Which of the following best describes the temperature coefficient of resistance of a certain material? O It can be used to predict the temperature of a certain material given its specific resistance. It measures the final electrical resistance of a material per degree of temperature change. It measures changes in the electrical resistance of a material per degree of temperature change. O It measures changes in the electrical resistance based on the initial temperature of the material.

Which of the following best describes the temperature coefficient of resistance of a certain material? O It can be used to predict the temperature of a certain material given its specific resistance. It measures the final electrical resistance of a material per degree of temperature change. It measures changes in the electrical resistance of a material per degree of temperature change. O It measures changes in the electrical resistance based on the initial temperature of the material.

Physics for Scientists and Engineers with Modern Physics

10th Edition

ISBN:9781337553292

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter27: Direct-current Circuits

Section: Chapter Questions

Problem 1P: Two 1.50-V batterieswith their positive terminals in the same directionare inserted in series into a...

See similar textbooks

Similar questions

A student uses a 100.00-W, 115.00-V radiant heater to heat the student’s dorm room, dining the hours between sunset and sunrise, 6:00 p.m. to 7:00 a m. (a) What current does the heater operate at? (b) How many electrons move through the heater? (c) What is the resistance of the heater? (d) How much heat was added to the dorm room?
A 10.00-meter long wire cable that is made of copper has a resistance of 0.051 ohms, (a) What is the weight if the wire was made of copper? (b) What is the weight of a 10.00-meter-long wire of the same gauge made of aluminum? (c)What is the resistance of the aluminum wire? The density of copper is 8960 kg/m3 and the density of aluminum is 2760 kg/m3.
A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg • °C, assuming no heat escapes?
Review When a metal rod is heated, its resistance changes both because of a change in resistivity and because of a change in the length of the rod. If a silver rod has a resistance of 2.00 at 22.0C, what is its resistance when it is heated to 200.0C? The temperature coefficient for silver is = 6.1 103 C1, and its coefficient of linear expansion is 18 106 C1. Assume that the rod expands in all three dimensions.
(a) Digital medical thermometers determine temperature by measuring the resistance of a semiconductor device called a thermistor (which has a= - 0.0600/°C ) when it is at the same temperature as the patient. What is a patient's temperature if the thermistor’s resistance at that temperature is 82.0% of its value at 37.0°C (normal body temperature)? (b) The negative value for a may not be maintained for very low temperatures. Discuss why and whether this is the case here. (Hint: Resistance can’t become negative.)
(a) During surgery, a current as small as 20.0A applied directly to the heart may cause ventricular fibrillation. If the resistance of the exposed heart is 300 what is the smallest voltage that poses thisdanger? (b) Does your answer imply that special electrical safetyprecautions are needed?
A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any wires used for connections is negligible, (a) What is the current through the resistor? (b) What is the power dissipated by the resistor? (c) What is the power input from the battery; assuming all the electrical power is dissipated by the resistor? (d) What happens to the energy dissipated by the resistor?
(a) A defibrillator sends a 6.00-A current through the chest of a patient by applying a 10,000-V potential as in the figure below. What is the resistance of the path? (b) The defibrillator paddles make contact with the patient through a conducting gel that greatly reduces the path resistance. Discuss the difficulties that would ensue if a larger voltage were used to produce the same current through the patient, but with the path having perhaps 50 times the resistance. (Hint: The current must be about the same, so a higher voltage would imply greater power. Use this equation for power: P=I2 RP = .)
A battery has an emf of 15.0 V. The terminal voltage of the battery is 11.6 V when it is delivering 20.0 W of power to an external load resistor R. (a) What is the value of R? (b) What is the internal resistance of the battery?
An aluminum wire 1.628 mm in diameter (14-gauge) carries a current of 3.00 amps, (a) What is the absolute value of the charge density in the wire? (b) What is the drift velocity of the electrons? (c) What would be the drift velocity if the same gauge copper were used instead of aluminum? The density of copper is 8.96 g/cm3 and thedensity of aluminum is 2.70 g/cm3. The molar mass ofaluminum is 26.98 g/mol and the molar mass of copper is 63.5 g/mol. Assume each atom of metal contributes one free electron.
2.The figure below shows cross sections through three long conductors of the same length and material, with circular cross-sections of edge as shown. Conductor B(outer radius 2R) will fit snugly within conductor A(outer radius 3R, and conductor C (radius R) will fit snugly within conductor B. Rank the three conductors according to their end-to-end resistance. A B с O
Consider two copper wires. One has three times the cross-sectional area of the other. How do the resistances of these two wires compare? O The thicker wire has twice the resistance of the shorter wire. Both wires have the same resistance. O The thicker wire has half the resistance of the shorter wire. O none of the given answers hp N P. 88