Water is being heated in a vertical piston-cylinder device. The piston has a mass of 40 kg and a cross-sectional area of 150 cm2. If the local atmospheric pressure is 100 kPa, determine the temperature at which the water starts beiling

Water is being heated in a vertical piston-cylinder device. The piston has a mass of 40 kg and a cross-sectional area of 150 cm2. If the local atmospheric pressure is 100 kPa, determine the temperature at which the water starts beiling

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter9: Heat Transfer With Phase Change

Section: Chapter Questions

Problem 9.26P

See similar textbooks

Related questions

Q: A 1.2-m-diameter, 3-m-high sealed vertical cylinder is completely filled with gasoline whose density…

A: To proceed the following assumptions are taken into consideration 1)The Liquid in the container acts…

Q: A capillary tube is immersed vertically in a water container. Knowing that water starts to evaporate…

A: At the liquid side of the meniscus, the pressure P is 2 kPa. Write the expression of capillary rise…

Q: Determine the pressure in a 1 m³ vessel containing 1.9135 kg of superheated steam at 300 °C.

A: given data volume = 1 m^3 mass = 1.9135 kg temperature = 300°C find the pressure of superheated…

Q: What is a manometer? What are the two types of manometers? What is a thermocouple? What is a…

Q: Taking the coefficient of compressibility of water to be 2200 MPa, determine the pressure increase…

A: Given Coefficient of compressibility, B = 2200 MPa Change in volume, dV1 = 1% =…

Q: Milk with a density of 1020 kg/m3 is transported on a level road in a 9-m-long, 3-m-diameter…

A: Given that,

Q: A vertical piston-cylinder device contains a gas at a pressure of 105 kPa absolute. The piston has a…

A: Given , pressure of the gas P=105kPaPressure inside the cylinder by gas is balanced by the local…

Q: Determine the height of the fluid inside a manometer that is attached to a CO2-filled tank. The…

Q: If the pressure of a substance is increased during a boiling process, will the temperature also…

A: When pressure of a substance is increases during boiling process then the temperature will also…

Q: What happened to the surface tension of liquid when the temperature increase ?

A: The surface tension is depends upon the intermolecular force.

Q: Determine the density, specific gravity, and mass of the air in a room whose dimensions are 4 m × 5…

A: Volume, V= 4 m × 5 m × 6 m= 120 m3 Pressure, P= 100 kPa Temperature, T= 25°C= 25 + 273 K= 298 K…

Q: Determine the density of the liquid? The mass flow rate of the liquid is 4800 kg/s. And the velocity…

Q: Nitrogen is contained in a 4 m^3 rigid vessel at a pressure of 4200 kPa. Determine the mass if the…

A: The value of characteristics gas constant for nitrogen gas is: R=RM=8.31428=0.297 kJkg·K Convert the…

Q: A hydraulic lift is to be used to lift a 550 kg weight, the piston-cylinder of the hydraulic lift…

A: Given Data The mass of the piston, mp=6Kg The mass of the load, mL=550Kg Diameter of the piston,…

Q: A 4.5 m-diameter vertical cylindrical milk tank rotates at a constant rate of 15 rpm. If the…

A: Given:- The angular velocity of a cylinder is expressed by:

Q: The analysis of a propeller that operates in water at 60°F shows that the pressure at the tips of…

A: cavitation –it is a phenomenon due to which a rapid change in the pressure of the liquid leads to…

Q: Water in a rigid container has a pressure of 1000 kPa and specific volume of 0.1 m3/kg . The quality…

Q: A rigid tank contains 20 lbm of air at 20 psia and 70°F. More air is added to the tank until the…

Q: Determine the height of the fluid inside a manometer that is attached to a CO2-filled tank. The…

A: Pressure is defined as the force per unit area. there are two types of pressure absolute pressure…

Q: 2. A U-tube is made up of two capillaries with bores of 0.0039 ft and 0.0078 ft. A liquid with a…

Q: What does the coefficient of volume expansion of a fluid represent? How does it differ from the…

A: Coefficient of volume expansion The coefficient of volume expansion shows the variation of the…

Q: An air-conditioning system requires a 35-m-long section of 15-cm-diameter ductwork to be laid…

A: Given: The length of the duct is L=35 m. The diameter of the duct is D=15 cm. The density of the…

Q: A storage tank contains 29 kg of nitrogen (N2) at an absolute pressure of 111 kPa and a temperature…

Q: Determine the specific volume of refrigerant -134a at a temperature of 5°C and a quality of 70%.

Q: A vertical frictionless piston cylinder contains air at a pressure of 300 KPa with atmospheric…

Q: A 4-m-diameter vertical cylindrical milk tank rotates at a constant rate of 15 rpm. If the pressure…

A: Angular velocity of the cylinder is calculated as, ω=2πN60=2π×1560=1.5 rad/s The equation of height…

Q: A U-tube is made up of two capillaries with bores of 0.0039 ft and 0.0078 ft. A liquid with a…

A: Answer: The density of the liquid is 943.2875 kg/m3.

Q: A glass tube is attached to a water pipe, as shown in the figure. If the water pressure at the…

Q: Consider a U-tube whose arms are open to the atmosphere. Now water is poured into the U-tube from…

A: Given, Density of oil, ρo=790 kg/m3 Let height of water in left arm of U tube , hw=70 cm=0.7 m Oil…

Q: A 5-m³ rigid insulated tank is connected through a valve to a supply line that carries steam at…

Q: A rigid tank holds 20 lbm of air at a pressure of 20 psi and a temperature of 70°F. Increase the…

Q: B 0.4 m Oil 0.3 m Gasoline -Mercury

Q: Taking the coefficient of compressibility of water to be 7 × 105 psia, determine the pressure…

A: Given data: The compressibility of water, k = 7 × 105 psia. (a) When volume of water is reduced by…

Q: A 5-m-long, 4-m-high tank contains 2.5-m-deep water when not in motion and is open to the atmosphere…

A: The diagram of the water level in case of acceleration in x-direction, The angle is calculated as,…

Q: An air-conditioning system requires a 35-m-long section of 15-cm diameter duct work to be laid…

Q: The lower half of a 10 m high cylindrical container is filled with water and the upper half with oil…

Q: Determine the internal energy of saturated liquid water at 225 kPa.

A: Given data: Saturated liquid water at 225 kPa

Q: The helium-filled blimp shown in the figure below is used at various athletic events. Determine the…

A: Given data: p=14.2 psiaT=80°FR=1.242×104 ft·lbf/slug·R Need to determine the number of pounds of…

Q: The distance between the centers of the two arms of a U-tube open to the atmosphere is 30 cm, and…

Q: oble with a diameter of 2.72" is to be enlarged by blowing air into it. If the surface tension of…

A: D1= 2.72" D2= 3.64" (Surface Tension) T= 0.0035 lbf/ft To find :- Work input required.

Q: Determine the atmospheric pressure at a location where the barometric reading is 735 mmHg. Take the…

A: Given: The barometric reading is hbar=735 mmHg. The density of the mercury is ρ=13600 kg/m3. The…

Q: Using average specific heats, explain how enthalpy changes of ideal gases and incompressible…

A: The enthalpy of an ideal gas is defined as the energy associated with it by virtue of its motion. It…

Q: Determine the pressure difference between the inside and outside of the 0.15 mm diameter air bublle…

A: GiveDiameter of the air bouble, d=0.15mmsurface tension σ=0.111N/m

Q: Describe incompressible substances and determine the changes in their internal energy and enthalpy.

A: given: Describe incompressible substances and determine the changes in their internal energy and…

Q: Determine the density of water vapor 250 kPa gage and a temperature of 20°C if the gas

Q: mass of air in the tank

A: Given: V= 10 cubic meter P=500 kPa T=40oCTo determine: Mass of the air

Q: One pound-mass of water fills a 2.29-ft3 rigid container at an initial pressure of 250 psia. The…

A: Given:Mass of water,m=1 lbmVolume of rigid container,V=2.29 ft3Initial pressure,P1=250psiaFinal…

Q: Water is being heated in a vertical piston–cylinder device. The piston has a mass of 40 kg and a…

A: For a vertical cylinder device a vertical downward atmospheric pressure force and a weight acts on…

Q: A 1.2 mm diameter glass tube is inserted into water at 20°C in a tank. Determine the capillary rise…

Question

Water is being heated in a
vertical piston-cylinder device.
The piston has a mass of 40 kg
and a cross-sectional area of
150 cm2. If the local
atmospheric pressure is 100
kPa, determine the temperature
at which the water starts
boiling.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

If the pressure of a substance is increased during a boiling process, will the temperature also incre ase or will it remain constant? Why?
Water is to be boiled at atmospheric pressure in a polished copper pan by means of an electric heater. The diameter of the pan is 0.48 m and is kept at 108 deg C. What is the power required to boil the water? Tsat 100°C; Properties of water at 100°C: Density. pl= 961 kg/m3; Kinematic viscosity, v 0.293x10-6 m2/s: Prandti Number. Pr 1.740; Specific heat, Cpl = 4216 J/kg.K; Dynamic viscosity, u = p x v = 961 x 0.293 x 10-6 = 281.57 x10-6 Ns/m2; hfg = 2256.9 k/kg; pv = 0.597 kg/m3; a = 0.0588 N/m; Csf=0.013; n=1:
Stato the minimum diametor of glass tube to be immersed in water, for which capillary offects are to be limited upto 2.98 mm. Take surfaco tonsion of water in contact with air as 0.073 N/m.
Consider a tank with surface area A.(m2) It containsa fluid of M(kg) at an initial temperature of T0. (C) The specific heat of the fluid is Cp. (J/kg) The fluid inside the tank is heated with condensing vapour outside at temperature of Ts. find the equation that gives the change of the temperature of the fluid in the tank with time.T=f(t) neglect donduction heat transfer h=heat transfer film coef. homogenous T through the tank
The pressure on the suction side of pumps is typically low, and the surfaces on that side of the pump are susceptible to cavitation, especially at high fluid temperatures. If the minimum pressure on the suction side of a water pump is 0.51 psia absolute, determine the maximum water temperature to avoid the danger of cavitation. Find the maximum water temperature to avoid the danger of cavitation (in ºF).
2.0 Air is cumpressed in a diesel engine from an initial pressire of 13 psia und a temperature of 120 "Fts one - twelfh of its origmal volume. Caleulate the tinal semperature assuming the compression to be adiabatic. Answer 1107 °F
The densiaies of two ligeids A and 1B are gileen as lo00trg/m² and 6ookg/ms respectivrely.Ih tevo liquids. are mixed ma certain propertion cend the denSity op the resulting liquid is 85olig/m3. Holo much of liquidn (in graims) does rg ef the mixture cantain! Asqume the llelum e of the two lifuids is additivee when mixed.
How does the pressure vary at depth (Z) in liquid and gaseous fluids, and explain the reasons why there are differences.
The critical temperature of gas TOS is -46 deg Celsius. If the value of its Van der Waals constant b is 2.1 x 10 -5 m3/n, find the value of its VDW constant a in Pa-m6/n2
Identify the state of the fluid: Water at 19.94kPa, with a temperature of 60°C
cenical body is made to rotate d a constent visesity A A film of oil having of oro02 NS/m² seperates the cone from the container. What to rque is required to maintain this motion. The cone has a eol m tall. s peed of to rad/s a The fi lm thickness is 0:25 mm ra dius at the base and is P10 rad/s 025 film
A 2.5-m-tall steel cylinder has a cross-sectional area of 1.5 m2. At the bottom, with a height of 0.5 m, is liquid water, on top of which is a 1-m high layer of gasoline, relative density of 0.8. The gasoline surface is exposed to atmospheric air at 101 kPa. What is the gage pressure at the liquid interface? what is the answer? a.0.077 atm b.15.839 psi c. 1.139 mmHg d.108.848 kPa