
The torsional assembly consists of solid 1.6 in. diameter aluminum [G = 4,000 ksi] segments (1) and (3) and a central solid 2.0 in. diameter bronze [G = 6,500 ksi] segment (2). Segment lengths are L1 = L3 = 32 in. and L2 = 66 in. Concentrated torques of TB = 2T0 and TC = T0 are applied to the assembly at B and C, respectively. If the rotation angle at joint B must not exceed 3.0°, determine:(a) the maximum magnitude of T0 that may be applied to the assembly.(b) the maximum shear stress magnitude in aluminum segments (1) and (3).(c) the maximum shear stress magnitude in bronze segment (2).
1. The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the driver gear acts at a pressure angle of 20 degree. The shaft transmits a torque to point A of TA =340 N.m. The shaft is machined from steel with S,=420 MPa, Km2.5, S=134MPA and N=2. Draw shear and bending diagrams and calculate diameter of shaft. 250 mm 100 mm
A steel 0.75-in diameter shaft (G= 12,000 ksi) is subjected to the following torques in lb-ft: TA = 50; TB = 70; TC = 30; TD = 10. The directions of the applied torques are indicated in the figure. The bearings shown allow the shaft to turn freely. The length of each segment is equal to 38 in. (a) Plot a torque diagram showing the internal torque in segments (1), (2) and (3) of the shaft. Show the FBD of each segment using a double-headed arrow to represent each torgue. Use the same rule of signs as in the lecture. Determine (b) the maximum shear stress magnitude (ksi) in the shaft. (c) the rotation angle, in degrees, of pulley D with respect to pulley B. Note: Follow the rule of signs with FBD in each sections. Show complete step by step solution and proper FBD. Solid shaft: J = (₶/32 )( D4) Hollow: J = (₶/32)(D4 - d4)
3. A hollow aluminium tube used in a roof structure has an outside diameter 104mm and an inside diameter 82mm. The tube is 2.75m long and the aluminium has shear modulus G=28GPa. a. If the tube is twisted in pure torsion by torques acting at the ends, what is the angle of twist (in degrees) when the maximum shear stress is 48 MPa.b. What diameter d is required for a solid shaft to resist the same torque with the same maximum stress.c. What is the ratio of the weight of the hollow tube to the weight of the solid shaft
A solid and a hollow shaft, connected by a coupling, transmit power. The outside diameters of the shafts are the same and the inside diameter of the hollow shaft is 75 % of its outside diameter. The solid shaft is three times as long as the hollow shaft. Take the modulus of rigidity for both shafts as 80 GPa. (a) If the angle of twist for the solid shaft is 1°, find the angle of twist for the hollow shaft. (b) If the maximum shear stress in the solid shaft is 30 MPa, find the maximum stress in the hollow shaft.
A compound steel [G= 94 GPa] shaft consists of solid 28-mm-diameter segments (1) and (3) and tube segment (2), which has an outside diameter of 68 mm and an inside diameter of 63 mm. Assume L₁-0.2 m, L₂-2.2 m, L3-0.2 m and T-210 N-m. Determine: (a) the maximum shear stress T₂ in tube segment (2). (b) the angle of twist 2 in tube segment (2). (c) the rotation angle DIA of gear D relative to gear A. T Answers: (a) T₂ = (b) ₂ = (c) & DIA (1) = B i i L2 (2) MPa. C L3 (3) T D X
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
Q1: A motor driving a solid circular steel shaft transmits 30 kW to a gear at B (as shown). The allowable shear stress in the steel is 40 MPa. G=70 GA (a) What is the required diameter d of the shaft if it is operated at 1500 rpm? (b) What is the required diameterd if it is operated at 3000 rpm? (e) If the length of the shaft from the motor to the gear is 1 m, what are the angles of twist for the two speeds of rotation? Motor