►2/29 The unstretched length of the spring is r. When pin P is in an arbitrary position 6, determine the x- and y-components of the force which the spring exerts on the pin. Evaluate your general expressions for r = 400 mm, k = 1.4 kN/m, and 0 = 40°. (Note: The force in a spring is given by F = kô, where ô is the extension from the unstretched length.) L. 2 Problem 2/29

►2/29 The unstretched length of the spring is r. When pin P is in an arbitrary position 6, determine the x- and y-components of the force which the spring exerts on the pin. Evaluate your general expressions for r = 400 mm, k = 1.4 kN/m, and 0 = 40°. (Note: The force in a spring is given by F = kô, where ô is the extension from the unstretched length.) L. 2 Problem 2/29

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Equilibrium of Concurrent Force System. The piston of a reciprocating engine exerts a force of 175 kN on the crosshead when the crank is 45° (angle B) past TDC. If the stroke of the piston is 800 mm and the length of the connecting rod is 1.80 m, find the guide force and the force in the connecting rod. Hint: 1=½ stroke; Angle o may be solved using Sine Law in AACO. K= Compressive Force in the connecting Rod E= Piston Effort 70 120 F, = Guide Force Fig. P-1 Fig. P-2 a Tools: EF cos0=0; F sin .=0. R = Ev)* + (E#): ; R 771 =- : tane = sin A sin B sin C
Question 2: The ideal spring of constant k-2.6 kN/m is attached to the disk at point A and the end fitting at point B, as shown. The spring is unstretched when OA and Oв are both zero. If the disk is rotated 15° clockwise and the end fitting is rotated 30°counterclockwise, determine the vector expression for the spring force F. Determine distance C so that the moment the spring force makes about the Z axis is equal to 10.82 N.m. - A = 15°1 A 250 mm lllllll 900 mm k = 2.6 kN/m OB = 30° B G 200 mm
Question 2: The ideal spring of constant k-2.6 kN/m is attached to the disk at point A and the end fitting at point B, as shown. The spring is unstretched when OA and Oв are both zero. If the disk is rotated 15° clockwise and the end fitting is rotated 30°counterclockwise, determine the vector expression for the spring force F. ( Determine distance C so that the moment the spring force makes about the Z axis is equal to 10.82 N.m. ( A = 15°. C A 250 mm eeeeeee 900 mm k= 2.6 kN/m OB = 30° B LC 7-y 200 mm
The weight of the limb is W=15 lbs.The contact of foot with the ground can be modeled as a pin/hinge here. Determine the reaction force of the ground and the reaction at the knee joint and its direction/angle θ. Note: use the thee force member condition to find the angle of FK.Q4.As it’s been shown in the below figure,a person is using an exercise machine. Points A and B correspond to the shoulder and elbow joints, respectively. Relative to the person, the upper arm (AB) is extended toward the left (x-direction) and the lower arm (BC) is extended forward (z-direction). At this instant, the person is holding a handle that is connected by a cable to a suspending weight. The weight applies an upward (in the y-direction) force with magnitude F on the arm at point C. The lengths of the upper arm and lower arm are AB̅̅̅̅= 20cm and BC̅̅̅̅= 25cm, respectively, and the magnitude of the applied force is F = 400 N.Determine the components of reaction developed at the shoulder joint A When the…
Problem 2-16 Resolve the force Fzinto components acting along the u and v axes and detemine the magnitudes of the components. Given: F1 = 250 N F2 = 150 N e1 = 30 deg 82 = 30 deg 8z = 105 deg
The 300kn sphere is supported by a pull p and a 200kn weight passing over a frictionless pulley. If a=30°. Computer the value of p and tangent.
Determine the resultant of all parallel forces acting on the rocker arm. 4 ft 5 ft Select the correct response: 7 ft 50 lb 6 ft 4' 40 lb 20 lb 2' 3' 5' 60 lb
Determine the equivalent spring stiffness of the system using the displacement of the block as the generalized coordinate
3/34 Calculate the magnitude of the force supported by the pin at C under the action of the 900-N load ap- plied to the bracket. Neglect friction in the slot. B 45° 30 900 N 15° A 75 mm 150 mm Problem 3/34
For the spring assemblage shown below, determine the displacement at node 2 and the forces in each spring element. Also determine the force F3. Given: Node 3 displaces an amount 8 = 12.5 mm in the positive x direction because of the force F3 and k1 k2 175 kN/m.
5. The figure below represents the anatomy of the lower limb when balanced on your toes and the body weight acts through the tibia. The Achilles Tendon makes an angle (0) of 8° with the vertical and for this foot x1 is 6.2 cm and x2 is 12.3 cm. Calf Muscle Tibia Achilles Tendon Calculate the tension (T) in the Achilles Tendon if a 70 kg man stands on the toes of both feet. Using the values in this example what is the mechanical advantage for this lever and describe what that means in terms of the efficiency of the lever.
FA K mm L mm- M mm The operation of the fuel pump for an automobile depends on the reciprocating action of the rocker arm ABC, which is pinned at B and is spring loaded at A and D. When the smooth cam C is in the position shown, determine the force acting on pin B along Y axis and input its absolute value. (If your answer is negative, input its positive value such as -17 --> 17) Use the followings; FA=57N FC=246N K=51mm M=12mm L=22mm O=35degrees