With the use of an engineer's level, the reading from a rod was recorded as 2.50m when the rod was 100m away. When the bubble was leveled through 5 spaces on the tube, the new reading was recorded at 2.58m. If the bubble was leveled to the left by 6 spaces, determine the new rod reading. 2.404 m 2.452 m 2.51 m 2.517 m

With the use of an engineer's level, the reading from a rod was recorded as 2.50m when the rod was 100m away. When the bubble was leveled through 5 spaces on the tube, the new reading was recorded at 2.58m. If the bubble was leveled to the left by 6 spaces, determine the new rod reading. 2.404 m 2.452 m 2.51 m 2.517 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Select one: a. 0.79 m b. 1.20 m c. 0.90 m d. 0.60 m
The following level notes for the determination of BM#2 do not check. The elevation of BM#1 and the rod readings are correct. Determine the corrected elevation of BM#2. STA B.S. H.I. F.S. ELEV. BM 1 6.72 127.36 120.64 TP 1 12.43 138.55 1.24 126.12 ТР 2 2.65 140.09 1.11 137.44 TP 3 0.54 132.59 8.04 132.05 ТР 4 4.27 124.55 12.31 120.28 BM 2 3.02 121.33
DIFFERENTIAL LEVELING Problem: Complete the differential level notes shown in the table below. STA BS HI FS ELEV BM1 2.085 137.450 m TP, 2.015 0.982 TP2 1.864 1.428 TP3 0.579 1.527 BM2 0.423 2.423 TP4 1.446 1.807 TP5 1.778 1.725 TP6 2.051 2.339 TP, 2.920 1.005 BM3 3.186 2.358 TP3 2.805 0.995 TPg 0.774 1.206 BM4 0.603
Q2/ Complete the settlement table below and verify the correctness of the calculations. Then check the correctness of the work, bearing in mind that the length of the leveling line is 2,250 meters, bearing in mind that the required level of leveling is the third. Find the closing error and adjust the levels if necessary, suppose that the error equal for all points. Elevation Station B.M1 TP1 TP2 TP3 TP4 TP5 TP6 BM1 B.S 1.23 0.955 1.332 1.652 2.558 2.465 2.882 H.I F.S 1.735 2,642 3.000 2.524 2.221 0.755 0.218 50,000
2. A 1" reading theodolite having a multiplying constant of 100 and an additive constant of 0 was centered and levelled a height of 1.48 m above a point C of reduced level 46.87 m. A levelling staff was held vertically at points D and L in turn and the readings shown in table 1 were taken. Calculate (i) the reduced levels of points D and L (ii) the horizontal length of DL. Staff position Staff reading (m) Vertical circle Horizontal circle D L 3.240, 3.047, 2.853 2.458, 2.230, 2.002 readings 87°38'53" 92°21'36" readings 56°49'31" 98°07'18"
In the two-peg test of a dumpy level, the following observations were taken. Rod reading at A Rod reading at B (m) (m) Instrument at pt. M 0.396 0.910 Instrument at pt. P 1.4 2.14 Point M is equidistant from both A and B, while point P is outside line AB, 2.5 meters from A and 79.27 m from B. *in the space provided, indicate: a. Find the difference in elevation between A and B. b. Adjust the correct readings when the instrument was at point P.
The accompanying schematic arrangement of line portray a differential level route. Th values indicated represent back-sight and foresight readings taken at different points as labelled. Prepare the complete differential level notes for the information shown and the customary arithmetic check. STA. BS HI FS ELEV. BM1 2.35 356.65 TP1 1.37 3.28 TP2 3.08 2.04 ТРЗ 1.54 3.61 ТР4 0.85 3.69 BM2 3.07 Arithmetic Check: Elevation BM1+(SUMMATION OF BS) -(SUMMATION OF FS) =BM2 A. Height of the instrument at TP4. B. Elevation of TP4. C. Difference in elevation of TP1 and TP4.
A 3 meter long subtense bar was first set up at A and subsequently at B, and the subtended angle to the bar, as read from a theodolite position somewhere along the middle of the line AB, were recorded as 3deg 5’00” and 2deg 6’00". Determine the length of line AB. a. 125.69 m b. 137.58 m c. 256.12 m d. 165.69 m
An instrument was setup at A and the angle of depression to a vane 2 m above the foot of the staff held at B was 5°. The horizontal distance between A & B was known to be 3000 metres. Determine the reduced level of the staff station B if the staff reading on benchmark located at 3000 m is 2.865 metres. Take RL of benchmark = 350.205 metres. 2m B 3000m A 2.865m BM RL = 350.205m
The following data were taken from the peg method of adjustment. Instrument at 1 Instrument at 2 Rod rdg. on A Rod rdg. on B 0.296 m 1.563 m 0.91 m 2.14 m Point 1 is midway between A and B. Point 2 is 2.5 m to the left of A, 79.27 m from B. 1. Determine the magnitude of the true difference in elevation between A and B. 2. Determine the correct rod reading at A for horizontal sight if the instrument is set up at point 2.
The table below is the page of a level field book. Calculate the reduced levels of points C, F and H if the height of instrument (H.I) for the first and second position of the level= 33.1 and 33.5 respectively. Note: the readings inside the brackets (.....) represent inverted .staff reading St. No. A B с le D E F G H I BS (3.4) ? IS (2.7) 0.9 (1.56) (1.9) 2.6 (0.8) FS 0.7 (2.9) C-35.8, F-32.4, H=36.4 C-36.8, F=32.4, H=36.4 C-34.6, F=30.9, H=36.4 C=36.5, F=34.6, H=36.4 C-32.2, F-35.4, H=34.3
solve a and b given asap. a) In a two-peg test of a dumpy level, the following readings were taken: Instrument at R, mid-way Staff readings between pegs P and Q: at P 1.525 m at Q 1.230 m Instrument near P: at P 1.420 m at Q 1.025 m How much is the line of collimation inclined upwards or downwards? What should be the correct staff reading at Q with the instrument near P to keep the line of collimation truly horizontal? b) Two pegs A and B are driven 100.0 m apart. In the adjustment of a dumpy level, following observations were recorded: observations given in the image. State whether the instrument is in adjustment. Find the R.L. of B.