What is hysteresis? A) Hysteresis is when the measuring device shows a value below or above the value to be measured due to friction, magnetic effect, thermal effect etc. B) The measurement of the measuring device in accordance with the standards is called hysteresis. C) The ability of the measuring instrument to measure the physical size in a stable way is called hysteresis. D) The ability of the measuring instrument to keep its metrological properties constant is called hysteresis. E) The ability to measure the physical size of the measuring instrument at the same value over and over again is called hysteresis.

What is hysteresis? A) Hysteresis is when the measuring device shows a value below or above the value to be measured due to friction, magnetic effect, thermal effect etc. B) The measurement of the measuring device in accordance with the standards is called hysteresis. C) The ability of the measuring instrument to measure the physical size in a stable way is called hysteresis. D) The ability of the measuring instrument to keep its metrological properties constant is called hysteresis. E) The ability to measure the physical size of the measuring instrument at the same value over and over again is called hysteresis.

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter2: Measurement, Materials, And Safety

Section2.5: Quality Assurance, Process Planning, And Quality Control

Problem 5RQ: What is the important factor to consider when choosing the proper measuring tool to inspect a...

See similar textbooks

Similar questions

Discussion: 1) discuss the methods of measurement and what is the accurate method. 2) What is the micrometer .and what are the types and uses of each type? 3) Specimen Dimension to Dimension Dimension be measured Measured Measured by Vernier by ruler External diameter Internal diameter Thickness Length 4) Do you have another method or appearance that may be used in measurement ?
a) What is the difference between accuracy and precision of a group of measurements? b) What is the most probable value of a group of measurements?
QUESTION 4 a) Define the following terms and describe the relationship between these two elements in carrying out measurement activity: (i) Accuracy (ii) Precision b) Convert pressure reading of 0.01 Pa in ton/m.h?. c) Briefly describe the difference between systematic error and random error. *You are free to use any example/measuring equipment to answer the question
What is the algebraic difference between the lowest limit of size dmin and the nominal size da (dmin – da)? 1) the tolerance 2) the upper deviation es 3) fit 4) the lower deviation ei.
Which of the following terms/ phrases describes the accuracy of measurement? a Depends on the instruments used b Standard deviation c Experimental error /Percent error d Reproducibility of a set of measurement
a) Name two groups of standards in addition to national, industry-wide standards and where they are valid. b) Which three options exist for defining dimensional tolerances in a technical drawing?
Q1: Select the correct answer. up to A. Resilience is the energy absorbed by the material a. yield. b. ultimate sensile stress. c. fracture. B. The grain boundaries are a. less chemically active than grains themselves. b. the regions of orientation mismatch of the neighbouring grains. c. classified as linear defects. C. All polycrystalline materials are considered as isotropic because a) they have crystallographic direction-mechanical properties independence relation b) all the crystals' orientations are the same c) the random direction of many grains cancels the anisotropic effect D. Dislocations slip process in metallic crystalline materials a) is essential to explain why the metals exhibit much lower strength than that theoretically predicted based on metallic bonding. b) makes metals and alloys brittle. c) cannot be used to control the mechanical properties of metallic materials E. The atomic stacking ABCABCABC is for d) FCC crystal structure e) BCC crystal structure f) HCP crystal…
Information such as tolerances and scale can be found in the________ of an engineering drawing.
What is the important factor to consider when choosing the proper measuring tool to inspect a dimension?
In the context of our teaching and learning, which one of the below statements is mostly correct about in the creation of detailed design of a component? In deciding the tolerance, the guidance is the tighter the better. I am the designer, so I decide the required tolerance as l like. The tolerance is determined by the function. The chance to manufacture component to the exact size is like to win a lottery. I would enjoy winning a lottery, so I should specify all the dimensions as exact, no tolerance to be considered at all.
12)Among the following, which technique can be used for 3D deformation measurement purpose? O Ruller Stereoscopic video imaging system O Dial gauge Straight edge set
Subject: Mechanical Measurements