When a battery is connected to a capacitor (device that stores charge) the charge q builds up -t according to the equation q =qo(1-e), where qo is the maximum charge and r is a constant. At what time t does the charge reach 10% of its maximum value? (Note: Enter your answer in terms of tau, 1, using the Greek letters in MathType.) t10% = S

When a battery is connected to a capacitor (device that stores charge) the charge q builds up -t according to the equation q =qo(1-e), where qo is the maximum charge and r is a constant. At what time t does the charge reach 10% of its maximum value? (Note: Enter your answer in terms of tau, 1, using the Greek letters in MathType.) t10% = S

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter1: Units And Measurement

Section: Chapter Questions

Problem 15P: Use the orders of magnitude you found in the previous problem to answer the following questions to...

See similar textbooks

Similar questions

Hi, I need help solving this question using the diagram below, I got positive values for I1, I2, and I3, but my friends say she got I1 and I2 as negative values and then I3 as positive. R1= 220 ohms, R2 = 330 ohms, R3 = 390 ohms. then v1 is 12 volts.
Consider the figure below. (Due to the nature of this problem, do not use rounded intermediate values in your calculations-including answers submitted in WebAssign.) 0.300 F a (a) Find the charge stored on each capacitor in the figure shown above (C, 11.5 µF, C₂ 9.62 uF) when a 1.62 V battery is connected to the combination. Q₁ What is the total charge stored in the equivalent capacitor? What are the properties of series and parallel combination of capacitors regarding charge and potential difference? C 2554 S E₁ (b) What energy is stored in each capacitor? E₁ = What is the total charge stored in the equivalent capacitor? What are the properties of series and parallel combination of capacitors regarding charge and potential difference? C С
Consider the diagram below of two square-plate capacitors. For the capacitor on the right, if the voltage is held constant by a voltage source and the plates are separated by a factor xºd, what is the new charge on the plates, Q: after the separation? + Letx-3 Express your answer in terms of Q. For example: 5Q or 5 Q. Do not use or any multiplication symbols. If your answer has a decimal, round to one decimal place. |Q' = ? Q' = ? xd
Please fill out the template with the work for this problem. Note that you need to have a picture, a list of knowns and unknowns, the general equation/s you will use, and the math steps to solve for the unknown, Only plug in the numbers after you have solved for the unknown, and the answer with units included. Problem 1: A negative charge of q = -8.3 × 10-17C and m = 1.2 × 10-26 kg enters a magnetic field B = 1.3 T with initial velocity v = 410 m/s, as shown in the figure. The magnetic field points into the screen. Calculate the magnitude of the magnetic force F on the charge, in newtons.
For each of the capacitors below, calculate the following:(a) The equivalent capacitance for this circuit. (b) The potential drop across each capacitor. (c)Thecharge stored in each capacitor. Here, ?1 = 10 ??, ?2 = 10??, ?3 = 10?? . (Hint: You don’t need to docomplicated math here).a) _______________b) _______________c) _______________
Hi I'm given the diameter of the sphere is 25cm. An electric pen brought near this sphere causes a voltage of 5000 V. The distance between the sphere and the pen is 14cm. The pen itself is measured at 25cm. they want to know what is the charge on the sphere? Please break it down so I can understand. The last answer had the wrong diameter calculated into the problem and was missing what formulas they used for each problem and how they solved it in steps.
Part a: what is the equivalent capacitance of the circuit shown above? Give your answer in microfarads. part b: what is the charge on the 4.0 mu*F capacity? Give your answer in microcoulombs par t c:What is the voltage on the 4mu*F capacitor ? Give your answer in Volts part c What is the voltage on the 2.0uF capacitor? Give your answer in Volts part d :
When providing numerical answers you may express them using scientific notation. Express values to four significant figures and use the values of physical constants as provided in the course notes. A parallel plate capacitor has plate areas of 1 cm?, a plate separation of 0.025 mm, and is filled with a material with relative permittivity of 121. Capacitor characteristics Determine values for the capacitance, stored-charge and magnitude of the E-field inside the capacitor when it is directly connected to a 8 V battery. Note, the standard units may not be options provided, but at least one option is suitable for the calculated quantity. Stored charge stored energy=
Time t(s)| Potential Difference V(t) Time t(s) Potential Difference V(t) OV 40 1.328 V 0.332 V 50 1.386 V 10 60 0.638 V 1.422 V 15 70 0.861 V 1.437 V 20 1.017 V 80 1.448 V 25 90 1.458 V 1.131 V 30 100 1.220 V 1.458 V Table 2. Voltage-Time table for Discharging Capacitor Time t(s)| Potential Difference V(t) Time t(s) Potential Difference V(t) 1.479 V 40 0.119 V 5 1.136 V 50 0.057 V 10 60 0.830 V 0.026 V 15 0.602 V 70 0.005 V 20 0.441 V 80 0.002 V 25 90 0.317 V 0.001 V 30 100 0.228 V 0.001 V
Use the orders of magnitude you found in the previous problem to answer the following questions to within an order of magnitude. (a) How many electrons would it take to equal the mass of a proton? (b) How many Earths would it take to equal the mass of the Sun? (c) How many Earth-Moon distances would it take to cover the distance from Earth to the Sun? (d) How many Moon atmospheres would it take to equal the mass of Earth’s atmosphere? (e) How many moons would it take to equal the mass of Earth? (f) How many protons would it take to equal the mass of the Sun? For the remaining questions, you need to use Figure 1.4 to obtain the necessary orders of magnitude of lengths, masses, and times.
ons ents ations In the circuit shown below, V = 26 V, I = 3A, R1 = 29 2 and R2 = 17 Q. Using either superposition or nodal analysis, calculate the voltage, Vx (in Volts to 1 decimal place) and enter the value in the answer field below. Your handwritten working to this question should be uploaded R1 Vx 500 R2
For the four capacitors in the circuit shown inthe figure below, CA = 1.00 F, CB = 4.00 F, CC =2.00 F, and CD = (first two digits from your university I.D.) F. What is the equivalent capacitance between points a and b?