A 5 gpm fixed displacement pump is used to extend a cylinder with a piston area of 2 in. Meter in speed control is used to limit the rod speed during extension to 10 fpm, and the pressure relief valve setting is 2000 psi. How much horsepower is wasted due to oil going over the pressure relief valve?

A 5 gpm fixed displacement pump is used to extend a cylinder with a piston area of 2 in. Meter in speed control is used to limit the rod speed during extension to 10 fpm, and the pressure relief valve setting is 2000 psi. How much horsepower is wasted due to oil going over the pressure relief valve?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylinder with a bore of 4.5 inches and a rod diameter of 1.5 inches is to be used in a system with a 6 GPM pump. What is the extension speed of the cylinder?
If the pump in Problem 7 has a displacement of 1.3 in.J/rev, what will the operatingspeed of the engine have to be?
A double-rod cylinder is one in which the rod extends out of the cylinder at both ends. Such a cylinder, with a 3-in diameter piston and 2-in-diameter rod, cycles through a 10-in stroke at 60 cycles per minute. What gpm size pump is required?
1. What is the power ratio of a pump and its 1/4 scale model if the ratio of the heads is 5:1? Select one: O a. 53.5 O b. 197 O c. 35.5 O d. 179
A regenerative circuit uses a cylinder with a 3 inch bore and a 1.84 inch rod. A pump is providing 8 gal/min of flow. What is the extension speed (in in/sec) of this cylinder?
1. A LEV system has a centrifugal fan rotating at 714 rpm. The airflow is 6210 cfm, the fan total pressure is 4.07” w.g., and the brake horsepower is 3.12 hp. If the rotating speed is decreased to 620 rpm, what are the brake horsepower? a. 1.43 hp b. 2.04 hp c. 2.41 hp d. 2.67 hp 2.A LEV system has a centrifugal fan rotating at 714 rpm. The airflow is 6210 cfm, the fan total pressure is 4.07” w.g., and the brake horsepower is 3.12 hp. If the rotating speed is decreased to 620 rpm, what are the new value for fan total pressure? 4.15" w.g. 3.87" w.g. 3.07" w.g. 3.94" w.g.
URGENT Please answer this problem in 30minutes. I need correct answers with complete and step by step solution. Box the final answers. Do not shortcut your solution. I will give an upvote if it satisfies. Thank you! If the velocity of water is 8 m/s and the pressure is 140 kPa on the discharge side of a pump. a. What is the head of the pump if the velocity is 4 m/s and the pressure is 90 kPa on the suction side of the pump? b. How much power is required to drive it if the diameter of the suction side is 600mm? c. If the pump is rated at 120hp, what is the efficiency of the pump neglecting energy losses in the system?
8. In the regenerative circuit shown below, the pump's flow rate is 10 gpm. If the piston diameter is 7 in and the rod diameter is 5 in (not a 2:1 cylinder), calculate the extension speed in in/min. Also calculate the oil flow rate at points A and B in gpm. (recall 1 gal = 231 in') PF The diagram above does not show a working regenerative circuit. What must be added in order for the circuit to be practical and why?
Draw the different cases for the inlet and outlet velocity triangle for centrifugal compressor. Also draw the velocity triangle centrifugal compressor with consideration of the slip.
Pumps are rated by its maximum O a. Operating pressure and output flow only O b. pressure and speed only O C. pressure, speed and flow. O d. output flow and speed in rpm only
If we assume that a given pump requires 7.50 ft of NPSH when operating at 3500 rpm, what would be the NPSH required at 2850 rpm?
What is performance characteristics of a centrifugal pump