a) Explain the construction of LVDT. Identify some suitable examples according to their applications

Q: example open loop system

A: In this question we discuss about open loop system

Q: State assumptions to represent the multimachine equations with a single machine infinite bus system.

A: Multi-machine system can be written similar to a one-machine system by the following assumptions: 1.…

Q: Explain the definitions of three sets of sequence components. Take voltages or currents for example,…

A: Three sets of sequence components: The power system fault causes an unbalanced condition of…

Q: Identify the minimum distance requirements between network cables and power sources and identify…

A: Cable is the medium in a network through which information moves from one network device to another.…

Q: In your own words and from your own understanding, avoid plagiarism or copying from the Course…

A: Power system requires transmission of power from generation end to the consumer end. The power…

Q: 4. What can installation records be used to determine while servicing equipment? A. Broken…

A: Installation record refers to an information of equipment ratings, measurement, etc. which is…

Q: 9.a. What should be done with the connector ferrule once a connector is attached to a fiber optic…

A:

Q: ix. What is the purpose of surge tank in hydro electric plant?

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: A bolted line to line short circuit is used to determine the thermal withstand rating of the cables…

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: 1. Circuit breakers should be included in the impedance diagram. (True/False)

A: SINGAL LINE DIAGRAM OF A POWER SYSTEM: A single line diagram is the representation of a power system…

Q: What is the function of Positioning and Orientation System (POS – GNSS+IMU) in LiDAR system, when…

A: The main function of positioning and orientation ( POS ) system is to determine the position and…

Q: With a neat sketch discuss the working of a Grid - connected system for power generation and explain…

A: According to guidelines we need to solve only the first question. According to the question we have…

Q: Q.4. Mention the specifications of EIA/TIA recognized cables and its standard number for each type…

A: With industry input, the TIA/EIA cable standards have been developed by the Telecommunications…

Q: Define interlocking in electrical systems. What is it's significance?

A: According to the given question, it is required to define interlocking in electrical systems along…

Q: 1-DO you need a repeater station if we used optical cable under the sea level? And why?

A: If we used optical cable under sea level then there is a chance that it lose or reduce its signal.…

Q: () List any three factors to be considered for mechanical design of overhead lines

A: According to our expert policy only one individual question is to answered.kindlybrepost the…

Q: 3) Draw the schematics of a HVDC and of a HVDC light, compare the systems evidencing advantages and…

A: HVDC means high voltage direct current is a method of electrical power transmission which uses…

Q: 8- Generally as of the operating voltage which of the following options are the correct words that…

A:

Q: 7. What is the object of equipment grounding? Briefl y describe the functions of substation…

A: The object of equipment grounding: To reduce as much as possible the emergence of any voltages in…

Q: differentiate between overhead service connection and under ground service connection with sketch

A: Overhead Service Connection:- Electric locomotives, trolleybuses, and trams receive their electrical…

Q: b. Ground-fault protection c. Service-entrance conductors d. Branch circuits

A: Given: The answer is shown below:

Q: If overcurrent protection is not provided at the source of a separately derived system, the…

A: All ordinarily conductive non-current-carrying metal parts and other conductive materials are…

Q: Explain in detail what is a nodal line. Provide an example and diagram for it.

A: In order to understand Nodal line we first have to understand some basic terms such as Wave…

Q: Please answer the question full sentence 5. Identify the minimum distance requirements between…

A: The minimum distance between the network cable and power sources is 50 millimeter or 2 inches.

Q: Label the parts of Tubular Steel Poles

A: Steel tabular poles are not commonly used poles these poles are used when there is need of low cost…

Q: Which of the following statements about equipment grounding conductors is true? A. Unacceptable…

A: Correct option is B that is ELECTRIC GROUND CONDUCTORS must be capable of withstanding the higher…

Q: With the aim of a schematic, explain the principle of high impedance busbar protection.

A: High impedance bus bar protection requires High impedance CT with high knee point voltage and the…

Q: write with technical material, digrams and pictures about Domestic electrical installation system

A: Domestic electrical installation system:

Q: (a) Describe how TLBs are used to increase paging efficiency.

A: TLB contain entries page table have been most recently used. The processor examines , the frame…

Q: In your own words and from your own understanding, avoid plagiarism or copying from the Course…

A: we need to explain the molded case circuit breaker

Q: recommended the testing of wiring installations for domestic load

A: A

Q: What is the purpose of sequence control

A: Sequence control is generally used to start or stop motors in a specific order. It is used when one…

Q: In your own words and from your own understanding, avoid plagiarism or copying from the Course…

A:

Q: resistance testing? A. Fall-of-potential B. Line surge C. Spatial shielding D. Leakage current c.3.…

A: 1) correct option is A because Its function is to keep your equipment or system as close as possible…

Q: What down the uses of performing maintenance on machine.

A: Maintenance of the machine is the process or work in which the machine is monitor continuously to…

Q: Some electricians do not bother to calculate the minimum size of neutral service conductor. They…

A: 3-phase star connection balanced system does not require a neutral wire in the system. Basically, in…

Q: Discuss  Suspension insulators are recommended in high voltage transmission lines.

A: Pin encasings become excessively cumbersome an uneconomical past 33 kV. Thus, for voltages higher…

Q: Identify the minimum distance requirements between network cables and power sources and identify…

A: 50 mm is the minimum distance required between the power source and network cables.

Q: Please provide a background study of maintenance and repair and argument in optical fiber cable…

A: Damage to optical fiber cable accidentally, hamper as we will see while digging within the ground…

Q: find the following parameters for the arcust below

A:

Q: list the material required for overhead service connection

A: Various Types of Electrical service connections - Overhead Underground Majorly overhead is…

Q: Describe in your own words the features of (i) Arduino UNO (ii) Arduino NANO (iii) Arduino MEGA With…

A: Discuss features of given Electronic board (i) Arduino UNO (ii) Arduino NANO (iii) Arduino MEGA With…

Q: node-voltage method

A:

Q: Which one of the following is the definition of slurry? a. Water only b. Animal waste (Dung) only c.…

A: definition of slurry

Q: Explain the working of LVDT with neat diagram.

A: LVDT :  LVDT is divice which translates linear motion into electrical signal

Q: (i) List any three factors to be considered for mechanical design of overhead lines

A: List of the factor to be design overhead transmission line

Q: How to verify the validity of the nodal analysis technique in solving electrical networks?

A: Given:   Brief description: In the above question they want to discuss the nodal analysis technique…

Q: 4.a. An intersystem bonding termination will typically be used as a ground junction for a/an A.…

A: Answer 4.(a) According to 214 NEC, Intersystem bonding method is only one bonding method permitted…