The nail cutter consists of the handle and the two cutting blades (Eigure 1) Figure 6 mm 6 mm -36 mm < 1 of 1 > F ▼ Part A Assuming the blades are pin connected at B and the surface at D is smooth, determine the normal force on the fingernail when a force F= 6.0 N is applied to the handles as shown. The pin AC slides through a smooth hole at A and is attached to the bottom member at C Express your answer to three significant figures and include the appropriate units. FN = Submit HA Value Provide Feedback Request Answer Units Next >

The nail cutter consists of the handle and the two cutting blades (Eigure 1) Figure 6 mm 6 mm -36 mm < 1 of 1 > F ▼ Part A Assuming the blades are pin connected at B and the surface at D is smooth, determine the normal force on the fingernail when a force F= 6.0 N is applied to the handles as shown. The pin AC slides through a smooth hole at A and is attached to the bottom member at C Express your answer to three significant figures and include the appropriate units. FN = Submit HA Value Provide Feedback Request Answer Units Next >

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.97P: The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces...

See similar textbooks

Similar questions

Determine the magnitude of the pin force A
Determine the force supported by the pin at A for an 80-N squeeze on the handles of the pliers. (Hint: Draw free body diagram of each handle) -35 mm- 95 mm- 80 N 80 N
This shoulder bolt is composed of hot-rolled monel. The head of the shoulder bolt is a regular hexagon and it measures 6 mm across opposite flats. The other dimensions of the bolt are given below, as well as the forces to which this component is subjected. Find the change in length of each segment of the part as well as the overall change in length from A to D F_A = 4.8 kN F_B = 5.1 kN F_C =1.6 kN F_D = 1.9 kN a = 4mm b = 4.1 cm c = 6.8 cm d_s = 5 mm d_t (effective) = 3mm Assume:∙ Bearing stress between threads of the bolt and the nut may be neglected∙ Stress concentration effects may be neglected∙ The force that the nut applies may be treated as a concentrated force.∙ The nut may be treated as rigid.∙ The forces applied to the nut and the shoulders of the bolt are distributed evenly around their perimeters δAB = δBC = δCD = δoverall =
Also draw the free body di
Determine the n- and t-components of the force F which is exerted by the rod AB on the crank OA. Evaluate your general expression for F = 84 N and (a) e = 30°, B = 25° and (b) e = 16°, B = 27° %3D F BI B L--n Answers: (a) Fn= N, F = N (b) Fn= N, F = the tolerance is +/-2%
1-63.M. The key in Figure 1-18 has the dimensions b = 10 min, h = 8 nim, and L = 22 min. Determine the shear stress in the key when 95 N-m of torque is transferred from the 35-mm-diameter shaft to the hub. Hub End view Shear plane Shear pl T=Torque -D=Shaft diameter T=F(D/2) F₁-Force of shaf F₂= Force of hub on 1 Shear area=A,=bxL
For the same question, the M25 Screw will be used when pressing the Nut Wheel onto the shaft. Assuming that the force that the nut needs to suppress is Fçak=1218 kgf (it was found in the previous question, but we don't use it), what should the minimum NUT HEIGHT be in mm to create this force safely? (Screw and Nut's surface safety pressure Pem=45 N/mm2 Screw base diameter d1= 21.5 mm. (Calculate the pitch (h=?) according to the given ones, considering that metric screw is used!)
Q1: The arrangement of a transmission brake is shown in the figure. The arms are pivoted at O and, when force is applied at the end of the hand lever, the screw AB will rotate. The left-and right- hand threads working in nuts on the ends of the arms will move the arms together and thus apply the brake actuating force equally. A B 12cm The drum is 17.75cm diameter, and the angle subtended by each block is 90°. the friction material lining width is 4cm. Assuming a coefficient of friction for the braking surfaces that is equal to 0.30 Determine the force required by the screw AB to set the brake torque on the drum equal to 200 N-m. 17 75cm 12cm 46 35cm Torqueleft= TorqueRight= 97.40 N.m 6 35cm 102.60 N.m
Draw the linkage to scale and graphically find the possible solutions (open and crossed) of 03 and 04. Determine the Grashof condition. Given Link, = 228.6 mm, Link2 = 177.8 mm, Link3 = 279.4mm, Linka = 152.4mm and 02= 120.
1 300N forces on the pliers? 300N What forces are exerted on the bolt at E in the figure below as a result of the 30 mm 70 mm PIED PAR 30 mm D 30 mm 30 mm
3. At temperature T₁, the two rigidly connected rods just fit the rigid supports. If both sections are identical except for the diameter, prove that the following equations are true when temperature rises to T₂. a. F= b. OAB C. OBC A x(T₂-T₁)лd²E 20 x(T₂-T₁)E 5 9x(T₂-T₁)E 5 -1/2- d B 1/12- d C
5-9 4) USE THE METHOD OF SECTIONS TO FIND THE MAGNITUDE AND DIRECTION OF THE FORCE IN MEMBER CD OF THE LOADED TRUSS SHOWN IN Fig 1.4 4000lb C -6000lb 6' G 3' 3' 3' 3"- -4000lb -3000lb -5000lb