Using the cantilever method, calculate for the magnitude of the moment reaction at support A. Express your answer to the nearest whole number, in kN-m. No need to input the sign and units. Just input the numerical value of your answer. В 5m 5m F 100 kN 6m E to

Using the cantilever method, calculate for the magnitude of the moment reaction at support A. Express your answer to the nearest whole number, in kN-m. No need to input the sign and units. Just input the numerical value of your answer. В 5m 5m F 100 kN 6m E to

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Current Attempt in Progress The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw = 16 mm d = 100 mm t = 9.6 mm Additionally: • The area of each pipe is A = 2726 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is Iz=245460000 mm4. If the beam will be subjected to a shear force of V = 275 kN, determine the shear stress at point K, located at yk = 70 mm below the z centroidal axis. H K X Z Ун Ук H ↑ K 31 h
de nangee shape) vwith a spadn of 6 kips/ft. Example 2 The deformation of a simply supported beam, shown in the accompanying figure, is governed by the relationship 7 dy E I. M(x) dr Where M(X) is is the internal bending moment M(x) = M, for all values of x in this problem M, M. O0000KOKO →X а) Derive the equation for the exact deflection. Assume an approximate deflection solution of the form TEX y (x) =A·sin where A = Unknown Coefficient L Use Galerkin Method to evaluate A b) 8
From the figure below, determine reaction Av. Use absolute value. (No need to include sign since absolute values are always positive). *
Force P = 375 N is applied at A as shown. Find the moment about point D. Enter a positive answer if the moment is counterclockwise and a negative answer if the moment is clockwise. Note that the lengths are given in mm but the answer is asked for in N m. 100 mm- -200 mm- 200 mm 25° MD Nm D 125 mm C B
Q2. A steel bar of rectangular cross section is subjected to two equal and opposite couples acting in the vertical plane of symmetry of the bar. Determine the value of the bending moment M that causes the bar to yield. Assume oy=250 МРа. 3 2 3 M' M 3 Note: All dimensions are cm.
Forces F1 and F2 shown in Figure Q4 with its line of action passing through the origin at O. Determine the resultant moment about point P with values as shown in the Figure Q4. Give your answer in vector foIm. All units are in Newtons and meters. Table Q4 shows all values required. Р (-1, -т, п) F1 = ai - bj - ck F, = 180 N FIGURE Q4 TABLE Q4 Force (N) Coordinate Distance (m) a b m n и 110 50 80 10 25 20 15 8
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 430 mm t₁ = 14mm d = 110 mm t = 9.6 mm Additionally: • The area of each pipe is A = 3028 mm². • The moment of inertia of the entire beam cross section about the z centroidal axis is lz= 325870000 mm². If the beam will be subjected to a shear force of V=245 kN, determine the shear stress at point H, located at y = 110 mm above the z centroidal axis. d H.V Answer: TH= x Z MPa Уи YK H K
The bear cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 390 mm tw - 14 mm d = 100 mm t = 4.8 mm Additionally: • The area of each pipe is A = 1436 mm². • The moment of inertia of the entire bear cross section about the z centroidal axis is lz=140920000 mm². If the bearn will be subjected to a shear force of V = 170 kN, determine the shear stress at point H, located at y = 100 mm above the z centroidal axis.
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 470 mm tw = 14 mm d = 120 mm t = 9.6 mm Additionally: • The area of each pipe is A = 3330 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is IZ = 428040000 mm4. If the beam will be subjected to a shear force of V = 215 kN, determine the shear stress at point K, located at yK = 80 mm below the z centroidal axis.
The beam shown in the figure is supported at roller A and pinned at B and has a uniformly distributed loading w 36 kN/m over 1.5 m from the left-hand end and moment loading M = 44 kNm at 1.5 m from end B. - Determine the reaction force at support A. Input your answer as a value only in KN to one decimal place and without +/- sign. w kN/m M kNm B A X -1.5 m -1.5 m -1.5 m-
find all the reactions by slope Deflection Method Im EI = Const 2m A 2m 2 m
A 20-mm-diameter steel rod is 5 points subjected to the axial forces shown. If E = 200 GPa, determine the displacement of end C with respect to the fixed support at A. GOO MM 400 Mm 50KN 40KN A 50KN O - 0.318 mm O - 0.423 mm O - 0.412 mm O - 0.302 mm