a compressor Wörking steady proces: 300 K in a heat exchanger at the compressor outlet. Using the data in the figure; determine a) The power required by compressor b) Mass flow rate of the water in the heat exchanger Su T-310 K T290 K si Değiştirici 3) T-300 K T 400 K Kompresör Hava T-300 K m=0,5 kg/s

a compressor Wörking steady proces: 300 K in a heat exchanger at the compressor outlet. Using the data in the figure; determine a) The power required by compressor b) Mass flow rate of the water in the heat exchanger Su T-310 K T290 K si Değiştirici 3) T-300 K T 400 K Kompresör Hava T-300 K m=0,5 kg/s

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter24: Expansion Devices

Section: Chapter Questions

Problem 8RQ: The TXV responds to an increased heat load by A. decreasing refrigerant flow. B. keeping refrigerant...

See similar textbooks

Similar questions

The TXV responds to an increased heat load by A. decreasing refrigerant flow. B. keeping refrigerant flow constant. C. increasing refrigerant flow. D. not reacting to changing heat loads.
Answer this ASAP,thx In a steam turbine, saturated steam enters the turbine at a pressure of 16 MPa and a pressure in the condenser of 8 kPa. The mass flow rate of the fluid entering the turbine is 100 kg/s. calculate: A) the power produced B) the rate of heat transferred to the steam passing through the boiler C) the thermal efficiency
Liquid water is heated inside the tubes of a shell and tube heat exchanger as shown in the figure below. The inlet temperature is 30 °C and the outlet temperature is 50 °C. The tube inside and outside diamters are 16 mm and 18 mm respectively. The mass flow rate in each tube is 0.25 kg/s. Refrigerant Gas Water Out Water In Refrigerant Liquid Estimate: a) The average velocity in each tube: b) The Reynolds number in each tube: c) The Nusselt Number of the flow inside each of the tubes: m/s
12- Water vapor at 20000kg /hour flows into a steam boiler with a specific volume of 225 kPa 0.7565 m ^ 3 / kg. Calculate the time required to increase 1 ton of water to 200 ° C in the boiler if the insulation of the boiler is bad and loses heat to the environment of 100 kW with the energy it takes from the fuel in the combustion chamber. A.) 2061sB.) 1117sC.) 7643 sD.) 965 sE.) 8973 s
A steam condenser receives 10 kg per second of steam with an enthalpy of 2570 KJ/kg. Steam condenses into liquid and leaves with an enthalpy of 160 KJ/kg, if cooling water passes through the condenser with temperature increases from 13oC to 24oC. Calculate the cooling water flow rate in kg/sec. pls dont skip anything show all solution including conversion of units
A heat exchanger uses medium pressure steam at 10 bar and 350 C to heat cyclohexane vapor from 100 C up to 275 C as shown in the figure below. The steam is available at a flowrate of 32 kg/h and it condenses completely in the heat exchanger and exits as saturated liquid condensate at 10 bar. a) How much heat (in kW) can be provided by the steam? b) How much cyclohexane can be processed in kg/h? Vapor Cyclohexane T = 100 C P = 1 atm Steam T = 350 C = 10 bar Condensate P Vapor Cyclohexane T = 275 C P = 1 atm P = 10 bar
Compressed liquid water at 10 MPa and 20 C enter a steam generator (Heat exchanger) which has a uniform 30-mm diameter tube at a rate of 3 L/s. Find the rate of heat added to the water (in kW) if it exists at 9 MPa and 400 C. Select one O a. 8333.8 kW O b. 8638.8 kW O C. 9131.2 kW d. 9556.4 kW O e. 7854.2 kW O f. None of the above
Hello! I'd like help with the following exercise, from Levenspiel's "Engineering Flow and Heat Exchange". Leftover air at 20ºC and 100kPa is driven by a fan through a horizontal galvanized conduit of 1 m in diameter and 10m in length at a speed of 10 m/s. What size motor should be used if its efficiency is 90% and that of the fan is 20%? I'm not sure where to start. My professor hasn't explained much about this subject.
2-) 10500 kg/hr of water is heated using a counter-flow, double-pipe heat exchanger utilizing superheated steam. Steam passes through the heat exchanger at 130 °C after entering at 180 °C. Water has an entrance temperature of 30 °C and an outlet temperature of 80 °C. Calculate the heat transfer area if the overall heat transfer coefficient from steam to water is 814 W/m² K. How much more area would there be if the fluid flow was parallel?
A large heat pump cools the river with a temperature of 223.15 K and flow of 10 m³/s by 3.0 K. The received heat is transferred to the hot water system with a temperature of 313.15 K. a) How much heat power does it gain in this way? (The solution is 126 MW) b) For how many inhabitants does the heating system suffice if each inhabitant needs 500 W of power for heating? (The solution is 250 000) c) How much electrical power does the pump need if the total losses are twice as large as for the equivalent Carnot machine? (The solution is 23 MW)
ROOM (2) 700kPa x=0 CONDENSER (1) 40°C 700kPa EXPANSION VALVE (3) 100kPa EVAPORATOR (4) 100kPa x=1 OUTSIDE Consider a heat pump cycle operating with R134-a fluid at 0.01kg/s mass flow rate. Conditions are given in the figure. a) What are the values of heat supply rate to the room and heat absorption rate from the outside? b) What is COP of this heat pump? c) Assume we immediately put a watermelon of 8kg to the room at 2°C. Assuming a specific heat of 4200J/kg for the watermelon, how long will it take for the watermelon to reach room temperature of 20°C if we assume that heat pump only heats watermelon? O A) 2.7 minutes B) 3.2 minutes C) 4.4 minutes O D) 5.3 minutes E) 6.2 minutes COMP.
A steam condenser receives 10 kg per second of steam with an enthalpy of 2570 KJ/kg. Steam condenses into liquid and leaves with an enthalpy of 160 KJ/kg, if cooling water passes through the condenser with temperature increases from 13oC to 24oC. Calculate the cooling water flow rate in kg/sec. Show conversion of units pls