6.100 A 0.25-m-wide billet of 5052-O aluminum (K = 210 MPa, n = 0.13) is forged from a thickness of 30 mm to a thickness of 20 mm with a long die with a width of 75 mm. The coefficient of friction for the die/workpiece interface is 0.25. Calculate the maximum die pressure and required forging force.

6.100 A 0.25-m-wide billet of 5052-O aluminum (K = 210 MPa, n = 0.13) is forged from a thickness of 30 mm to a thickness of 20 mm with a long die with a width of 75 mm. The coefficient of friction for the die/workpiece interface is 0.25. Calculate the maximum die pressure and required forging force.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A solid piece of steel 60 mm in diameter and 80 mm height is reduced in height by 50 percent with the help of open die forging. The work material characteristics are represented by k = 350MPA and n = 0.16. If coefficient of friction is 0.1, find the %3D maximum forging force.
Calculate (1) die pressure distribution and (2) forging force for plane strain forging (open die forging). Assume yield strength of the material is Y, and yielding criterion is von Mises. ho 2Lo h Forged to 2L xdx L 'x+value Note: Assume Zo Constant Plane strain Die pressure distribution h L L Die pressure distribution h MATERIAL L dx -(-1) Friction Hill Y L When 0; =Y P=Y' = Calculate forging force X L dF elemental volume Average pressure
A solid cylindrical slug made of 304 stainless steel is 150 mm in diameter and 100 mm high. It is reduced in height by 50% at room temperature by opendie forging with flat dies. Assuming that the coefficient of friction is 0.2 and the flow stress of this material is 1000 MPa, calculate the forging force at the end of the stroke. Manufacturing processes
A steel billet with a rectangular cross section is being forged using a die with a width of 84.5 mm. The billet has an original thickness of 46.0 mm and a width of 273 mm. The billet is upset to a thickness of 28.0 mm and the coefficient of friction for the workpiece-die interface is 0.234. Take the strength coefficient (K) as 526 MPa and the strain-hardening exponent (n) as 0.225. a) Determine the maximum die pressure (do not use average pressure formula). Expected answer: 1050 MPa b) Determine the required forging force (use average pressure). Expected answer: 16200000 N
A rectangufar workpiece has the following original dimensions: 2a = 120 mm, h = 40 mm and width = 25 mm (see Fig. 6.5). The metal has a strength coefficient of 530 MPa and a strain hardening exponent of 0.26. It is being forged in-plane strain with u = 0.25. Calculate the force required at a reduction of 25%. Use the average- Question 2 Not yet answered Marked out of 5 pressure formula. P Flag question
A compound die will be used to blank and punch a large rectangle (90x150mm blank dimensions) out of 6061ST aluminum alloy sheet stock 3.5 mm thick. The diameter of inside hole is 25 mm. The aluminum sheet metal has a tensile strength 310 MPa. Determine the minimum tonnage press (force) to perform the blanking and punching operation (1) assume that blanking and punching occur simultaneously and (2) assume that punching occurs first, then blanking, Take: Ac-0.06
Wire is drawn through a draw die with entrance angle a= 17°. Starting diameter is 3.0 mm and final diameter = 2.4 mm. The coefficient of friction at the work-die interface = 0.08. The metal has a strength coefficient K = 205 MPa and a strain-hardening exponent n = draw force in this operation. Why are multiple passes usually required to achieve the desired reduction? (Hint: Observe the draw stress value found in this question) 0.20. Determine the draw stress and Lubricant box Initial wire stock (in coil form) Multiple pass/draft drawing Draw die V2, F V3, F shown in figure. Capstan drum (holds multiple loops of wire) (1) (2) (3)
A cylindrical ingot with D0 = 50 mm and h0 = 40 mm is cold forged using an open die.The final height is 20 mm. The coefficient of form / friction between the die and the workpiece isconsider Kf = 1.10.The material from which the ingot is made has the following characteristics:K = 600 MPa and η = 0.12.Determine the force (F) on the operation:a) Force required at the moment of reaching the yield point (ℇ = 0.002)b) Force required when you have a height of h = 30 mmc) Force required when there is a final height of h = 20 mmd) Construct the graphs: Force vs Δh and effort vs Δh
Please give me full explanation in 1hour do it fast A 4-in-thick aluminum slab is 10 in wide and 100 in long. It is reduced in one pass in a two-high rolling mill to a thickness = 3.5 in. The roll rotates at a speed = 12 rev/min and has a radius = 20 in. The aluminum has a strength coefficient = 25,000 lb/in2 and a strain hardening exponent = 0.20. Determine the (a) roll force, (b) roll torque, and (c) power required to accomplish this operation, d) Estimate the GHG emission in an hour for the rolling operation.
The team performs a cold heading operation to produce the head on a steel nail. The strength coefficient for this steel is K = 550 MPa, and the strain hardening exponent n = 0.24. Coefficient of friction at the die- work interface = 0.10. The wire stock out of which the nail is made is 4.75 mm in diameter. The head is to have a diameter = 9.5 mm and a thickness = 1.5 mm. (a) What length of stock must project out of the die in order to provide sufficient volume of material for this upsetting operation? (b) Compute the maximum force that the punch must apply to form the head in this open-die operation. Discuss the result?
A small connecting rod is forged from AISI 1015 steel at 1200oC. Calculate the forging force in a mechanical press at a speed of 200 mm / s when the die comes into contact with the part. The volume of the connecting rod is estimated to be 28680 mm3, and 20% of the starting material is expected to burn off as flash (flash). In the final form the projected area is 3500 mm2 without flash. The width of the flash is 7.6mm around 300mm in circumference.
In a stamping operation, a 2 mm thick stainless steel sheet with an ultimate tensile strenght of 900 MPa is used. For a given blank size of 200 mm x 200 mm, calculate the punching force required to make a sheet metal part with 20 circle holes, each 4 mm and 10 square holes each with an edge of 5 mm. (1)