Q3. (a) In Figure Q3 (a), a 27 gram bullet with velocity of 395 m/s is fired to the block inrest condition. Calculate the velocity of bullet and block when the bullet isembedded in the block after the impact.Use your matrix number to get the value of block mass (kg) as in example.Example: If your matrix number is AD190005, use the 4 numbers at the end of yourmatrix number to be the value of block mass. Thus, mass of block is 5 kg.V8 = 395 m/sBulletBlockFigure Q3 (a)

Given: mass of bullet =27 g=0.027 kg velocity of bullet=395 m/s Mass of lock =5 kg To determine:…

Answered: velocity of bullet and block when the…

Engineering

Mechanical Engineering

velocity of bullet and block when the bullet

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use 2D Planar Kinematics methods to solve: A crank (link AB) rotates with an angular velocity of = 4 rad/s as shown. Find the velocity of the slider (piston C) when 0 = 60°. WAN=4 rad/s A 125 mm 300 mm
2. A kilogram mass is attached to the end of the spring with spring constant 2 N/m. Find the equation of motion if the mass is initially released (set in motion) from rest from a point 1 meter above equilibrium position. (Use the convention that displacements measured below the equilibrium position are positive.) (a) Write the initial-value problem which describes the position of the mass. (b) Find the solution to your initial-value problem from part (a). (c) Graph the solution found in (b) on (0
For the Following question Graph all 4 : [I just need all 4 graphs and please explain and make clean solution] Position vs time Velocity vs time Acceleration vs time Force vs time [For your convenience, I have solved the numerical solutions for the problem] (Please Look at the picture since it is much cleaner) Question : A 550 kilogram mass initially at rest acted upon by a force of F(t) = 50et Newtons. What are the acceleration, speed, and displacement of the mass at t = 4 second ? a =(50 e^t)/(550 ) [N/kg] v = ∫_0^t▒(50 e^t )dt/(550 )= v_0 +(50 e^t-50)/550=((e^t- 1))/11 x = ∫_0^t▒(e^t- 1)dt/(11 )= x_0 +(e^t- t - 1)/(11 ) a(4s)=(50*54.6)/550= 4.96[m/s^2 ] v(4s)=((e^4-1))/11= 4.87[m/s] x(4s)=((e^4- 4 - 1))/11= 4.51 [m]
You walk along the beach towards a dock while your friend rows a boat towards the same dock on a flat lake. Your friend's boat approaches the dock on a straight course, but also rotates about its center-of-mass since your friend is not pulling evenly on the oars. If you knew your own velocity (vwalker), the magnitude of boat's angular velocity (thetaboat), and radius vector from yourself to your friend in the boat (rfriend) at any given time, you could use the following equation to calculate the your friend's velocity: vfriend = vwalker + (thetaboat)k x rfriend where k is a unit vector in the vertical direction. True False
A crank-rocker mechanism is to be used to drive a ratchet mechanism. Using mathematics and specific illustrations, find the required crank length in inches required to generate this motion. The swing of the rocker is 35.0 from the vertical position in each direction. (Note: O2 is the crank pivot; O4 is the rocker pivot; C is the coupler-rocker joint; B is the coupler-crank joint). O2O4: 5.6 in.; lies in the horizontal plane O4C: 4.0 in.; mid stroke is vertical
Solve what is asked: A person kicks a ball off a cliff with a velocity of 20 m/s, 30° from the horizontal. It takes 20 seconds to hit the ground, 1. Find the height of the cliff. 2. Find the final vertical velocity of the ball just before it hits the ground. 3. Find the total horizontal range travelled by the ball. 4. Find the magnitude of the final velocity of the ball just before it hits the ground. 5. Find the direction of the final velocity of the ball just before it hits the ground.
Problem 1: Given: g = 9.81 m/s² Radius of the Earth = 6370 km G = 6.67 x 10-11 N-m²/kg² Find: Mass of the Earth Problem 2: Given: The following set of simultaneous equations using matrix inversion. Include Determine: 6X + 7Y+ 18Z = 12 2X + 12Z +9Y = 16 12Y - 7Z+7X = 23 The solution for X, Y and Z using matrix inversion. Problem 3: Given: The same set of equations from problem 2 Determine: The solution for X, Y and Z by hand using Cramer's Rule.
Using the general Lagrange equation, write the model for the elevator shown. Sketch the block simulation diagram.
show step by step working for the following question for the image.
A frame moves along its n-axis a distance of 2 units and is then rotated about the o-axis an angle 60° followed by a rotation about the z-axis by 90°. It was then translated about the a-axis by 2 units and finally rotated about the x-axis by 45°. Construct the transformation matrix equation. Compute the total transformation performed by the frame. Compute the joint variables that had to be made if similar location and orientation were to be created using cylindrical and RPY configuration. The initial point is located at P=[5 3 4]^T
Fill in each of the following blanks with the appropriate word: If the displacement model used in the derivation of the element stiffess matrices is also used to derive the element mass matrices, the resulting mass matrix is called __ mass matrix.
Consider the figure as shown below. O-XoYoZo is the reference frame and O-X₁Y₁Z₁ is the frame attached to the tool. Sketch the tool position after each intermediate position of the operation of the tool about the reference frame: roll π/2(rotate about Zo), pitch -T/2(rotate about Yo), yaw π/2(rotate about Xo). Please write the final rotation matrix expression. ZI,Zo XI,Xo Yı, Yo