2) In the figure, the OA arm moves clockwise with a constant angular velocity a rad / s. The pin connection connected to point B moves freely on the OA rod and in the slide path expressed by the curved equation r = 200 (2 - cose). Calculate the velocity and acceleration of the ring connected to pin B for 0 = 0c. %3D a (rad/s) =7.5 , Oc (0) =137

2) In the figure, the OA arm moves clockwise with a constant angular velocity a rad / s. The pin connection connected to point B moves freely on the OA rod and in the slide path expressed by the curved equation r = 200 (2 - cose). Calculate the velocity and acceleration of the ring connected to pin B for 0 = 0c. %3D a (rad/s) =7.5 , Oc (0) =137

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find out the velocity of slider D and angular velocity of CD in the mechanism shown below. Take Q1A= Q2B = 2cm; Q1Q2 = 4 cm; CD = 6 cm and wQ,A rad = 1 sec Solve using instantaneous center method. Use CCW direction. 20 QI 1 A Q2 20
Problem 7 (Use relative motion analysis): The four-bar linkage is a famous one! If the angular velocity and angular acceleration of the drive link OA are 10 rad/s and 5 rad/s², find the angular acceleration of bar AB at this position. Ans: %AB = -15.99 rad/s² B 200 mm CO 15⁰ 240 mm @0, %0 0 A 80 mm 60°
(Use relative motion analysis): The planetary gear system is used in car transmissions. There is sun gear S, planet gears P and the ring gear R. By locking (fixing/grounding) certain gears you can have different gear ratios and car speeds. = c) If the output shaft is held fixed, i.e. WA 0, and the ring gear is rotated at WR 5 rad/s, find the angular velocity, wp of = the planet gears and ws the sun gear. ως d) What if the planet gears are held fixed, Wp = 0 ? Шр WR R P WS 80 mm 40 mm 40 mm A
Bar AB is rotating about A with an angular velocity of wAB 2 rad/s counterclockwise. At this instant bar BC is horizontal. Find the Wac and also, velocity of collar C. Note. You must solve the problem in the way that we solved in the class. Use Vg VA+ wX TB/A and express the vectors in Cartesian vector form. Other solutions will not be evaluated. Solve the problem step by step, and clearly show your work. 25 35 mm 170 mm
5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angular velocity w and angular acceleration a (both counterclockwise). 6) if W = 5.3 rad/s and Q = 7.0 rad/s?, length I = 1.8 m, and angle 0= 36°, what is the angular acceleration of link AB in rad/s?? Please pay attention: the numbers may change since they are randomized. Negative must be included if it is clockwise. Your answer must include 2 places after the decimal point. 0.5 m O, a
Q1. Member AB is rotating (about fixed point A) with angular velocity (@ = 1 rad/sec) and angular acceleration (a = 2 rad/sec?) and driving the link CD (rotating about fixed point D at constant velocity) as shown in figure. Select five right answers. (a) Tangential Acceleration (a:) of link AB will not be zero (b) Tangential Acceleration (a) of link AB will be zero D 450mm (c) Tangential Acceleration (a,) of link CD will not be zero 200 mm 100 mm 60 H (d) Tangential Acceleration (a,) of link CD will be zero (e) All points on link CB will have same linear velocity 0 All points on link CB will have same angular velocity Formula • Tangential acceleration of a rotating link -ra • Radial (normal) acceleration of a rotating link = v³ /r= wr velocity of a rotating Ink (v) = r.w (g) Angular acceleration (a) for link CD will be zero (h) Angular acceleration (a) for link CB will not be zero Q2. Magnitude of linear velocity of any point “H" located at the half of the length of a rotating link CB…
For the linkage shown in the figure, using the graphyical velocity analysis method find the angular velocities of links 3, 4 and 5, and the linear velocity of of point D. The angular velocity of link 2 is 10 rad/sec ccw. Draw the accelaration diagram and calculate the angular accelerations of links 3, 4 and 5 and the linear accelartaion of the piston at point D. All dimensions are given in cms. Use velocity scale: 1 cm: 20 cm/s Use accelaration scale: 1 cm: 200 cm/s^2 28 42=12 L3=24 L5=24 04B=18 04C=18 02 X A 19 46.5
The crank OA of the mechanism shown in Figure 1 rotates uniformly at 180 r.p.m. in clockwise direction. The various lengths on the mechanism are: Table 1: The lengths of the mechanism OA AB 150 mm 450 mm TEATT PB 240 mm 1.1. Use vector diagram to calculate the velocity of Piston D. 1.2. Calculate the accelerations of Piston D. 420 300 I 150 ammmwrin BC 210 mm B O 30° Figure 1: All dimensions in the mechanism are in mm CD 660 mm
For the Mechanism shown, find the acceleration of the slider link4 using Vector loop method. Assume r3=1 cm. Y B KE 13 =90°. 00₂= 10 rad/s CCW (constant) X Hand written plz a
5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angular velocity W and angular acceleration a (both counterclockwise). 6) if W = 4.4 rad/s and a = 7.7 rad/s2, length I = 1.7 m, and angle 0= 27°, what is the angular acceleration of link AB in rad/s2? Please pay attention: the numbers may change since they are randomized. Negative must be included if it is clockwise. Your answer must include 2 places after the decimal point. 0.5 m A 0, a B Your Answer: Answer
5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angular velocity W and angular acceleration a (both counterclockwise). 2) if W = 4.2 rad/s and a = 8.0 rad/s2, what is the magnitude of the linear velocity of point A? Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper unit. 0.5 m A 0, a B Your Answer: Answer units
Motor is driving a gear attached to the linkage in the mechanism as shown: Let r₁ r₂ = 10mm; c= 22mm; b= 100mm; a = 3mm; Determine the functions , of velocity of the slider with parameters (a,b,c) using the vector approach. (Hint: gears do not slip, link o-D is attached rigidly to the gear, pins at E and D allow free rotation) Schematic of kinematics: Velocity vector of point D: Velocity vector of point E: Equation of Velocity for the link E to F: b r₁ 12 Wm