Water from a reservoir is raised in a vertical tube of internal diameter D = 45 cm under the influence of the pulling force F of a piston. Determine the force needed to raise the water to a height of h = 1.5 m above the free surface. What would your response be for h = 3 m? Also, taking the atmospheric pressure to be 96 kPa, plot the absolute water pressure at the piston face as h varies from 0 to 3 m. h D Air Water

Water from a reservoir is raised in a vertical tube of internal diameter D = 45 cm under the influence of the pulling force F of a piston. Determine the force needed to raise the water to a height of h = 1.5 m above the free surface. What would your response be for h = 3 m? Also, taking the atmospheric pressure to be 96 kPa, plot the absolute water pressure at the piston face as h varies from 0 to 3 m. h D Air Water

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter7: Seepage

Section: Chapter Questions

Problem 7.1P

See similar textbooks

Similar questions

Problem 4. The open tank shown in the figure have 2 piezometers attached on one side, containing two different liquids, A (SG=0.83) and B (SG=2.50). Find the (.- El 5m a. elevation of liquid surface in piezometer B b. total pressure at the bottom of the tank. Liquid A El Im Liquid B El Om
(4) Consider that we have a horizentral pipe, like shown in the sketh, which is carrying in this case, cooling water at 10 °C. The elevation of the big tank of cooling water is 100 m, the elevation of the center line of the pipe is 20 m, the length of the pipe is 2000 m. Head loss in the pipe is 0. 07 L / D) V? H. D=20 cm, the rate of flow is 0.0 a=1 ase calculate the 2g pressure in the pipe. Elevation = 100 m Elevation = 20 m L=2000 m %3D II ||
A water siphon having a constant inside diame of 3 in. is arranged as shown in the figure below the friction loss between A and B is 0.8V²/2 wh is the velocity of flow in the siphon, determine flowrate involved. Assume a = 4 ft, h = 12 ft. D-- B a h
2. The suction pipe of a pump rises at a slope of 3 vertical in 4 along the pipe which is 12 cm in diameter. The pipe is 7.2 m long; its lower end being just below the water surface in the reservoir. For design reasons, it is desirable that pressure at inlet to the pump Pump 4/3 shall fall to more than 75 kPa below atmospheric pressure. Neglecting friction, determine the maximum discharge that the pump may deliver. Take atmospheric Suction pipe pressure as 101.32 kPa. F.W.S. Reservoir/sump 2. 7.2 m
Situation XX: In the figure shown, z, = 4 m, length of pipe from the reservoir to the pump is 120 %3D m, from the pump to the nozzle is 1000 m. The diameters of pipes are 0.60 and 0.45 m respectively. The gage pressure at B (the suction side of the pump) is -64 KPa. Neglect minor losses. В C P. 0.45 m diam. LCD = 1000 m %3D Zp = 4 m f = 0.02 0.60 m diam. LAB = 120 m f = 0.02 %3D 52. Compute the velocity of water in pipe AB. a. 2.297 m/s b. 1.452 m/s c. 3.147 m/s d. 2.672 m/s 53. Compute the velocity of water in pipe CD. a. 1.23 m/s b. 4.08 m/s c. 3.56 m/s d. 5.59 m/s 54. Compute the discharge of the pipe from A to B due to pumping. a. 0.65 m3/s b. 0.45 m3/s c. 0.89 m³/s d. 0.25 m3/s 60 m, f= 0.02 m and loss of head ith
Situation 1: In the pipe system shown, the velocity of water in pipe A is 1 m/s. The friction factor f = 0.02 for all pipes. a. Determine the discharge in pipe B. b. Determine the velocity in pipe C. c. Determine the headloss in pipe E. d. Determine the difference in elevation of the two reservoirs. Water D A 300 m 200 mm D 300m 500 mm Diom 600m 300mm Diam 300m 300mm D B 800 m 300mm Diam E
Show the necessary figures (if applicable) 2.3) A pipe discharges 142 lps of water into a reservoir at a point 1.85 m below the water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm.If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
Water flows into the atmosphere from a nozzle and strikes a vertical plate as shown in the figure below. A horizontal force of 12 N is required to hold the plate in place. Determine the reading on the pressure gage. Assume the flow to be incompressible and frictionless. (Dı=0.3 m, D2=0.1 m, F=12 N) P=? F A2 A1
0.12 O -0.12 8.33 (1) Darcy Experiment A set-up of Darcy Experiment involves measuring the pressure head at two piezometers separated a distance, L. Given the set-up shown, determine the hydraulic gradient if the hydraulic head at (1) is 66 cm, hydraulic head at (2) is 54 cm, and the travel distance is 100 cm. O-8.33 -L h e - - - -
A pitot tube is inserted in a pipe of 30 cm diameter. The static pressure of the tube is 10 cm of mercury, vacuum. The stagnation pressure at the centre of the pipe recorded by the pitot tube is 1.0 N/cm². Calculate the rate of flow of water through the pipe, if the mean velocity of flow is 0.85 times the central velocity. Assume coefficient of the tube to be 0.98.
-8.33 -0.12 8.33 (1) 0.12 -L Darcy Experiment A set-up of Darcy Experiment involves measuring the pressure head at two piezometers separated a distance, L. Given the set-up shown, determine the hydraulic gradient if the hydraulic head at (1) is 66 cm, hydraulic head at (2) is 54 cm, and the travel distance is 100 cm. h (2) e - - - -
4.80 Water (p = 62.4 lbm/ft³) flows from the large orifice at the bottom of the tank as shown. Assume that the flow is irrotational. Point B is at zero elevation, and point A is at 1 ft elevation. If VA = 4 ft/s at an angle of 45° with the horizontal and if VB = 12 ft/s vertically downward, what is the value of PA - PB? Answer B Vertical Problem 4.80 45°