Water flows as two free jets from the tee attached to the pipe shown in the figure. The exit speed is 15 m/s. If viscous effects and gravity are negligible, determine the x and y components of the force that the pipe exerte on the tee. V = 15 m/s Area = 0.3 m² Area = 1 m² V = 15 m/s ·X Area = 0.5 m² Tee Pipe

Water flows as two free jets from the tee attached to the pipe shown in the figure. The exit speed is 15 m/s. If viscous effects and gravity are negligible, determine the x and y components of the force that the pipe exerte on the tee. V = 15 m/s Area = 0.3 m² Area = 1 m² V = 15 m/s ·X Area = 0.5 m² Tee Pipe

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A circular balloon is being filled through the inlet, which has a cross-sectional area denoted as A1. The air enters the balloon with a velocity V1 and a density ρ1. If the balloon radius is denoted as R, and the densitywithin is taken as an average value ρavg, construct an expression for the time rate of change of mass withinthe balloon.
Determine the exit velocity V2 for the given data V1 = 20 m/s, Q3 = 0.01 m3/s, and dh/dt = 0.
A pipe of diameter 10cm conveying 200 liters/s of water has bend of angle (θ = 90⁰) and θ = 0⁰ through horizontal plane. Find theresultant force exerted on the bend if the pressure at the inlet and outlet of the bend are 15N/cm2 and 10 N/cm2respectively
A piston 46mm in diameter slides concentrically in a fixed cylinder 50mm in diameter. The cylinder is filled with water and when the piston moves into the annular gap, water flows through the annular gap surrounding the piston. If the velocity of piston is 75mm/s raletive to the cylinder, determine the velocity of flow through the gap.
Water flows at a rate of 3 m3/s through a 300 mm diameter pipe in which there is a 90o bend. if the pressure at the entrance to the bend is 450 kN/m2 (absolute), determine the total force necessary to anchor (kN) the bend. Friction losses can be neglected.
From point A to point B of the system in the figure flows oil with specific weight 55 lb/ft3 at a rate of 26.2 gallons / minute. Determine the height h.
Water flows from a nozzle with a speed of V = 10m/s Stream diameter = 0.1 m Nozzle -- Moving control volume and is collected in a container that moves toward the V = 10 m/s nozzle with a speed of Vcy = 2 m/s as shown in the figure. If the water between the nozzle and the tank is in the constant diameter stream, what is the accumu- V = 2 m/s 3 m lation rate of water in the tank?
Water discharges into the atmosphere through the device shown in the picture. Determine the strenght component in the x direction on the flange required to mantain the device on it's place. Ignore the effect of gravity and friction. Express the result in lb.
If the static pressure of that fluid in the pipeline is 4.3 ´ 104 Pa while its total pressure is 4.7 ´ 104 Pa, determine the kinetic energy per unit volume of the fluid. Assume that the fluid is incompressible and non-viscous. Consequently, calculate the volume flow rate in the pipeline. Take density of the fluid to be 103 kgm-3and the cross-sectional area of the pipeline as 20 cm2.
The gauge pressure of water at A is 150.5 kPa. Water flows through the pipe at A with a velocity of 18 m/s, and out the pipe at B and C with the same velocity v. Neglect the weight of water within the pipe and the weight of the pipe. The pipe has a diameter of 50 mm at A, and at B and C the diameter is 35 mm. Pw = 1000 kg/m³. (Figure 1) Determine the x component of force exerted on the elbow necessary to hold the pipe assembly in equilibrium. Express your answer to three significant figures and include the appropriate units. • View Available Hint(s) ? Fr = Value Units
From the figure, the piston is pushed into the cylinder. If the average speed of Fluid moving up to 5 m/s. Calculate the velocity v of the piston while it is moving into the cylinder.
Water is flowing upward through a tapering pipe of height 1 m at the rate of 0.28 cumec. Thediameters at the lower and upper ends of the pipe are 300 mm and 600 mm, respectively. If pressure atthe lower end of the pipe is 0.981 bar, determine the force exerted on the tapering pipe and itsdirection. Neglect the losses of energy and the weight of the pipe.