Which of the following statements is not true about the linear polarization technique? a) Measurements begin at-20 mV from OCP and end around +100 mV from OCP b) The slope of the plot is AE/AC is given in volts/amperes or mV/mA c) This technique can be used to determine very low rate of corrosion d) It can be used to monitor corrosion rate in process plant

Which of the following statements is not true about the linear polarization technique? a) Measurements begin at-20 mV from OCP and end around +100 mV from OCP b) The slope of the plot is AE/AC is given in volts/amperes or mV/mA c) This technique can be used to determine very low rate of corrosion d) It can be used to monitor corrosion rate in process plant

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter1: Atomic Structure

Section: Chapter Questions

Problem 6RQ: How many valence electrons are generally contained in materials used for insulators?

See similar textbooks

Similar questions

What is CEMF?
For the diodes used , at what Voltage (VD) does condection stars .
1. Answer the following with "TRUE" or "FALSE" then explain why. ________a.) Charges choose the path of least resistance. Given a resistor in parallel with a diode, no current willflow through the resistor when the applied voltage exceeds the diode’s forward voltage.________b.) Since diodes are unidirectional components, it will always block AC signals e.g. pulse train,sawtooth, triangular signals.________c.) Silicon diodes typically have a forward voltage of 0.7V.
At 305 °K temperature, the voltage equivalent of temperature of diode is ______________________V. Assume the Boltzmann's constant is 8.62*10-5 eV / K Answer:
Using second approximation for a diode to calculate the load voltage.
T11. Fermi energy level for p-type extrinsic semiconductors lies (a) At middle of the band gap (b) Close to conduction band (c) Close to valence band (d) None
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
5. A voltage source produces a "Triangle" wave and is connected to a series diode and resistor circuit as shown. D1 KH D V1 #1 V R1 R Using the nominal piecewise linear model for a diode, determine from the following possibilities the graph that best represents the voltage across the resistor? (Delete those that do not apply) (Blue curve VR, dashed curve V1). Then determine which graph best represents the voltage across the diode.
What is going to happen for the depletion region if the P-type material has more doping in the PN-junction?
The density of doping of zener diode is less than normal diode. True False
In half wave rectifier with filter, if the capacitance is increased, the ripple factor increases. True or false
The datasheet shown below for a group of commercial Zener diodes, according to the datasheet the typical voltage and leakage current of the Zener diode with model number 1N4732A are: * Tolerance- S% FAIRCHILD SEMICONDUCTOR Datasheet 1N4728A - 1N4758A Zener Diodes D0041 Glass case Electrical Characteristics 1,-25°C untess otherwise noted Vz (V) @ Iz (Note 1) Max. Zener Impedance Leakage Current Test Current Device Zz@lz ZzK @ IZK (mA) IR (HA) VR (V) Min. Тур. Мах. Iz (mA) (오) Izk (2) 3.315 3.42 1N4728A 3.3 3.465 76 10 400 1 100 1 1N4729A 3.6 3,78 69 10 400 100 1N4730A 3.705 4.085 3.9 4.095 64 9 400 50 1N4731A 4.3 4.515 58 400 10 1N4732A 4.465 4.7 4.935 53 500 1 10 1 1N4733A 4.845 5.1 5.355 49 550 10 1 1N4734A 5.32 5.6 5.88 45 600 10 1N4735A 5.89 6.2 6.51 41 2 700 1 10 3 1N4736A 6,46 6.8 7.14 37 3.5 700 1 10 1N4737A 7.125 7.5 7.875 34 4 700 0.5 10 b. 1V and 10uA O c. 4.7V and 10uA a. 4.465V and 10UA O d. 4.7V and 53mA