Which of the following statements are correct in the context of thermal conductivity? (Check all that apply.) Check All That Apply The thermal conductivity of gases is proportional to the square root of absolute temperature. The thermal conductivity of liquids is proportional to the square root of absolute temperature. The thermal conductivity of most liquids decreases with increasing temperature. The thermal conductivity of most liquids increases with increasing temperature.

Which of the following statements are correct in the context of thermal conductivity? (Check all that apply.) Check All That Apply The thermal conductivity of gases is proportional to the square root of absolute temperature. The thermal conductivity of liquids is proportional to the square root of absolute temperature. The thermal conductivity of most liquids decreases with increasing temperature. The thermal conductivity of most liquids increases with increasing temperature.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.70P: The thermal conductivity of fibreglass insulation at 67F is 0.02 Btu/h ft F. What is its value in SI...

See similar textbooks

Similar questions

An electric heater producing 260 W of heat is used to warm up a room containing 7 m3 of air. If we assume the room is perfectly sealed and there is no heat loss through the room boundaries, such that all of the heater output goes into increasing the air temperature, how long will it take to heat up the air in the room from 5.0 °C to 24.1 °C? Give your answer to the nearest minute and assume that the specific volume (v = 0.85 m3/kg) and specific heat capacity at constant volume (cv = 1.005 kJ/(kg K)) remain constant throughout the heating process.
The rate of heat lost through insulation varies inversely as the thickness of the insulation. The rate of heat lost through a 3.5-inch thickness of insulation is 2200 Btu per hour. What is the rate of heat lost through a 5-inch thickness of the same insulation?
3. Thermal conductivity of a substance is measured as k = k, TIT, . Find an average value for thermal conductivity in the temperature range of T1 and T2. [Ans. = (k, /272 xT} 2 – T}/2) (T2 – T;) 1|
One wall of a room measures 14 feet long and 8 feet high. It's contains a window 5 feet wide and 3.5 feet high. The wall has an R-Value of 15.5. the unit R-value of the window is 3.5. Find the rate of heat flow through the wall when the inside air temperature is 68 degrees Fahrenheit and the outside temperature is 5 degrees Fahrenheit.
The left side of this equation tells how much energy Q the cylinder gives to the water while it cools. The right side of this equation tells how much energy Q the water and aluminum cup absorb from the cylinder to warm up. Because it is the same energy, they are equal. What is known in this equation? Mcyl 411.7 g, malum 46.5 g, malum+water = 175 g Can you find: mwater =? g Twater = Talum = 20°C (water and cup of room temperature) 90°C, T; = 35°C (hot cylinder and cool "cylinder+cup+water" temperatures) Tcyl kCal Calum = 0.22, Cwater 1 (specific heat of water and aluminum, measured in units kg-°C What are we looking for is Ccul - How we find it? Plug all the numbers into the equation (1), Ccul will be one unknown which you can calculate from the equation. Important, convert all the masses from grams to kilograms! After you find Ccyl, compare it to known value for the copper 0.093(our cylinder is made out of copper). |Ceyl -0.093| % : · 100% 0.093
Give True or False for the following: 1.In liquids and gases, heat transmission is caused by conduction and convection 2.The surface geometry is the important factor in convection heat transfer 3. The heat transfer by conduction from heated surface to the adjacent layer of fluid, 4. The heat transfer is increased in the fin when &> 1 5.The unit of the thermal diffusivity is m²/s 6. Temperature change between the materials interfaces is attributed to the thermal contact resistance 7. A material that has a low heat capacity will have a large thermal diffusivity. 8. Heat conduction flowing from one side to other depends directly on thickness 9.Fin efficiency is the ratio of the fin heat dissipation with that of no fin 10.The critical radius is represented the ratio of the convicted heat transfer to the thermal conductivity
The figure below shows the energy balance for a planet with an atmosphere. The atmosphere is fully transparent to solar radiation and fully absorbing of infra-red radiation. Fill in values for the arrows in the figure assuming Ein=100 W/m?. Doing arrows in the order labeled should help. Enter the values for 1-4 in the text box. What is the temperature of this planet (use E = 2 = oTª , o = = 5.67 x 10-8 W )? m K4 5. K 6. °C 7. °F Sun 2. 1. 3. 4.
Calculate, in degrees Rankine, the temperature interval of 73.6°C. Use two decimal places in your answer
A solid steel cube is stored in a freezer, where the temperature is −20.0 ̊C. While the cube is in the freezer, you measure its side length (L) to be 1.75050 meters. The cube is then placed outside for a long time, so that the temperature of the cube reaches the temperature of the air outside. As a result, the side length increases to 1.75170 meters due to thermal expansion. The coefficient of linear expansion for steel is 12.0×10−6 ̊C−1. (a) What is the temperature of the air outside? Give your answer in degrees Celsius ( ̊C). (b) What is the volume of the cube when its temperature is 20.0 ̊C? Give your answer in cubic meters (m3).
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
Heat transfer can be defined as the transmission of energy from one region to another due to temperature difference. Select one: O a. False O b. True
Heat transfer deals with the amount of heat while in Thermodynamics, we try to find the rate of energy transfer. Not sufficient information False True