If the compressor of a Brayton cycle gas turbine operates at apressure ratio 24.9, and the rate of heat transfer during theheat addition process is 590 kW, what is the net work outfrom the device? Take the working fluid to be superheatedsteam with a specific heat ratio of 1.33, and give your answerin kW to one decimal place.

Given data compression ration = 24.9 Rate of heat addition = 590 kW gama = 1.33 work output =?

Answered: vice? Take the working fluid to be…

Engineering

Mechanical Engineering

vice? Take the working fluid to be superheate a specific heat ratio of 1.33, and give your an

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The coefficient of performance (COP) for a vapor compression cycle chiller is 8.7. If the chiller can produce 58 tons of cooling. If the chiller operates for a total of 3568 hours annually, and the cost of electricity is $0.15 per kWh, how much does it cost to operate the chiller? Fill in the operating cost of the chiller in one year in $.
A steam turbine is operated under the conditions shown in the figure.Define:a. steam flow rate (kg/min) to produce 1000 kW powerb. actual steam rate (kg/kWh)!c. turbine efficiencyd. What type of steam turbine belongs to this?
The main purpose of this assignment is for you to think about the 3rd type: the "binary cycle" geothermal power station. It's the design used when the well brings up water that isn't extremely hot, but "regular hot" (generally between 100 and 180 degrees Celsius). Binary cycle is similar to the other two types in one way: after the hot water has transferred its energy, it is recycled by being pumped deep into the ground (study the diagram). What is the name of the part that returns the water to the ground? * Binary Cycle Power Plant Load Turbine Generator Heat exchanger with working fluid Rock layers Production well Injection well
3- A reaction turbine is supplied with steam at (60 bar, 600 C°). The condenser pressure is (0.07 bar). If the reheat factor can be assumed to be (1.04) and the stage efficiency is constant throughout at (80%). Calculate the steam flow required in (ton/hr) for a diagram power of (25 MW). (Ans. 75.6 ton/hr) 4- The steam consumption at full load for a (3 MW) turbine is (16.6 ton/hr). At half load the steam consumption is (9.1 ton/hr). Applying Willan's line, estimate the steam consumption at no load, and the consumption at a load of (2.5 MW). (Ans. 1.6 ton/hr; 14.1 ton/hr)
Air is used as a working substance in a given internal combustion engine, which is supplied with heat at a constant volume. Based on the data, calculate the The work of the cycle.
If the net power output of the cycle is 100 MW, and that the working fluid enters the turbine as saturated steam at P= 8.00 MPa and exist the condenser as saturated liquid at P=8kpa Determine: a) the terminal efficiency (%) b) The mass flow rate of the steam , kg/s C) The rate of heat transfer to the working fluid as it passes through the boiler, KW D) The heat rejected by the working fluid as it passes through the condenser, kW. e) The mass flow rate of the cooling water, kg/s. N.B ( the cooling water enters the condenser at 15°C and leaves at 35°C)
Steam is generated at 4.10 Mpa and 440°C and condensation occurs at 0.105 MPa a. For a Rankine engine operating between these limits, computethe thermal efficiency and the heat rate b. Considering that a Rankine cycle occurs between same limits, determine QA, QR, Wnet and eth c. What mass flow rate is required for a net output of 30 000 kW Don't answer the given problem, just give me the schematic diagram and t-s diagram of the given problem
Fill in the blanks: Determine the efficiency of a constant volume cycle with expansion ratio equal to 7.8. v the "numerical value" No need to
Round everything to four decimal places. When an air conditioner is reversed it can operate as a heat pump. Assume Carnot cycle operation for both.a. If it performs as a refrigerator, with a power input of 23 kW and heat delivered to be3250 kJ/min, what is its COP? Also, if the temperature inside the refrigerator ismaintained at 0°C, what is the surrounding air temperature?b. If it performs as a heat pump, with the same power input and heat delivery as the ref,what would be its COP? If the outside air temperature is 5°C, what would betemperature inside the house?c. If the COP were doubled for the refrigerator and heat pump, what would be thetemperature change in the surroundings for both?
A steam power plant operating on iregenerative cylce includes one feedwater heater [back word]. steam enters the turbine at 4500KPA and 500C and extracted from the turbine at 350KPA. what is thermal efficiency of the cycle ? TTD = 5
3- A reaction turbine is supplied with steam at (60 bar, 600 C°). The condenser pressure is (0.07 bar). If the reheat factor can be assumed to be (1.04) and the stage efficiency is constant throughout at (80%). Calculate the steam flow required in (ton/hr) for a diagram power of (25 MW). (Ans. 75.6 ton/hr) The ctoam ntion at full load for a 12 MWV) turbine ic (1 S 6 ton /brl At balf lead the
1. Figure shows a reheat cycle in which steam is delivered to the high-pressure turbine at 1100 Ibf/in^2, 740 F, and expanded to 200 Ibf/in^2. After the expansion, the steam is warmed to 720 F before being expanded to 1 lbf/in^2 in the low- pressure turbine. Assume the turbines and pump are adiabatic. Compute the high pressure isentropic turbine work. High Q'în Boi ler Condenser Pump Q out 166.8 Btu/lbm 200.1 Btu/lbm 190.2 Btu/lbm 231.1 Btu/lbm 120.5 Btu/lbm