1500 KN 800 mm 70 mm 100 mm 1500 KN A bar has a length of 800 mm, width 100 mm, and thickness 70 mm, and is being subjected to 1500 KN of tension as shown. As a result, the length of the bar as increased to 802.5 mm and its width has decreased to 99.906 mm. Assume elastic behavior. a) Determine the Young's modulus (E) of the material b) Determine the Poisson's ratio (v) of the material c) Determine the Shear modulus (G) of the material d) Determine the new thickness of the bar in mm e) Determine the percentage change in the total volume of the bar

1500 KN 800 mm 70 mm 100 mm 1500 KN A bar has a length of 800 mm, width 100 mm, and thickness 70 mm, and is being subjected to 1500 KN of tension as shown. As a result, the length of the bar as increased to 802.5 mm and its width has decreased to 99.906 mm. Assume elastic behavior. a) Determine the Young's modulus (E) of the material b) Determine the Poisson's ratio (v) of the material c) Determine the Shear modulus (G) of the material d) Determine the new thickness of the bar in mm e) Determine the percentage change in the total volume of the bar

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a = 450 mm t = 20 mm Op b= 350 mm The plate shown in the figure is made of a material having a modulus of elasticity of 200 GPa and Poisson's ratio of 0.2. The plate is under the effect of normal stresses oą and op. The magnitude of oą is 150 MPa. If the final thickness of the plate is known to be 20.001 mm under the applied stresess; determine the magnitude of op. Express your answer in MPa and round it to the nearest integer if necessary.
A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial load of P = 31,025 lb. produced a deformation of 0.115 inch over a gauge length of 2.10 inches and a decrease of 0.0080 inch in the 0.60-inch thickness of the bar. a. Determine the lateral strain. b. Determine the axial strain. c. Determine the Poisson’s ratio v. d. Determine the decrease in the 4.05-in. cross-sectional dimension (in inches).
In the figure, determine the normal stress and change in length of the aluminum rod if the temperature was raised by 126°C. The 0.5-mm gap exists at 25°C. 0.56 mm 366 mm 255 mm Aluminum A = 2TTT mm² E = 75 GPa x = 23 x 10*/°C B Stainless Steel A = 8QQ mm² E = 190 GPa α = 17.3 x 10/°℃
2. A copper rod of diameter 12 mm is subjected to a compressive force of 8 kN. The change in diameter happens to be 4.5 x 103 mm. Determine the strain along the length of the material and the Poisson's ratio when E = 110 GPa.
30. An aluminum alloy rod has a circular cross section with a diameter of 8mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E = 69 GPa. If Poisson's Ratio is 0.33, what will be the lateral strain? E= 6/8 v = -E(lateral)/(axial)
For a steel plate, whose length (along the y-direction) is very large compared to its width (along the x-direction), the deflected surface is assumed to be cylindrical; the axis of the cylinder is parallel to the length of the plate. At a certain point, the strain in the shorter direction was measured as 0.0066. Taking E =255 x 103 N/mm2, Poisson’s ratio n = 0.3; Calculate the stresses σx & σy.b) Explain why in-plane forces are neglected in the analysis of bending in thin plates
Q3 / An element in plane stress at the surface of a large machine is subjected to stresses shown below. Using Mohr's circle determine the following quantities (a) the principal stresses and their directions and (b) the maximum shearing stresses and the directions of the planes on which they occur. 100 MPa 50 MPa 75 MPa 75 MPa 50 MPa 100 MPa
3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 13.05 ksi, or in bronze of 100 MРа. Aluminum A = 400 mm Bronze A = 200 mm Steel A = 500 mm? 2P 4P 2.5 m 2.0 m 1.5 m
A square plate of width b and thickness t is loaded by normal forces P, and Py, and by shear forces V, as shown in the figure. Assume that the material is linearly elastic with modulus of elasticity E and Poisson's ratio v. These forces produce uniformly distributed stresses acting on the side faces of the place. The dimensions for an aluminum plate are b = 10 in., t = 0.75 in., E = 10,600 ksi, v = 0.33, P, = 96 k, Py = 24 k, V = 18 k, Px (a) Calculate the change AV in the volume of the plate. (Round your answer to four decimal places) AV = in.3 Calculate the strain energy U stored in the plate. (Round your answer to the nearest whole number) V = in.-lb (b) Find the maximum permissible thickness of the plate when the strain energy U must be at least 640 lb-in. (Assume that all other numerical values in part (a) are unchanged). (Round your answer to three decimal places) t = in. (C) Find the minimum width b of the square plate of thicknesst = 0.75 in. when the change in volume of the…
Steel cylinder has 200 mm mean diameter with a wall 1 mm thick and 310 mm long. Determine the circumferential and longitudinal stresses that occur on the cylinder if the maximum pressure difference allowed between the inside and outside must not exceed 100 MPa. Determine the effects of three dimensional loading by determine volumetric strain and change in volume for the first steel cylinder. Modulus of elasticity E= (210 GPa), Poisson's ratio 0.30. 7
A bar made from aluminum (E = 72 GPa) has a diameter of 12 mm. When the bar is subjected to a tensile axial force P, its diameter is decreased by 0.018 mm. Assume the Poisson’s ratio to be 0.33. Determine the value of loads P and its axial deformation. P = ? N δ = ? mm
An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure. Determine the change of length of diagonal BD. 120mm 120 MPa 160mm , 100мра C 240 MPa E=80GPa ✓=0.3 G=30GPa Answer = -0.5888mm