А cube with an edge of 2·5 cm as shown in Fig. 1.4 was tested in compression. Under a load of 400 kN it failed along a plane passing through the di- agonal of the top, and through the diagonals of the adjacent sides. Determine the result- 400kN 2.5cm ant normal and shear stresses on this plane at the instant of the failure. 400 kN

А cube with an edge of 2·5 cm as shown in Fig. 1.4 was tested in compression. Under a load of 400 kN it failed along a plane passing through the di- agonal of the top, and through the diagonals of the adjacent sides. Determine the result- 400kN 2.5cm ant normal and shear stresses on this plane at the instant of the failure. 400 kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.4.22P: , Solve the preceding problem using the numerical data: /) = 90mm, h = 280 mm, d = 210 mm, q = 14...

See similar textbooks

Similar questions

Created from steel and brassgraded Rod, two at each endplaced between the fixed wall, B60kN respectively from and D pointsand 40kn axial forceswere exposed. Accordinglysteel (Eçelik=200GPa andEpirus=105GPa) formed in ricemaximum stressescalculate.
Two vertical steel wires each 0.05 in. diameter and 48in. long support a light rod over a span of 12 in. A concentrated load of 60 lbf is then applied vertically downwards at a point 4 in. from one of the wires. Determine the load, stress and extension on each wire and the angular displacement of the rod from the horizontal assuming it does not bend. Use E = 29,000 ksi.
Q1- Prove that the shear stress of circular shaft under pure torsion is Tr %3D Tmax Ip Ere
3 m 5:54 PM φλ C D E H F B -2 m--2 m--2 m--2 m--2 m--2 m- 20 kN 30 kN 40 kN ( 50 ) l اس. © 2 Find the Vertical Support Reaction at G (in kN). Input the magnitude only (don't include negative sign). The tolerance for the answer is +/-0.01.
The two steel shafts (1) and (2) each Ø10 should be connected to each other with the help of the sleeve (3) (Øinner = 10, Øoutside = 15) also made of steel and two rivets at the points shown. The shaft (1) is firmly clamped on the left- hand side, the force F = 100 N acts on shaft 2 in the direction of the arrow. How are the brass round rivets to be dimensioned so that a safety of the coupling against failure of S = 10 is achieved? hole for rivets 1 F 3 a) What type of connection does a riveted connection have? b) What type of load does the rivet have? c) What is the diameter of the rivets? d) Which areas of the rivet are loaded? (Draw in figure and formula) e) Dimension the rivet
The horizontal bar ABC is supported by a pin at A and the two rods with identical lengths and cross-sectional areas (2 sg.in.) The rod at B is steel and the rod at C is aluminum. Neglecting the weight of the bar, determine the stress in the steel rod when the force W= 10 kips is applied. Use Es=29 x 10^6 psi and Ea=10 x 10^6 psi. Express your final answer in psi to the nearest whole number. Note: Do not include the unit in your answer. * 3 ft B A 5.5ft 1.5 ft →
The uniform 300-lb bar AB carries a 500-lb vertical force at A. The bar is supported by a pin at B and the 0:5-in. diameter cable CD. Find the stress in the cable. 4 ft A 3 ft 3 ft B. 500 Ib
The cylindrical steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. The column is separated from the concrete foundation by a square bearing plate. The working compressive stress is 26 000 psi for the column, and the working bearing stress is 1200 psi for concrete. Find the largest force P that can be applied to the column. Express your answer in Ib. 4 in. 3.5 in. 4/4 7 in.
2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless pully at D. If the allowable tensile stress oallow = 5.2 ksi for the cable, determine the required minimum diameter (inch) of the cable. The cylinder (connected at C) weighs 890 lb. Neglect weight and thickness of the bar AC. D 4 3 A C 5 ft 5 ft -4 ft 890 lb
The tires of the 4,240 lb sedan are 7.5 in. wide. Each tire contacts the ground over a distance of l = 4.3 in. as measured along the vehicle's length. Calculate the compressive stress between each tire and the road. The locations of the vehicle's mass center and the wheelbase dimensions are shown. 40 in.' 100 in. Calculate the compressive stress between the front tire and the road: (Express your answer using three significant figures.) OF psi Calculate the compressive stress between the rear tire and the road: (Express your answer using two significant figures.) |psi OR =
eparate triaxial compression tests are performed on identical soil samples. The soil is a saturated mixed soil. Both tests follow the procedure for consolidated–undrained conditions. At failure, the respective minor and major principal stress values are 20 kPa and 46 kPa for sample one and 40 kPa and 80 kPa for sample two. From these data, determine the value for fCU and the cohesion intercept c on the Mohr’s circle shear stress coordinate. (This problem can be solved graphically using the Mohr’s circle.) Question Separate triaxial compression tests are performed on identical soil samples. The soil is a saturated mixed soil. Both tests follow the procedure for consolidated–undrained conditions. At failure, the respective minor and major principal stress values are 20 kPa and 46 kPa for sample one and 40 kPa and 80 kPa for sample two. From these data, determine the value for fCU and the cohesion intercept c on the Mohr’s circle shear stress coordinate. (This…
The mechanism below consists of a solid shaft with a diameter of 2 in between A and B and a hollow shaft with an outside diameter of 7 in and a thickness of 1/2 in between B and C. A torque T = 3 kip-in is applied as shown at A and two forces, each P = 322 lb, are applied as shown at the ends of the levers connected to Point B. Determine the shear stress that occurs on the exterior of the hollow shaft between B and C. Express answer in nearest whole psi.