1. Determine the area of reinforcing steel required for the T beam shown if concrete compressive strength is 28 MPa and steel yield strength = 420 MPa and modulus of elasticity of steel = 200,000 MPa. Check tensile strain to see that it is 0.005 effective width = 1600 mm H 300 mm M₂=475 kN m 100 mm 600 mm 500 mm

1. Determine the area of reinforcing steel required for the T beam shown if concrete compressive strength is 28 MPa and steel yield strength = 420 MPa and modulus of elasticity of steel = 200,000 MPa. Check tensile strain to see that it is 0.005 effective width = 1600 mm H 300 mm M₂=475 kN m 100 mm 600 mm 500 mm

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Similar questions

SIT. B: Determine the tensile steel ratio of a given conditions if concrete strength f'. = 28 MPa and steel yield strength fy 4. if the tensile strain is Es = fy/Es upon crushing of concrete at a strain of 0.003. C. 0.02833 A. 0.01567 B. 0.02161 D. 0.02125 if the tensile strain is limited to 0.004 upon crushing of concrete at a strain of 0.003. A. 0.01567 B. 0.01548 5. 6. Minimum as required by NSCP 2015. C. 0.00313 D. 0.00405 A. 0.00333 B. 0.00276 = 420 MPa. C. 0.02778 D. 0.02064 uniformly
'bd . As per IS 456:2000 for M20 grade concrete and plain barsin tension the design bond stress t= 1.2 MPa Further, IS 456:2000 permits this design bond stress value to be increased by 60% for HSD bars. The stress in the HSDreinforcing steel barsin tension, a MPa. Find the required development length, La for HSD barsin terms of the bar diameter, = 360 S o.
The flexural tensile strength of M25 grade of concrete, in N/mm², as per IS:456-2000 is A 0.5 B 5 C 2.25 D 3.5
If the compressive strength of the concrete is 4 ksi and the yield strength of steel is 60 ksi, the value of that should be used in computing the design moment strength oMn for the beam section should be 23.5 in 1.5424 0.65 0.48 0.9 3#9 14 in 26 in
Q4: For the RC beam section shown in figure below, find the location of neutral axis (N.A) and the stresses in concrete & steel reinforcement at tension and compression side. If concrete modulus of rupture (tensile strength) equals 10% of f'c, is it expected to crack at tension side? As (30 25 mm) = 1500 mm² f'c = 30 N/mm² fy = 420 N/mm² Es = 200000 N/mm² Ec= 20000 N/mm² 500 450 250
24 Calculate the tensile steel stress of 5-16-mm-dia rebars in a concrete beam 290 mm by 470 mm at ultimate stage if f'c = 27 MPa and fy = 420 MPa. Express your answer in whole number.
| Choose the most appropriate answer for the following: 3. Which one of the following is not categorized as a long-term loss of pre-stress in a pre-stressed concrete member? Loss due to elastic shortening b. Loss due to creep c. Loss due to shrinkage а. d. Loss due to relaxation of steel 4. One of the following is not correct for pre-stressed concrete: a. Reducing cracks in the concrete b. High strength of concrete and steel c. Costy d. Suitable for long span and those carrying heavy loads. 5. Cross ties are used if the distance between a bar and the corner bar is greater than... 100 inches b. 100 cm c. 150 inches d. 150 mm а.
Assuming the concrete is uncracked, compute the flexure stresses in the extreme fibers of the beam as shown in the figure for a bending moment of 34 kN-m. The concrete has an f' of 27.60 MPa; determine also the cracking moment of the section. (Use 0.62 1 = 0.70 in calculating the modulus of rupture). Dimensions are in millimeter. 380 455 3 #9 bars (A, = 3.00 in.2) 75 300
CASE:A rectangular beam has the dimensions (see Fig.1) b = 15 in.,h = 30 in., and d = 27.37 in. and is reinforced with three No.9 bars. The concrete compressive strength fc' is 4000 psi, and the tensile strength in bending (modulus of rupture) is 475 psi. The yield point of the steel fy is 60,000 psi, the stress-strain curves of the materials being those of Fig.2. Determine the stresses caused by a bending moment M = 45 ft-kips.Question1:Check this case, would the concrete of the beam crack? Please calculate the strengths of those two materials in this beam.Question2:Suppose the beam under this case is subject to a bending moment M = 110 ft-kips (rather than45ft-kips as previously). Calculate the relevant properties and stresses.Question3:Determine the nominal moment Mn at which the beam of this case will fail. Question4:Have a comparison of the calculation results with those of three questions.
9. If the value of the fc' of concrete is 30 MPa, and the actual stress of the concrete subjected to a force is 12 MPa, at what stage is the concrete at?
Why is reinforcing steel used in concrete? Discuss the typical properties ofreinforcing steel.
42. Permissible tensile strength of concrete, M150 is: A) 150kg/cm² C) 150N/mm² B) 15kg/cm D) 15N/mm2