Your standard curve will contain the log of concentration in ng/mL on the x axis, and absorbance on the y axis. Suppose you get an absorbance value for an unknown sample and find an x value of 2 using your standard curve. What is the concentration in ng/mL that the absorbance value corresponds to? O 200 02 O e^2 O 100

Your standard curve will contain the log of concentration in ng/mL on the x axis, and absorbance on the y axis. Suppose you get an absorbance value for an unknown sample and find an x value of 2 using your standard curve. What is the concentration in ng/mL that the absorbance value corresponds to? O 200 02 O e^2 O 100

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

The following Absorbance vs concentration of nitrite graph is obtained for a set of data: Absorbance Vs Concentration y = 1.6628x+0.0373 R? = 0.9893 1.8 1.6 1.4 1.2 1 0.8 0.6 0.4 0.2 0.2 0.4 0.6 0.8 1 Concentration of nitrite (mg/L) Determine the concentration of unknown solution for which the absorbance is determined as 0.69 A. More data is required В. 0.69 С. 0.65 D. 0.39 Absorbance
P 1. Absorbance Given the following standard curve of Absorbance vs Concentration (mM), what in the concentration of Aspirin if the absorbance is O.822? 1.2 y = 0.0032x+0.1043 R2 0.9975 0.8 0.6 0.4 0.2 250 000 350 Concentration MacBook Air 08 ODO F4 110 F8 F5 DD 93 63 6. R.
For the data below, Write the linear equation of the line (use 5 Decimal places and don't add "space") example y=1.23456x+4.32101 Cu mg/L Absorbance 0 0.002 0.045 0.093 0.133 0.177 0.197 24 4 6 8 10
A colored solution of concentration 0.0344 mol/L has an absorbance of 0.481. What is the concentration a solution of the same solute with an absorbance of 0.651? Assume that the same sample celf is used for both readings. Report your answer to 3 significant figures.
Series 9. Mixtures Brass Sand + CuSO4• 5H2O White wine Series 9. Mixtures (continued) Water and BaSO4 Oil and water Vinegar
The total hardness is due to one or a combination of Ca2+, Mg2+, and Fe2+ in your sample. It is convenient to express this hardness as though it was entirely due to Ca2+. Making this assumption, determine the number of moles of Ca2+ present in the bottled water sample titrated. (enter your answer with 3 significant figures) 25.00 ml water sample, 19.040 ml of 4.965x 10−3 M EDTA solution to reach the endpoint.
Exactly 1.00 grams of granular table salt was dissolved in deionized water up to 500 mL. An aliquot of 20 mL was titrated with AgNO3 (T = 8244 mg/mL) and consumed 46.60 mL to reach end point. If the impurities are just water, calculate the percent Moisture. Ans in 1 sig figure.
You begin preparation of the calibration curve to measure absorbance vs concentration of FeSCN²+. To do so, you add 4.244 mL of 0.200 M Fe(NO3)3 to a cuvette and then directly add 413 μL of 0.001 M KSCN. What is the resulting concentration of FeSCN²+, assuming complete conversion of SCN to FeSCN²+? Enter your answer in units of mM to four digits after the decimal.
You want to determine the concentration of NaCl in a water. In preliminary analysis, it appears to be saline water with a NaCl content of approximately 4%. Should you dilute the sample if your titrant has a concentration of 0.1 M and you want to spend 25 mL of sample? Solution: You must dilute approximately ten times, taking 10 mL of sample and making up to 100 mL. In this way, 17.20 mL of titrant will be spent.
Complete the table by entering the molarity of B2- for each standard solution. Show an illustrative calculation for tube ‘A’. Use the dilution formula and express each result to one more digit than allowed by applying the rules of significant figures. Standard Volume of stock B2- solution taken, mL Molarity of dilute B2 Construct a graph of Absorbance vs. molarity of B2- in Excel using the data in the preceding table. Make certain to title the graph and include axes labels with proper units. Absorbance is dimensionless (has no unit). Add a linear trendline to the graph but do not set the y-intercept to zero Solid M2B is added to 25 mL of water, the resulting mixture is continually stirred for 1 hour. At this point, it is assumed that equilibrium (eqn 3) has been established. The mixture is transferred to a test tube, and the test tube is centrifuged to assure that any residual solid M2B is fully settled out. A portion of the supernatant in the test tube is carefully…
Write your complete solutions on yellow paper, round your answers to the appropriate number of significant figures, and box the final answer. The deadline for submission is at the end of the class. Note: You do not need to write your solutions for the items that can be derived from your calculators. 1. Three students (Saerom, Hayoung, and Jiwon) are asked to determine the ppm Ca in a drinking water sample by titration with EDTA. Each student performed five trials for the sample. The results in ppm Ca are the following: Saerom Hayoung Jiwon a. Get the mean, SD, and % RSD of each student's results. b. If the true value is 35 ppm, calculate the relative error of each student's results. c. Comment on the precision and accuracy of each student's results. The maximum % RSD and the relative error set by the lab is 5.0%. d. Use the following table to summarize your answers. Mean SD %RSD Relative Error Comment 31, 32, 33, 33, 32 35, 34, 34, 35, 34 35, 38, 33, 35, 37 Saerom Mean SD 95% CI…
Hd 10 5 0 5 mL of NaOH added 10 20 15 10 LO 5 0