With vs = 12V, a. calculate the voltages v4 and v5 in Figure 1. b. calculate the currents going through R and R5 (IŔ and IÃ§) in Figure 1. c. calculate the dissipated power in R4 and R₁ (PR₁ and PR) in Figure 1. Table A: Figure 1 circuit values IR₂ (mA) IRS (MA) V4 (V) V5 (V) PRA (MW) PR5 (MW)

With vs = 12V, a. calculate the voltages v4 and v5 in Figure 1. b. calculate the currents going through R and R5 (IŔ and IÃ§) in Figure 1. c. calculate the dissipated power in R4 and R₁ (PR₁ and PR) in Figure 1. Table A: Figure 1 circuit values IR₂ (mA) IRS (MA) V4 (V) V5 (V) PRA (MW) PR5 (MW)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.8MCQ: An ac resistance is higher than a dc resistance. True False

See similar textbooks

Similar questions

Determine the DC currents (IB, Ic and lĘ) and dc junction voltages (VBE, VCE and VCB) Ig=Blank 1 mA, Ic=Blank 2 mA, IĘ=Blank 3 mA, VBE= Blank 4 V, VCE = Blank 5 V and VCB = Blank 6 V Use 2 decimal places. Use the following values: VBB = 2V RB = 7 kQ Rc = 248 Q Vcc = 19 V BDc = 56 Blank 1 Add your answer Blank 2 Add your answer Blank 3 Add your answer Blank 4 Add your answer Blank 5 Add your answer Blank 6 Add your answer
8. Liquids with solid impurities a) Have higher dielectrie strength b) Of large size have higher dielectric strength c) Have lower dielectric strength as compared to pure liquids d) None of the above 9. Peak to peak ripple is defined as a) the difference between average de voltage and peak value b) the difference between maximum and minimum de voltage c) the difference between maximum ac and average dc voltages d) the difference between ac (rms) and average de voltages 10. In a Cockroft-Walton circuit, input voltage 100 kV load current 25 mA, supply frequency 100 Hz, each capacitor 10 nF. The optimum no. of stages for maximum output voltage is a) 1 b) 2 c) 10 d) 35
multirange ammeter was designed using direct method to give three scales with Rsh1= 0.001285989 0, Rsh2=0.000562552 0, and Rsh3=0.000100001 Q. The d'Arsonval meter has Rm=6 Q and full scale current of 1.5 mA. Find the ranges.? 8 (Ctrl) -
A voltage-multiplier has a Vm = 60 V peak sinusoidal secondary voltage. During the positive half-cycle, D1 conducts and D2 is cut-off, charging C1 up to what voltage level? C1 HE (A) OV B) 60 V V Ⓒ120 V (D) 180 V Vp 1:1 Vm = 60 V D1 D2 не C2 Ideal diodes C3 HE D3 D4 C4 :
aloulated m O1 the value you Up = A cos wt +1o Calaulate maarli)-min(i) =? Use constant voltage drop mad. Don7 to write units. . - 3.7V forget
a) What is the peak voltage across R2? b) What is the RMS value of I1?
Q2) Consider the circuit in Figure (3), and answer 3 branch only. a) What type of circuit is this? b) What is the total peak secondary voltage? c) Find the peak voltage across each half of the secondary. d) Sketch the voltage waveform across RL. 4:1 120 V rms RL 1.0 k2 D2 eelee
In the figure on the right, the ideal batteries have emfs &1= 10 V and 82 = 83 = 6 V and the resistors are identical with R = 5 ohm. (a) independent eqaations to solve three unknown currents i, iz, and i; as shown in the figure and solve for the current i. That is, what is the magnitude and direction of iz? (b) (c) (d) batteries are equal to the total power loss in all the resistors. RI i ww. Apply Kirchhoffs loop and junction rules and obtain three El R3 R, 83 What is the magnitude and direction of iz? What is the total energy dissipation rate in all the resistors Prove that total power supplied to the circuit by the ww wwH
iv) Determine the peak-to-peak ripple voltage, Vrípp), of the circuit in Figure 3. v) Determine the output DC voltage level of the circuit in Figure 3. vi) Determine the ripple factor of the circuit in Figure 3. D (Si) D (Si) Vun = 9 V 5 Hz pp Rļoad = 5 ΚΩ Vout D (Si) D (Si) 200UF +
Discuss the difference between Alternating Current (AC) and Direct Current (DC)
Determine the loop currents Ia, I,, and Ic. 100 Ic 100 100 100 100 Ib 55V 100 V la
The Value of R1 is 39.4Ohms. explain