4. Four identical SRS arms are grasping a common object as shown below. Spherical Joint Revolute Joint Find the number of degrees of freedom of this system while the grippers hold the object rigidly (no relative motion between the object and the last links of the SRS arms). Your answer should be an integer. Enter answer here 5. Referring back to Question 4, suppose there are now a total of n such arms grasping the object. What is the number of degrees of freedom of this system? Your answer should be a mathematical expression including 7. Examples of mathematical expressions including 7 are 4-n-7 orn/3.

4. Four identical SRS arms are grasping a common object as shown below. Spherical Joint Revolute Joint Find the number of degrees of freedom of this system while the grippers hold the object rigidly (no relative motion between the object and the last links of the SRS arms). Your answer should be an integer. Enter answer here 5. Referring back to Question 4, suppose there are now a total of n such arms grasping the object. What is the number of degrees of freedom of this system? Your answer should be a mathematical expression including 7. Examples of mathematical expressions including 7 are 4-n-7 orn/3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

B3. SOLVE STEP BY STEP IN DIGITAL FORMAT A set of sprockets is constructed, as shown in Figure 1, so that the second and third rotate on a common axis. When the first rotates, it drives the second and this in turn drives the third. Let and be the numbers of revolutions per minute of the first, second, and third axes. dy du dy dy dtu Find www.du' dx' and, and verify that dr du Figure 1 |1cm axis 1 |- 4cm -| axis 2 axis 1: y rev per minute axis 2: u rev per minute axis 3: x rev per minute |1e| |- 3cm-|| axis 3
For the 3-DOF Industrial manipulator arm as shown in Figure 3, determine the joint displacements for known position and orientation of the end of the arm point. 0. 0. Y1A Y2 A Y3 X2 X3 21 22 23 Yo xo Figure 3. 3 DOF RRR Industrial manipulator arm The link transformation matrices are given by C3 -S3 0 a3C3 S3 C3 1 C2 -S2 0 a,C2 C1 S1 -S1 -C1 d1 S2 C2 2T3 %3D T2 1 1 1 1 1 S1 C\C2a3+C1a2 C1C2C3 – C1S2S3 -C¡C2S3 – C1S2S3 S,C2C3 – S1S2S3 -SĄC2S3 – S1 S2C3 -C1 SịC2a3+ Sja2 Szaz + d1 1 OT3 = = °T, 'T2 ?T3 S½C3 + C2S3 - S2S3 + C2C3
A crank-rocker mechanism is to be used to drive a ratchet mechanism. Using mathematics and specific illustrations, find the required crank length in inches required to generate this motion. The swing of the rocker is 35.0 from the vertical position in each direction. (Note: O2 is the crank pivot; O4 is the rocker pivot; C is the coupler-rocker joint; B is the coupler-crank joint). O2O4: 5.6 in.; lies in the horizontal plane O4C: 4.0 in.; mid stroke is vertical
Find the value of the determinant D given by: a b 3 D = c d -4 6 9 9 where a = 2, b = 4, c = 9, d = 13 Give your answer as an integer.
Q3: Write two G-code programs using the following figure where units are in inches. a. The first program should use absolute positioning, and b. the second program should use incremental positioning. P4 Finish (6, 4) P2 (1, 3) P3 (4.79, 2) P1 Start (-2, 1) Center (2.5, 1) -2
Consider the figure as shown below. O-XoYoZo is the reference frame and O-X₁Y₁Z₁ is the frame attached to the tool. Sketch the tool position after each intermediate position of the operation of the tool about the reference frame: roll π/2(rotate about Zo), pitch -T/2(rotate about Yo), yaw π/2(rotate about Xo). Please write the final rotation matrix expression. ZI,Zo XI,Xo Yı, Yo
Please Draw The Freebody On a sheet of paper Only and Solve via Handwritten Only. Here I am facing difficulty in Typed based solution. [Reaction(N) and angle(°)]
5. A leg is placed in traction to keep it elevated and prevent it from moving as shown: Small pulley i. What is the tension in the rope (recall: 30.0 one rope gliding through pulleys will have the same tension throughout)? 30.0 m=250 kg ii. With what is force , F, that is acting to pull on the foot and keep the leg under tension? Construct a vector diagram to assist with your solution.
3 25 cm B P 25 cm A 25 cm 03 04 02 10 cm (crank) 20 cm FIGURE 1. Hoeken's linkage (a) Solve for 03 and 04 if the crank angle 02 = 120°. Show your work. (You may want to use the scripts to verify your answers.) (b) Find the position of point P when the crank angle is at 60 degrees.
In Part B, it was shown that the tension in a cable is constant around a frictionless pulley. The reason why the equations of equilibrium could be used here is because the values of 0 and o are not arbitrary. In fact, the geometry of the system is based on the equations of equilibrium and a relationship between 0 and o can be determined using them. Part D - Finding the relationship between \theta and \phi Figure Find the relationship between angles e and o using the equations of equilibrium and solve for 0. Suppose that the angles are expressed in radians. Express your equation for 0 in terms of ø. Express your answer in radians. • View Available Hint(s) Vol AEo t vec В A C Submit
Topic: Matrix and Determinants Subject: Advance Engineering Math Using the equations of equilibrium (EoE), obtain the system of equations and solve the forces F1, F2, F3 (in Newtons) using matrices.
A crank-rocker mechanism is to be used to drive a ratchet mechanism. Using mathematics and specific illustrations, find the required coupler length in inches required to generate this motion. The swing of the rocker is 35.0 from the vertical position in each direction. (Note: O2 is the crank pivot; O4 is the rocker pivot; C is the coupler-rocker joint; B is the coupler-crank joint). O2O4: 4.1 in.; lies in the horizontal plane O4C: 4.8 in.; mid stroke is vertical