Water at a temperature of 25°C flows through a horizontal cast iron pipe (as shown in the following figure) at 0.0314 m³/s. Determine the smallest diameter pipe (in mm) if the allowed pressure drop over a length, L-223 m is to be no more than 80 kPa. Take pw = 997.1 kg/m³ and w = 0.898(10-6) m²/s, and roughness height = 0.00026 m. Note: 1. Take pressure drop at section 1 and section 2 as, P1-P₂ = whL 2. Take f=0.024 for your first assumption 3. Make only two iterations 4. Answer should be in decimal value with two decimal places L

Water at a temperature of 25°C flows through a horizontal cast iron pipe (as shown in the following figure) at 0.0314 m³/s. Determine the smallest diameter pipe (in mm) if the allowed pressure drop over a length, L-223 m is to be no more than 80 kPa. Take pw = 997.1 kg/m³ and w = 0.898(10-6) m²/s, and roughness height = 0.00026 m. Note: 1. Take pressure drop at section 1 and section 2 as, P1-P₂ = whL 2. Take f=0.024 for your first assumption 3. Make only two iterations 4. Answer should be in decimal value with two decimal places L

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A smooth pipe with a constant diameter 0.20 m carries water at a temperature of 30oC (Refer Table Q4(c)). The Pipe pressure at section 1 and section 2 is 50 kPa and 20 kPa, respectively. Section 1 is located 2 m lower than section 1. Determine the head loss in the pipe.
A vertical pipe system shown in the Figure below, d = 300 mm throughout, carries 0.82 (m³/s) of water. Find the pressure drop between A and B if B is 100 m higher than A. Neglect minor losses. Assume f= 0.02, 0.021 and 0.019 for pipes No. (1), (2) and (3) respectivily. I 250 m 550 m 250 m B 11 550 m A 350 m 350 m 550m
Given the following information about a length of pipe: P1 = 440 kPa V1 = 0.0085 m/s z1 = 5 m v2 = 0.8335 m/s z2 = 0 m Head loss from point 1 to 2 = 0.262 m Find the pressure at point 2
Figure Q1 shows an internal piping system of a building. The pipe is uPVC of total length 35 m. The minor loss coefficients are as shown in the figure. The flow velocity in the pipe is designed to be 1.0 m/s and the residual pressure head at appliance X must be at least 0.8m. Determine the required pipe diameter using Darcy Weisbach formula. Level 8.5 m k = 0.8 Water tank IT Roof beam Minor loss coefficients: E Stop valve, k = 10 O 90°elbow, k = 1 Level 4 m Figure Q1
An oil with p=900 kg/m² and v==0.0002 m/s flows upward through an inclined pipe as shown in Fig. E6.4. The pressure and elevation are known at sections 1 and 2, 10 m apart. Assuming d=6 cm 10 m P,= 250,000 Pa 40 P,= 350,000 Pa, z, =0 steady laminar flow, (a) verify that the flow is up, (b) compute h, between I and 2, and compute (c) Q. (d) V, and (e) Re Is the flow really laminar? mpgd'h Q = 128µL 3,431,600 66 10 & Density of Air p = 1.205 kg/m 364 S444 D176= 15 14 0 6 +Go Coefficient of viscosity for air = 1.80 x 10-5 he 151 355m Force of gravity 9.807 Density of waterp 998 kg/m? %3D Coefficient of viscosity (water) u = 0.001 kg/(m.s) For gasoline at 20°C, from the Table p= 680 kg/m³,y = pg, g =9.81
A hydraulic pipeline 3 km long and 50 cm in diameter is used to convey water with a velocity of 1.5 m/s. The pressure rise if the valve provided at the outflow end is closed in 20 seconds is kPa. Consider pipe to be rigid and take bulk modulus of pipe material as, k = 20 x 108 N/m². (round off to nearest integer)
Water flows at a rate of 0.1 m³/s through the horizontal pipe transition as shown below. Pressures at sections 1 and 2 are given. Determine; a) the direction of the flow, b) the head loss, the horizontal force acting on the pipe segment between sections 1 and 2. D₁= 0.1 m P₁= 19620 Pa 2 D₂= 0.2 m P2=49050 Pa
1. The velocity distribution in a 3-cm diameter pipe is given by where ro is the pipe radius. Calculate the shear stress (a) at the centerline, (b) at r = 0.25 cm, and (c) at the wall, if water at 20°C is flowing and umax = 25 m/s. Density Density tap Density Specific Gravity Specific Gravity 4°C reference Density Temp (°C) pure pure pure water water 60°F water (g/em' ) water ( kg/m) (g/cm' ) Ib/cu.ft reference O (solid) 0.9150 915.0 0.915 O liquid) 0.9999 999.9 0.99987 62.42 0.999 1.002 4 1.0000 1000 0.99999 62.42 1.000 1.001 20 0.9982 998.2 0.99823 62.28 0.998 0.999 40 0.9922 992.2 0.99225 61.92 0.992 0.993 60 0.9832 983.2 0.98389 61.39 0.983 0.985 80 0.9718 971.8 0.97487 60.65 0.972 0.973 Water Dynamic and Kinematic Viscosity Temperature Pressure Dynamic viscosity Kinematic viscosity (°C] [MPa] [Pa s], [N s/m2] [eP], [mPa s] lbf s/ft *10) [m'/s*101, (eSt) 0.01 0.000612 0.0017914 1.79140 3.7414 1.7918 10 0.0012 0.0013060 1.30600 2.7276 1.3065 20 0.0023 0.0010016 1.00160 2.0919 1.0035…
Horizontal commercial steel (new) pipe, 150m in diameter, carries 3.5 m^2/sec of water at 20°C. Calculate the pressure change in the pipe per km length = 1.300 x 10^4 m^2/sec and roughness = 0.045 mm for the pipe.
In the figure, friction loss between A and B is neglected while between B and C it is 0.2 (VB²/2g). Find the gauge pressure at C (in kPa) if the water is flowing from A to C at a rate of 304 L/s. Pipes A and C are 443 mm in diameter and Pipe B is 131 mm in diameter. The gauge pressure at A B B is 7.9 kPa.
Compute for the unknown pressure at A. (h1 = 90 cm; h2 = 150 cm; h3 = h4 = 65 cm). Encode your answer with solution using the space provided. SG %3D of saltwater = 1.024 Oil SG = 0.8 h1 h3 h2 A. h4 Salt Water Pa= ? Mercury SG = 13.6
At 20 degree celsius, gage A in the figure reads 295 kPa absolute. The tank is 2m wide perpendicular to the figure. Assume atmospheric pressure to be 1 bar. Sp.gr. of mercury is 13.6. Determine the total pressure acting on side CD in kN. P = 183 kPa abs. show solution and diagram