eBrandon ReardonName1. The lap joint shown is connected by four 20-mm diameter rivets. The load P is equal to 120 kN andis carried equally by the four rivets.How many shear planes are there?b. Determine the shear stress in the rivets in MPa.P=120 KNa.160 mm |mm12 mmA tie rod of 4 inch diameter is used to hold a plaster wall in place. The tensile stress in the rodcaused by load P is 20 ksi. Find the diameter "d" (to the nearest 1/6 inch) of the washer that keepthe bearing stress between the plaster and the washer from exceeding 300 psi.2.WallTie rod

Answered: Image /qna-images/answer/886c05f9-a93a-47d4-9a5b-a98c6ac7f35a.jpg

1. The lap joint shown is connected by four 20-mm diameter rivets. The load P is equal to 120 kN and is carried equally by the four rivets. P= 120 KN a. How many shear planes are there? b. Determine the shear stress in the rivets in MPa. 12 mm 12 mm

1. The lap joint shown is connected by four 20-mm diameter rivets. The load P is equal to 120 kN and is carried equally by the four rivets. P= 120 KN a. How many shear planes are there? b. Determine the shear stress in the rivets in MPa. 12 mm 12 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The cross-sectional area shown is subjected to V = 600 kN and M =1000 kN-m. What is the transverse…

Q: A concentrated load of P = 19 kN is applied to the upper end of a pipe with length L = 5 m. The…

Q: The lap joint shown is fastened by five % inch-diameter rivets. The bearing stress in the plates is…

Q: The segments AB and BC of composite bar constructed of the same steel have identical crosS-sectional…

Q: 1.25 The piece of wood, 100 mm by 100 mm in cross section, contains a glued joint inclined at the…

A: Given data: The area of a cross section of wood, A = 100 mm by 100 mm. The stress for tension, σt =…

Q: 1.14 A steel sleeve of 24-mm internal diameter and 36-mm external diameter 0.4 mm encloses an…

A: Given : di=24 mmdo=36 mmd=22 mmlsleeve=400 mmlrod=0.4 mmEa=75 GPaEs=205 GPa

Q: Two plate are joint by three rivets of 15 mm diameter. What is the shear stress in the material if…

A: For solution refer below images.

Q: 1. 2nd A -steel +p=60 kN

A: Given data Aluminum tube AB is fixed on support A, and the load P=60 KN is applied on Steel rod BC…

Q: wo 6-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto the…

A: Given:Shear strength, τ=120 psiForce applied, P=10000 lbGap=0.5 inwidth, w=6 in

Q: A rectangular beam is 12 meters long. It is supported by R1 at the left end and R2, 4 meters from…

A: Solution is given below:

Q: The lap joint shown is fastened by 4 rivets of ¾ in. diameter. Find the maximum load P that can be…

A: Given Data: Diameter of rivet, d=3/4 inch Working shear stress, 14000 psi Working bearing stress,…

Q: Assume that the axial load P applied to the lap joint is distributed equally among the three…

A: Answer: The maximum allowable value of load that can be applied on the joint is 37.7 kN.

Q: For the structure shown below, the shear stress in the pin at B is determined a MPa if it has a…

Q: Fig. 2, shows a cylindrical rod of 25 mm diameter, welded to a flat plate. The cylindrical fillet…

Q: Two bars are connected by means of a rivet of diameter 5 mm as shown in fig. below. Determine the…

Q: A cantilever beam, 100 mm wide by 270 mm high and 9 m long, carries a load that varies uniformly…

A: Given:b=100 mmd=270 mmL=9 mW=1300 N/m

Q: 4. The rigid slab is supported by two identical copper rods as shown. The copper rod has an area of…

A: Answer: (a) The stress in the aluminum rod: 16.80 MPa. (b) The stress in the copper rod: 6.71 MPa.

Q: 1. In the figure, assume that a 20-mm diameter rivet joins the plates which are 100 mm wide. a. If…

A: P= Stress x Arivets P=80[1/4 π (202)] P=8000 π N From bearing of plate material:P=σbAb 8000 π = 140…

Q: For the connection shown, the bolt diameter is d = 30 mm. The average shear stress in the bolts…

Q: The allowable stresses for the splice shown are the following: 150 MPa for shear of rivets, 1.35Fy…

A: Given Dataσs=150MPaFy=250MPat=20mmw=300mmσt=0.6Fy=150MPa

Q: 20 KN it 80 Q3/ A bracket is supported using 4 rivets having same size, as shown in Figure 3.…

Q: For the connection shown, the bolt diameter is d = 20 mm. The average shear stress in the bolts must…

Q: Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if…

A: For solution refer below images.

Q: 1.14 A steel sleeve of 24-mm internal diameter and 36-mm external diameter 0.4 mm encloses an…

A: The internal diameter of the steel sleeve is d1=24 mm. The external diameter of the steel sleeve is…

Q: Two blocks of wood, width w and thickness t, are glued together along the joint inclined at the…

Q: A cantilever beam, 80 mm wide by 270O mm high and 8 m long, carries a load that varies uniformly…

A: Draw a diagram for the cantilever beam. Here, w1 is the load intensity at point B i.e. at 5 m from…

Q: Two 8-in-wide wooden boards are to be joined by splice plates that will be fully glued onto the…

A: Data given- P = 20000 lb a = 0.4 in Shear strength = 145 psi w = 8 in

Q: A single rivet is used to join two plates as shown. If the diameter of the rivet is 20 mm and load P…

A: Given, Applied force = P = 30 kN = 30,000 N Diameter of the rivet = d = 20 mm Hence,…

Q: The lap joint shown if Fig. is fastened by four 3/4 inch diameter rivets. Calculate the maximum safe…

Q: A steel bar with a rectangular cross section is used to transmit four axial loads as shown in Fig.…

A: Given: The force at point A is FA = 35 kip. The force at point B is P. The force at point C is FC =…

Q: 1.4 Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly…

A: To determine the stress in each segment.

Q: 100 N K 250 N 200 N 50 N No 500 mm 400 mm 1700 mm

A: Given; E=200 GPa=200000 MPaA =25 mm2

Q: Two blocks of wood, 50 mm wide and 20 mm thick, are glued together as shown in figure below. Using…

Q: Example 3 Determine: a. The shear stress at point B on the web of the cantilevered strut at section…

A: Answer: (a) The shear stress at point B: 8.81735 MPa (b) The maximum shear stress: 9.70434 MPa

Q: 2. A square aluminum bar should not stretch more than 1.4 mm when it is subjected to a tensile load.…

Q: Question 2. Design of the riveted joint of a structure, draw a designed sketch. Two parts having…

A: Given: Butt joint is made with the help of rivets Permissible stress in tension = σt MPaPermissible…

Q: 1.4 (A). Two fork-end pieces are to be joined together by a single steel pin of 25mm diameter and…

A: Given, d=25 mmP=50 kN=50×103 Nτmax=180 MN/m2=180×106 N/m2

Q: For the connection shown in the figure, determine the average shear stress (psi) produced in the…

A: ◆ The average shear stress produced in each of the bolt is 5660 psi. ◆ Therefore, option (b) is…

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

Q: A cantilever beam, 80 mm wide by 260 mm high and 9 m long, carries a load that varies uniformly from…

A: Width of the cantilever beam, B= 80 mm Height of the cantilever beam, H= 260 mm Length, L= 9 m At…

Q: If the wood joint in Figure has a thickness of 150 mm, determine the average shear stress along…

A: 2F = 6 ⇒F=3×N=Vb Therefore, Average shear stress along a-a plane =3×103150×100…

Q: 1- A torque of 600 N.m is applied to the rectangle section shown in fig . determine the wall…

A: As per given question T=600 N-m Length =60mm Breath=30mm Shear stress =60 mpa We Have to determine…

Q: Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution…

Q: Q1/ Find the value of P for the joint shown in the figure if the allowable shear stress is 100 MPa…

Q: Determine the largest weight of the picture frame that can be by the two ropes Tas shown in the…

Q: 30° P 10 in. B 12 in.

A: Apply Equilibrium Conditions to above fbd

Q: (2) Q1 what the value of P Which are safer on the rivets as shown in figure below. given that :…

Q: Two 8-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto the…

A: Given: Width of the wooden boards→w=8 in=0.66 ft Gap between the boards→a=0.6 in=0.05 ft Applied…

Q: A cantilever beam, 80 mm wide by 290 mm high and 9 m long, carries a load that varies uniformly from…

Q: 10 cm 600 N 14 cm B -- Vertical load is applied to point Bof a 10 mm radius cylindrical bar as shown…

A: Given data: Radius of the cylindrical bar is: r=10 mm which is fixed at point 'C'. We need to find…

Question

eBrandon Reardon
Name
1. The lap joint shown is connected by four 20-mm diameter rivets. The load P is equal to 120 kN and
is carried equally by the four rivets.
How many shear planes are there?
b. Determine the shear stress in the rivets in MPa.
P=120 KN
a.
160 mm |
mm
12 mm
A tie rod of 4 inch diameter is used to hold a plaster wall in place. The tensile stress in the rod
caused by load P is 20 ksi. Find the diameter "d" (to the nearest 1/6 inch) of the washer that keep
the bearing stress between the plaster and the washer from exceeding 300 psi.
2.
Wall
Tie rod

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The lap joint shown is fastened by five ¾ inch-diameter rivets. The bearing stress in the plates is limited to 10 ksi and the shearing stress in the rivets is 15 ksi. Assume the applied load is equally distributed among the five rivets. The thickness of each plate is ½ in. Calculate the load P based on each stress given. Determine the maximum safe load P that can be applied. Express the loads in kips.
1. A 60-mm diameter steel tube with a wall thickness of 3 mm just fits in a rigid hole. Determine the tangential stress developed if an axial compressive load of 12 kN is applied. Use v = 0.30 and E = 200 GPa. Answer: 0 = 6.37 MPa 2. A 200-mm long bronze tube closed at both ends fits without clearance in a 70-mm hole in a rigid block. It has a diameter of 70 mm and a wall thickness of 5 mm. The tube then sustained an internal pressure of 4.5 MPa. Use v = 0.33 and E= 83 GPa. Compute the tangential stress in the tube. Answer: Ot = 5.20 MPa
Q1/ Find the value of P for the joint shown in the figure if the allowable shear stress is 100 MPa for the rivets. The four rivets are equal, each of 20 mm diameter. | 100 100 200 600 All dimensions in mm.
2. Determine the shear, tensile and bearing stresses on a double riveted butt joint with ¾ in. main plates, 1/2 in. side plates, and 7/8-in.-diameter steel rivets. The connection is shown in Fig. 2. in in 40 000 lb P = 40 000 Ib 40 000 Ib 5 in 40 000 Ib -in Fig. 2.
The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the pin in psi if a load of P = 19616 lb is applied at A? The d = 0.65-in.-diameter pin is in double shear. Round off the final answer to two decimal places.
Q1/ A bracket is supported by means of 4 rivets of the same size. Design the 7. Alalkau diameter of the rivet if Ou (tenşile ultimate stress) for the rivet material is 560MPA. Which of the rivet has max resistance? 20KN 20KN B0mm 30 mm 30 mm 30 mm
1. A BRONZE ROD IS SUBJECTED TO A TENSILE LOAD OF 15,000N. IF ITS ALLOWABLE STRESS IS 75 MPa, CALCULATE THE OUTER LENGTH OF THE SIDE OF THE PENTAGONAL TUBE IF THE INNER LENGTH OF THE ONE SIDE IS 40mm. 15,000N 15,000N 40mm CROSS-SECTION OF THE BRONZE ROD BRONZE ROD
2. If the allowable shear stress for each of the steel pins at A and B is tpe 6.5 ksi and the allowable normal stress for bar CB is Operm 10 ksi, determine the diameter of the pins at A and B and that of the square bar CB. Pin A is in double shear while Pin B is in single shear. Ignore points D and E. (^ } 2.5 ft -3 ft -5 ft 150 lb/ft Fx =
Q1 / If the cross section of the femur can be approximated as a circular tube, determine the state of stresses on the points A and B at section due to the loads as shown in figure Q1. T. = 2 cm = 1.6 cm %3D Figure Q1 B L 20 cm
1.4 Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in cach material given that P = 10 kN? Bronze Aluminmım Steel A=400 mm2 2P A=600 mm A= 300 mm 3P 4P P m 5m- -4m-
NEED ANSWER ASAP THANK YOU !! A joint is made by gluing two plywood gussets of thickness t = 0.78 in to wood boards. Determine the shear stress for the glue (in psi) if the dimension b = 17.51 in and the applied force is P = 9857 lb. Round off the final answer to three decimal places.
A link is loaded as shown, it is attached with two bolts with a diameter of 0.25 in. The link width is 2 lh and its thickness is 0.1 in, if the average normal stress in the link is 20 ksi (away from the bolts) determine the applied force G, the shear stress of a bolt as well as the bearing stress in one of the bolt holes. 2 in G