Water flows in the upward direction in a tank through 2.5 m thick sand layer as shown in the figure. The void ratio and specific gravity of sand are 0.58 and 2.7, respectively. The sand is fully saturated. Unit weight of water is 10 kN/m³.

Water flows in the upward direction in a tank through 2.5 m thick sand layer as shown in the figure. The void ratio and specific gravity of sand are 0.58 and 2.7, respectively. The sand is fully saturated. Unit weight of water is 10 kN/m³.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter9: In Situ Stresses

Section: Chapter Questions

Problem 9.12P

See similar textbooks

Similar questions

A ground profile consists of 2m silty sand underlain by 3m of clay. The ground water table is 3m below the ground surface. The sand has a unit weight of 14kN/cum. The clay has a unit weight of 16kN/cum above the water table and 20kN/cum below the water table. Determine the Total stress at the surface of the water table (kPa). Determine the effective stress at the bottom of the clay layer (kPa). Determine the effective stress 1m from the bottom of the clay layer (kPa). Please answer this asap. For upvote. Thank you very much
2. The depth of water in a well is 3 m. Below the |IAVA bottom of the well lies a layer of sand 5 meters thick overlying of the clay deposit. The specific clay a gravity respectively 2.64 and 2.70. Their water contents are respectively 25 and 20 percent. Compute the total stress, effective stress and the pore water pressures at pointS solids of sand and are 3m A and B of the figure shown. Sand 5 m A• Ans: 88 kN/m², 29.1 kN/m², 58.9 kN/m² $2 m 12 m Clay
PROBLEM 1: A layer of sand 4.5m thick with specific gravity of 2.60, degree of saturation of 85%, and porosity of 41.18% with a 5 m thick of clay with specific gravity of 2.65 and a water content of 0.28. Ground water table is located at the interface of the two soils. Compute the depth below the ground surfac would the effetive stress be 100kPa. B. Compute the effective stress at a depth 8m below the ground surface. C. Compute the depth of excavation required to reduce the effective stress by 60 kPa
surface layer QY A Soil profile consists of a surface of Line sand 6m thick with unit weight of 16-5 kN/m³ and clay layer of 8m thick beneth the Sand layer. the water table is located at adepth of 4m below the ground surface: submergend for line Sand is 10.4 kN/m², Gs love clay layer is 2.7 & wc %. = 30% Calculate the eflective stress at the middle of clay Layer. + 6m 4M DW.T Fine Sand 8m clay 8=165& M2 sub = 1o.y tw G3=2=7 w;. = 30%.
geotech. engineering A Thick layer of clay underlies a sand formation having a thickness of 4m. the groundwater is located 2m below the ground surface. The specific gravity of sand and clay is 2.65 with sand having an average void ratio of 0.52. the clay has a water content of 42%. Degree of saturation above the water table is 0.37. a. Compute the moist unit weight of the sand b. Total stress at a depth 10 m below the ground surface c. Effective stress at a depth of 10 m below the ground surface
Determine: (a) the capillary height h, of the rise of the moisture into the sand stratum above the water table, and (b) determine the resulting negative porewater pressure u. fine sand d=0.30 man G₁=2.66, a=0.55, S-50% zone of capillary rise saturated clay G₂-271 ke + pore pressure +he WT
The profile at a site consists of 5m of sand overlying 10m of compressible clay, which in turn overlies a dense sand. The water table is at the top of the profile. The total unit weight of the top sand is 19kN/m3 and that of the clay is 18kN/m3. The Cv of the clay is estimated to be 5x 10-3 cm2/sec. Initially the clay is normally consolidated. It is planned to place a temporary fill that will exert a vertical load of 200kPa over the entire site. How long must the fill be in place so that, after it is removed, the maximum past pressure at every point in the clay is at least 50kPa larger than the vertical effective stress that existed before the fill was placed?
11. Consider the downward flow of water through a layer of sand in the tank shown. (see picture below) Void ratio of the soil = 0.52 Specific Gravity = 2.70 Compute the value of h1. (Answer: 0.436) Compute the effective stress at A. (Answer: 17.44 kPa) Compute the effective stress at B. (Answer: 31.98 kPa) Compute the seepage force per unit volume. (Answer: 3.57 kN/m3)
Table 1.2 Layer No. Thickness, H Soil Parameters e = 0.51, Gs = 2.52 e = 0.56, Gs = 2.65, S = 61% w = 20%, e = 0.51 1 6.2 ft 2.1 ft 3 3.56 m H2 | Dry sand | Clay; zone of capillary rise Clay Rock Determine: a.Effective stress at ground water surface. b.Effective stress at the immediate zone of capillary at clay layer below the dry sand. c.Effective stress at the interface of clay and rock layer.
The soil profile at a site consists of 10 m of gravelly sand underlain by a soft clay layer. The water table lies 1 m below the ground level. The moist and saturated unit weights of the gravelly sand are 17.0 kN/m3 and 20.0 kN/m3, respectively. Due to some ongoing construction work, it is proposed to lower the water table to 3 m below the ground level. What will be the change in the effective stress on top of the soft clay layer?
The soil profile at a site consists of 10 m of gravelly sand underlain by a soft clay layer. The water table lies 1 m below the ground level. The moist and saturated unit weights of the gravelly sand are 17.0 kN/m3 and 20.0 kN/m3, respectively. Due to some ongoing construction work, it is proposed to lower the water table to 3 m below the ground level. What will be the change in the effective stress on top of the soft clay layer?
The ground water table in a deep deposit of sand is located at 4 m from the ground level. Due to capillary action, sand is saturated for a height of 1 m from the water table. The degree of saturation of the sand above the capillary fringe is 40%. If the specific gravity of solids and average void ratio of the sand are 2.68 and 0.72 respectively. Determine the effective stress (in kPa) at 4 m and 10 m from the ground level. Consider the standard value for unit weight of water.