A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 220.0 MPa.The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port ontothe vessel can safely withstand a force of 10.00 MN.pressure vesselboltsaloWArsideviewportCalculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm.cmx1ExplanationCheck2021 McGraw-Hill Education. All Rights Reserved. Terms of Use I Privacy AccessibilitylenovO.ddle WebEx at 3pm (dia just before 3pm)Resp1-650-479-3208Access Code (meeting Number): 737 129 915Dois!3134

Write the given values of this problem: Pressure(P)=220 MPForce(F)=10 MN

A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 220.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 10.00 MN. pressure vessel bolts side view port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm.

A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 220.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 10.00 MN. pressure vessel bolts side view port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm.

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter15: Fluid Mechanics

Section: Chapter Questions

Problem 9P: (a) Calculate the absolute pressure at an ocean depth of 1 000 m. Assume the density of seawater is...

See similar textbooks

Similar questions

A manometer is shown in Figure P15.36. Rank the pressures at the five locations indicated from highest to lowest. Indicate equal pressures, if any. FIGURE P15.36
You are pumping up a bicycle tire with a hand pump, the piston of which has a 2.00-cm radius. (a) What force in newtons must you exert to create a pressure of 6.90105 Pa (b) What is unreasonable about this (a) result? (c) Which premises are unreasonable or inconsistent?
A rock with a mass of 540 g in air is found to have an apparent mass of 342 g when submerged in water. (a) What mass of water is displaced? (b) What is the volume of the rock? (c) What is its average density? Is this consistent with the value for granite?
A mercury filled manometer with two unequal length arms of the same cross-sectional area is sealed off with the same pressure Po in the two arms (see figure below). With the temperature constant, an additional 10 cm³ of mercury is admitted through the valve at the bottom. The level on the left increases by 6 cm and the level on the right increases by 4 cm. Find the pressure Po. 50 cm Po WH Ø 30 cm
A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 150.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 2.80 MN. W 0 -pressure vessel cm bolts port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm. zide TO 0.P d 220
Assume patm = 1.00 atm....what is the gas pressure pgas? express answer in pascals to three sig figures...
The spring of the pressure gauge shown in the figure below has a force constant of 1 350 N/m, and the piston has a diameter of 1.40 cm. As the gauge is lowered into water in a lake, what change in depth causes the piston to move in by 0.700 cm? 4.635 X Your response differs from the correct answer by more than 10%. Double check your calculations. m Vacuum
The mercury sphygmomanometer shown in the figure below contains air at the cuff pressure P. Po h The difference in mercury heights between the left tube and the right tube is 102 mmHg systolic blood pressure P 0.102 m, a normal systolic reading. What is the gauge %3D %3D in pascals? The density of mercury is gauge p = 13.6 x 103 kg/m³ and the ambient pressure is Po = 1.01 x 105 Pa. %3D
A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will contain gases at pressures up to 230.0 MPa. The student's design calls for an observation port on the side of the vessel (see diagram below). The bolts that hold the cover of this port onto the vessel can safely withstand a force of 8.10 MN. W pressure vessel cm bolts side view port Calculate the maximum safe diameter w of the port. Round your answer to the nearest 0.1 cm. x10 X S ? do 18
Question 9 This question contains multiple parts. Make sure to read all the instructions and answer each part. spherical beach-ball of radius 20cm and average density 3kg/m³ is pushed downward under water at a constant speed of 1.62m/s to a depth of 2.21m below its starting point near the surface. ou may assume that the ball remains submerged the whole time, that it moves in the high Reynolds number regime with quadratic drag and that its drag coefficient is D≈ 0.5 Part a What is the work done by the force of gravity on the beachball during this process? Give your answer with the correct sign (positive or negative). Please enter a numerical answer below. Accepted formats are numbers or "e" based scientific notation e.g. 0.23, -2, 1e6, 5.23e-8 Enter answer here No answer submitted Part b What is the work done by the buoyant force during this process? Give your answer with the correct sign. Enter answer here No answer submitted Please enter a numerical answer below. Accepted formats are…
Draw diagrams and show complete answer. At 0 C the density of mercury is 13.595 x 10^3 kg/m^3. What is the height of the mercury column in a U-tube barometer if the pressure is 101.325kPa?
In figure below pressure gage A reads 1.5 kPa (gage). The fluids are at 20 °C. Determine the elevations z, in theopen piezometer tubes B and C.