Which among these is used to determine or compute for the Transmission Line AC Resistance? A. Conductor Real Power Loss divided by the square root of the Conductor Current flowing. B. Conductor Resistivity multiplied to the Length of the Conductor divided by the Cross-Sectional Area of the Conductor. C. Conductor Conductivity multiplied to the Length of the Conductor divided by the Cross-Sectional Area of the Conductor. D. Conductor Real Power Loss divided by the square of the Conductor Current flowing

Which among these is used to determine or compute for the Transmission Line AC Resistance? A. Conductor Real Power Loss divided by the square root of the Conductor Current flowing. B. Conductor Resistivity multiplied to the Length of the Conductor divided by the Cross-Sectional Area of the Conductor. C. Conductor Conductivity multiplied to the Length of the Conductor divided by the Cross-Sectional Area of the Conductor. D. Conductor Real Power Loss divided by the square of the Conductor Current flowing

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.1P: The Aluminum Electrical Conductor Handbook lists a dc resistance of 0.01558 ohm per 1000 ft at 20C...

See similar textbooks

Similar questions

Discuss the various conductor materials used for overhead lines. What are their relative advantages and disadvantages?
A three phase, 11 KV, underground cable system, consider a single core of conductor radius 0.5 cm diameter and lead sheath of 1.25 cm. The core and lead sheath have been separated by two intersheaths with radius 0.75 cm and 1 cm. Draw the cable core, dielectric and intersheath layers showing the thickness of each layer, then determine the voltages on the both intersheaths. Suppose the maximum stress on the layers are the same.
Q4(a) The differences between TWO unequal towers 60 m support a transmission line conductor at road crossing. The given span length is 499.5 m as show in Figure Q4(a). If the tension in the conductor is 1700 kg, determine the minimum clearance of the conductor and road and clearance mid-way between the supports. Weight of conductor is 1-5 kg/m. Bases of the towers can be considered to be at road level. Given height of the tower A is 35 m from the ground level. Span Length= 499.5 ROAD Figure Q4(a)
Q2. What is the benefit of using stranded conductors in transmission systems?
A three phase, 33 KV, underground cable system, consider a single core of conductor radius 0.8 cm diameter and lead sheath of 2.3 cm. The core and lead sheath have been separated by two intersheaths with radius 1.3 cm and 1.8 cm. Draw the cable core, dielectric and intersheath layers showing the thickness of each layer, then determine the voltages on the both intersheaths. Suppose the maximum stress on the layers are the same. Please i need it know please
An overhead line has span of 260m. The tension in the line is 1200kg while the conductor weighs 650 kg per 100 meters. Calculate the maximum SAG in the conductor. If the height of the tower is 13 meters, estimate the clearance of conductor to the ground. Draw a figure and mark values of sag, clearance, span, height of conductor etc.
a) Explain the demerits of non-uniform potential gradient of insulated cable. b) 'Insulation resistance varies proportionally with the value of insulation thickness - justify this statement with appropriate equations. c) A single core cable to be used on a 50kV single phase system. Maximum permissible dielectric is not to exceed 35kV/cm (peak). I. Determine the most economic conductor and cable diameter. II. Estimate voltages on the inter sheaths, if two inter sheaths are introduced to increase 32% of the existing working voltage of the cable using the method of 'inter sheath grading
Theoretically solve an unknown resistance for Transmission line conductor by using any two methods (for example: Wheatstone bridge, Kelvin bridge, Potentiometer method etc). And then compare them and state that between in this two used methods which one is better and why. [Note: You can choose any practical value for ratio arms]
The cost of a single phase overhead feeder is OMR 7 a per km ( a is area of cross section in sq mm) and the interest and depreciation charges on feeder are 10%. Determine the most economical current density to use for distribution requiring full load current of 75% of the year. The cost of generating electrical energy is 12 baisa per unit. Assume resistance of 1 m length and 1 mm2 section of conductor as 1/62 ohm. Current density A/mm2
What are the colors of the conductors in nonmetallic-sheathed cable for a. 2-wire cable? _______________, _______________ b. 3-wire cable? _______________, _______________, _______________
A stranded conductor is an example of a composite conductor. True False
Subject: Electrical & Electronics Engineering Course: Power Systems Question: What is GMR and GMD? Explain your answer in case of a composite conductor.