1. A 300mm long composite bar is constructed by bonding an alloy steel outer sleeve of outside diameter 75 mm to a solid mild steel core of diameter 67 mm. A tensile force of 200kN was applied to the composite bar. If the modulus of elasticity for the mild steel is 208 GN/m² and that for the alloy steel is 360 GN/m². Determine the following values for the composite bar: Calculate: a) The stress in the mild steel core. a) The stress in the alloy steel sleeve. a) The extension under loading of the composite bar.

1. A 300mm long composite bar is constructed by bonding an alloy steel outer sleeve of outside diameter 75 mm to a solid mild steel core of diameter 67 mm. A tensile force of 200kN was applied to the composite bar. If the modulus of elasticity for the mild steel is 208 GN/m² and that for the alloy steel is 360 GN/m². Determine the following values for the composite bar: Calculate: a) The stress in the mild steel core. a) The stress in the alloy steel sleeve. a) The extension under loading of the composite bar.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.3P: A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the...

See similar textbooks

Similar questions

A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
(a) Solve part (a) of the preceding problem if the pressure is 8.5 psi, the diameter is 10 in., the wall thickness is 0,05 in., the modulus of elasticity is 200 psi, and Poisson's ratio is 0.48. (b) If the strain must be limited to 1.01, find the maximum acceptable inflation pressure
3. A mass of 102kg falls 12mm directly onto the end of a bar 25 mm in diameter and 1.5m long. If E for the material is 207 GPa, find the instantaneous stress produced.
An engineering machine component operating in a high temperature environment consists of a copper pipe having a cross-sectional area of 2 000 mm² and 0.3 m long, which is placed between two rigid caps. Four M22 steel bolts are symmetrically arranged around the tube and parallel to the axis of the tube and are lightly tightened. 3.1 Find the stress in the pipe and the bolts if the temperature of the assembly is increased from 25 °C to 95 °C. 3.2 What load will each bolt carry at the raised temperature? 3.3 Make a neat sketch of the assembly. (Est = 200 GPa, Ecu – 100 GPa, as: = 12 × 10-6/ °C, acu = 16 × 10-6/ °C)
A solid steel bar 250 mm long is 10 mm square over part of its length, the remainder being circular with a diameter of 25 mm. A gradually applied tensile load P kN induces a maximum stress in the bar of 200 MPa. The total strain energy in the bar when the stress of 200 MPa is acting is 1.3 J. Calculate '.1. The load P 1.2. The total extension of the bar .3 The length of the square portion of the bar 3.4 The suddenly applied load that will induce the same amount of energy .5 The load that falls from a height of 8 mm and induces 1.3 J in the bar (E = 200 GPa).