When the excitation of an unloaded salient pole synchronous motor suddenly gets disconnected, thenthe motor stopit runs at lower speedA SCRIM is considered as induction motor that operate inAC or DC Supplyc. it runs at the same speedd. it runs at very high speeda.b.c. DC Supplyа.AC SupplyAn over-excited synchronous motor takeleading currentb.b.d. None of thesec. lagging currentd. none of thesea.Inphase the current with the voltageA three-phase phase induction motor is rated 5 hp, 75 % power factor at 220 volts. What is its full load current?а.22.5 Aс. 16.9 Аb.13.06 Ad. 18.5 A

Synchronous motor: This is a motor that converts the electrical input into mechanical output. Due to…

When the excitation of an unloaded salient pole synchronous motor suddenly gets disconnected, then the motor stop it runs at lower speed A SCRIM is considered as induction motor that operate in AC or DC Supply AC Supply An over-excited synchronous motor take leading current b. Inphase the current with the voltage A three-phase phase induction motor is rated 5 hp, 75 % power factor at 220 volts. What is its full load current? c. it runs at the same speed d. it runs at very high speed а. b. c. DC Supply a. b. d. None of these c. lagging current d. none of these а. а. 22.5 A c. 16.9 A b. 13.06 A d. 18.5 A

When the excitation of an unloaded salient pole synchronous motor suddenly gets disconnected, then the motor stop it runs at lower speed A SCRIM is considered as induction motor that operate in AC or DC Supply AC Supply An over-excited synchronous motor take leading current b. Inphase the current with the voltage A three-phase phase induction motor is rated 5 hp, 75 % power factor at 220 volts. What is its full load current? c. it runs at the same speed d. it runs at very high speed а. b. c. DC Supply a. b. d. None of these c. lagging current d. none of these а. а. 22.5 A c. 16.9 A b. 13.06 A d. 18.5 A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The rotor resistance and standstill reactance of a 3-phase induction motor are 0.015 Q and reactance 0.09 0 per phase. (i) What is the p.f. of the motor at start? (ii) What is the p.f. at a slip of 4 per cent? (iii) If the number of poles is 4, the supply frequency is 50-Hz and the standstill e.m.f. per rotor phase is 110 V, find out the full-load torque. Take the full-load slip as 4 per cent.
L-1). The 3-phase wound-rotor induction motor has .... . a) high starting torque b) low starting current c) both "a" and "b" d) neither "a" nor "b" L-2). The 3-phase wound-rotor induction.........a) motor has a wire wound rotor b) motor's rotor can be connected to an external resistive load by way of slip rings and brushes c) motor requires more maintenance than the 3-phase squirrel-cage induction motor d) all of the above L-3). The 3-phase wound-rotor induction motor's rotor circuit's resistance should be adjusted so it is__________ during starting. a) low b) high c) either "a" or "b" d) neither "a" nor "b" L-4). Will a 3-phase wound-rotor induction motor start with no external circuit connected to its rotor leads? a) yes b) no
An 8 pole, 50 Hz slip ring induction motor runs at a slip of 2.67% on full load. The rotor resistance per phase of the winding is 0.2 ohm. What external resistance per phase must be added in the rotor circuit so that the motor now runs ate a slip of 17.33% such that the torque remains same in both the cases. (Ans: 1.1 ohm)
1.why the slip of induction motor is never zero, 2.what happens if the slip of induction motor is one, 3.what is the value of the slip for an induction motor at on load and full load
1.5 A 10‐pole, 380 ‐V, 50 Hz, D‐connected three‐phase induction motor is rotating a quarry belt conveyor. The machine has the following parameters, referred to the stator, on a per phase basis: Stator Parameters Winding Resistance................0.19 Ω ......... Winding Reactance.................1.12 Ω.......... Rotor Parameters Winding Resistance......................0.29 Ω Winding Reactance.....................1.12 Ω Magnetising Reactance................................16.8 Ω Equivalent Core‐loss Resistance....................900 Ω. The friction and windage losses are 320 W. When the motor runs at its rated slip of 2.6 %. Determine: 1.5.1 The stator current. 1.5.2 Estimate the Output torque of the motor under the rated conditions. 1.5.3 The Motor…
A three phase induction motor with supply frequency of 60 Hz, 8 poles. If the slip is 2.5 % at a certain load, determine (a) the synchronous speed, (b) the speed of the rotor (c) the frequency of the induced e.m.f in he rotor and (d) speed of the induction motor if the slip changes to 6 %
What is the relationship between slip s) and load (Pa) in an induction motor? Please explain.
Example -4. A three-phase. 60-Hz induction motor runs at 890 r/min at no load and at 840 r/min at full load. (a) How many poles does this motor have? (b) What is the slip at rated load? (c) What is the speed at one-quarter of the rated load? (d) What is the rotor's electrical frequency at one-quarter of the rated load?
lap to induce the same voltage if it is wave wound? (Ans. 500 V; 375 rpm) Q 5. A wave-wound armature of a 6-pole generator has 51 slots. Each slot contains 20 conducto voltage required to be generated is 250 V. What would be the speed of coupled prime mover if pole is 0.07 Wb. If the armature is rewound as lap-wound machine and run by same prime move will be the generated voltage? (Ans. 70 rpm; 83.3 V)
3.An induction motor has a rotor resistance and reactance at standstill of 0.1 ohm and 3.5 ohm respectively. At standstill the voltage induced to the rotor is 60volts per phase. If the slip is 5%, determine the rotor current
1- To control the speed of an induction motor, the supply frequency is reduced by 10%. For the same magnetizing current to remain constant, the supply voltage must be....... a) Reduced by 10%, b) Reduced by 20%, c) Increased by 10%, d) Increased by 20% 2. When maximum starting torqua ic ohtoinod
7. A 4-pole, 500V shunt motor has 720 wave connected conductors on its armature. The full-los armature current is 60A and flux per pole is 0.03 Wb. The armature resistance is 0.020 and th contact drop per brush is 1V. then the full-load speed of the motor is -- a) 675 r.p.m. b) 690 r.p.m. c) 705 r.p.m. d) none of the previous,