4. With reference to the Paschen curve below, Breakdown voltage (V) 60 55 50 45 40 35 30 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 pd (cm-torr) If a discharge at p = 0.1 torr, d = 20 cm is to be initiated, what is the voltage required to cause a breakdown? What will be the breakdown voltage if p = 0.025 torr, d= 20 cm?

4. With reference to the Paschen curve below, Breakdown voltage (V) 60 55 50 45 40 35 30 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 pd (cm-torr) If a discharge at p = 0.1 torr, d = 20 cm is to be initiated, what is the voltage required to cause a breakdown? What will be the breakdown voltage if p = 0.025 torr, d= 20 cm?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.21MCQ

See similar textbooks

Similar questions

Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
In the circuit of the following figure, the input voltage Vs is 15 volts rms with a frequency of 60 Hz, R equals 150 Ohms and C equals 100,000 Pico Farads. The diodes are Germanium (Vd = 0.2 volts) and the Zener diode is 12 volts. a) The magnitude of the ripple voltage at Cb) The Magnitude of the Peak Inverse Voltage (PIV) for D1 and D2.
A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100 sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816
In the circuit of figure Nº A, the secondary voltage Vs is 15 volts rms with a frequency of 60 Hz, R equal to 100 Ohms and C equal to 1000 microfarads. The diodes are silicon (Vd = 0.7 volts) and the Zener diode is 15 volts. Determine:a) The magnitude of the ripple voltage at Cb) The Magnitude of the Peak Inverse Voltage (PIV) for D1 and D2
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D IN4001 R 10 kn IN4001
For the given circuit below, a step down transformer gives an RMS voltage of 230 V/ 10.2-0-10.2 V with a load resistance of 2.2 Kiloohms. Assume Silicon diodes are used. Determine the Peak Inverse Voltage of the diode. D, SCT RL D. llle ண
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D1 IN4001 R. V out OV 10 kN D2 IN4001 llle
The ripple factor for pure dc is Answer: For the given circuit below, it operates on a peak-to-peak input voltage of 390.1 V, F= 60 Hz household supply through a step-down transformer with turns N1 = 10 and N2 = 1. Silicon diodes are used with a 1 Kiloohms load. Determine the output peak voltage (in volts). D1, D2 AC Input Vsec (Source) .03 D4 Load O 27.31 O 18.11 O 13.93 O 20.91
Which of the following statement is true? a. Angle between load voltage and load current in a pure capacitive load is 45 degree. b. Angle between load voltage and load current in a pure capacitive load is is 180 degree. c. Angle between load voltage and load current in a pure capacitive load is is zero. d. Angle between load voltage and load current in a pure capacitive load is is 90 degree.
Design of a DC-DC Converter. The Circuit Below shows a basic Buck-Boost Converter with a highly inductive Load. With a Deliberate mistake in the configuration of the Circuit Connection. The Value of L1 is 22mH, C1 is 10uF, R1 is 220 and L2 is 10mH. The circuit operates with a switching frequency of 20KHZ. The Duty cycle of the Clock signal V2 is given by the function below: ( 17 ) х0.2 Duty Cycle, k = 0. 55 + 100 Your Unique Duty Cycle = %3D Buck-Boost Converter Q1 IRG4BC10U D1 R1 222 1N4009 C1 LV1 12V L1 22mH 10µF L2 10mH a) Find the mistake in the configuration of the circuit and correct the connection error.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D1 IN4001 RL out OV 10 kN IN4001 alll
For the circuit in the figurea) Determine the time constant.b) Write the mathematical expression for IL, VL and VR, after the switch is closed.c) Determine IL, VL for one, three and five time constants.d) Draw the waveforms of IL, VL and VR.