what is the part of the spring being compressedor stretched upon application of force

Q: Critical damping of the system ?

A: Given: Mass,m=13.8 kgSpring stiffness,k =1365 N/mDamping coefficient=17 Ns/mCritical damping of the…

Q: Davit- Pulley Pin- Cable- a

A: dp=20mm=0.78inα=15°Tmax=8kN=1798lbζp=27.5MPa=3988.538psiWL=6.7kN=1506.12lb

Q: Type of Mechanism

A: As given in question we have to match the following mechanism; hence; (P) SCOTT (Q) Geneva mechanism…

Q: critical damping of the system ?

A: Given: A vibratory system consists of a mass,m=13.5 kgSpring stiffness,k=1355 N/mdamping…

Q: b) Based in the stuck pipe case in the last page answer the following questions: i. What do you…

A: Question no 1 solved  As it contains multiple questions, if want any specified question to be solved…

Q: What would be the stretched length in spring (AB)?

A:

Q: What is the force output of a cylinder that has a 1” bore and operated at 600 psig?

A:

Q: life of the ball bearing w

A: Given; Load reduced to half on the ball bearing, then life of the ball bearing will be  ?

Q: Members that are joined together to form a kinematic chain Link Bar Pin Joint

A: As per company's guidelines we can answer only first question.

Q: spring as alculate the true load and load force when the indic

A: given:m1=10gw1=0m2=60.3gw2=50gw3=100g

Q: (a) Define mechanical advantage and disadvantage. (b) Give an example of a lever in the body that…

A: (a) Mechanical advantage of a lever is the ratio of the length of the lever on the effort side of…

Q: What other name is used to describe the vibration damper?

A: What other name is used to describe the vibration damper?

Q: tion crea

A: This statement is (False)

Q: What is the degree of freedom of the mechanism?

A: A mechanical system's degrees of freedom (DOF) are the number of independent characteristics that…

Q: een two rigid immo gure. The rod is pe

A:

Q: The high tension side of belt is known as tight side Select one: True

A: Given: Belt pulley system

Q: 6. Vibration absorber attachment to the system will create 3 new natural frequencies *

A: Given: Single degree of system A vibration absober added to the system To determine: How many new…

Q: What additional force A is needed to keep the block in static equi

A: The calculated additional force is needed to keep the block in static equilibrium.

Q: On a helical compression spring, the direct shear stress is greater than the torsional shear stress.

A:

Q: 1- When damping ration > 1 this case called. a) Over damping b) under damping c) Critical damping d)…

A: Option A  is correct  (over damping)

Q: the following shadec

A: given:

Q: Q8/ . .. lumped on the axis of piston pin axis * Reciprocating parts REDUCED SYSTEM piston travel…

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: et what is the stretch in the spring wvhen the system is in equilibrium?

A:

Q: What is the standard 10 lb deflection amount for a properly tensioned belt that spans 42”?

A: Given data:- Length = 42" Tension = 10lb  Find:-  Deflection amount?

Q: specification required for the bolt

A: Given; Three bolt system as shown in figure;The bolt material has ,shear yield…

Q: e spring force and deflection of t

A: max.  spring displacement -1.1302 in max spring force -141.908 lbf

Q: 1) Draw a simple sketch of your regulator design 2) Draw a simple sketch of the spring

A:

Q: What happens when the member is confined?

A: Confined member: If a member is confined then it means it is fixed to a position.

Q: While discussing types of coil springs: Technician A says that linear-rate coil springs have equal…

A: Technician A:- Technician A is correct says that in case of linear-rated coil springs have equal…

Q: Match the symbol to the component: а. Pump b. Motor c. Cylinder with retract cushion d. Pressure…

A:

Q: gative loop of the indicator diagram Spring cons,

A:

Q: change in spring stiffness is?

A: Given: If the wire diameter of a compressive helical springs is increased by 2%,We have to find then…

Q: G) bore and stroke of compressor in mm (k) power of motor to drive the compressor

A:

Q: What is the equivalent stiffness of the springs in the system?

A: Disclaimer: Since you have asked multiple questions, we will solve the first question for you. If…

Q: Which is procedure provides a method that may be used to determine the displacement of any joint on…

A: We can use the method of virtual work to determine the displacement of a truss joint when the truss…

Q: life of the ball bearing

A: Given: If the load on a ball bearing is reduced to half, the life of the ball bearing ? Therefore;…

Q: What is another name for the diaphragm spring?

A:

Q: M25x6-4h5h-23   describe each part

A:

Q: l the spring be compressed?

A: x= 13.717cm

Q: The variable which is to be controlled is known as

A: The variable which is to be controlled should remain the same, thus it is known as constant…

Q: How many spring balance used in Wall jib Crane experiment? O a. 4 O b. 2 O .1 O d. 6

A: In a Wall jib crane experiment two spring balance are used. (option-b)

Q: Which of the following is NOT a spring type used in pressure plate assemblies?

A: Diaphragm is not a spring type used in pressure plate assemblies.

Q: Describe uncontrolled spring action without a shock absorber.

A: Function of shock absorber:  A shock absorber is also known as damper. it is a mechanical device…

Q: iii. The piston rings. a. is used to withstand the pressure of gas in the cylinder b. acts as a…

A: As per the guidelines we will answer the first three questions for you. For the rest of the…

Q: The clutch, or friction, disc is connected to the

A: The clutch, or friction, disc is connected to the....

Q: ht, what is the tension in the wire?

A: To find tension ( T)

Q: From the table below, what is the initial tension required for the spring in letter (D): Hooke's Law

A: Given   Force constant, k = 10 N/m         Elongation, x = 0.52 cm                              =…

Q: True or False:  The opposing torque is inversely proportional to the elasticity of the torsional…

A: