Where it get the value 2 and 10 for the green circle? Please expl A rectangular beam with b = 270 mm, d = 500 mm is provided with 10mm vertical stirrups with fy = 276 MPa. Assuming fc' = 21 MPa;a) Determine the required spacing if V₁ = 35 kNb) Determine the required spacing if V₁ = 92 kNc) Determine the required spacing if V₁ = 236 kNd) Determine the required spacing if V₁ = 473 kNSolutionShear carried by concreteV = 0.17 A√√fe'b dV = 0.17 (1) √√21(270)(500) = 105,170 NOVС20.75(105170)2= 39,439 N a) V₁ = 35000 N <-b)V₁ =92000 NUVV₁ = " -V₁V. =SA,=920000.7527 (10)²4QV c2A, f,dS =V.SStirrups not necessary- 105170 = 17496.67 N=157.1mm²157.1( 276 )50017496.67= 1239 .08 mm

This question is related to the Design concrete structures.In this question ask about the , Where it…

Answered: Where it get the value 2 and 10 for the…

Engineering

Civil Engineering

Where it get the value 2 and 10 for the green circle? Please expl

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. use concrete strength f's=21MPa and steel yield strength fy=415MPa for 20mm bars and fy=275MPa for 16mm bars. determine the depth of the uniform rectangular stress block on the beam section at ultimate stage when subject to positive bending.
A rectangular beam has b = 300 mm and d =490 mm. Concrete compressive strength f′c = 27.6MPa and steel yield strength fy = 276 MPa. Calculate the required tension steel area (in mm2) if the factored moment Mu = 485 kN-m. Calculate the required tension steel area (in mm2) if the factored moment Mu = 600 kN-m.
A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It has a reinforcement area of 4072 sq. mm at the bottom. fc' = 25 MPa, fy = 414 MPa. a) Determine the depth of compression block, "a".
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 27 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the maximum steel ratio if the beam is singly reinforced in positive bending with the given material strengths and the tensile strain is limited to 0.005 upon crushing of concrete. Write the answer in 5 decimal places only.
A rectangular beam 300 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the maximum steel area for a tension controlled singly reinforced condition in positive bending
A 90mm concrete slab is supported by a beam 7.50m clear span and 1.20m on center. Web dimension and effective depth are 300mm and 500mm respectively. If the factored moment is 730kN-m, fy=420MPa and fc’= 21MPa. Use a reduction factor of 0.90. a. Determine the maximum steel area in mm2. b. What is the balanced steel area in mm2? c. Determine the design strength, kN-m.
The beam has a 20 Mpa concrete, dimensions of b=400mm, d=550 mm and reinforced with 4-25 mm diamter rebars. If it sustains a bending moment of 100 KN-m. Determine if the beam is safe using the "transformed section method". n=10
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 27 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the design moment capacity in kN∙m of the beam in negative bending. Write the answer in 2 decimal places only.
A 400 mm diameter column will carry 1300 kN load. Use fy=345MPa and fc=21 MPa. a.)Determine the required area of reinforcement.b.)Determine the spiral steel ratio of the column c.)Determina the spacing of spirals
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with a 4-20mm diamter bars and at the top with 2-16 mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f'c = 32.09 MPa and steel yield strength fy=345 MPa for 20mm bars and fy=275 MPa for 16mm bars. Determine the maximum steel area for a tension-conctrolled singly reinforced condition in positive bending with the given material strength.
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 1. Determine the maximum steel ratio if the beam is singly reinforced in negative bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in 5 decimal places only. 2. Determine the maximum steel ratio if the beam is singly reinforced in positive bending with the given material strengths and the tensile strain is limited to 0.005 upon crushing of concrete. Write the answer in 5 decimal places only.
Determine the theoretical steel area’s required for the tension of a rectangular section with b = 350 mm, d = 700 mm under a factored moment of 1,500 kN-m. If compression steel is required, assume it will be placed 70 mm from the compression fiber of concrete. Use fc’ = 28 MPa and fy = 420 MPa.