Using approximate method, the DC operating parameters of the common emitter BJTamplifier are as follows: VCBQ 9.54 V and Ico 1.265mA with RgBI = 200K Q,RB2-39K Q, Vcc 16 V, a of the Si transistor is 0.996 and ro = infinity.%3D+VccRC1oRB1+ Vo(p-p)+vi10 pFVce(p-p)acinput10 uFRB2RE SC, 100 uFWhich of the following statements is true about the emitter resistance RE?O Use 10KOhms resistor for RE.O Use 1.5KOhms resistor for RE.OUse 2KOhms in series with 56 Ohms resistors for RE.OUse 10KOhms in series with 560 COhms resistors for RE

Answered: Image /qna-images/answer/7752d176-19a1-4668-b15c-bf141f0bb944.jpg

Using approximate method, the DC operating parameters of the common emitter BJT amplifier are as follows: VCBQ 9.54 V and Ico 1.265mA with RgBI = 200K O, RB2-39K 2, Vcc 16 V, a of the Si transistor is 0.996 and ro = infinity. %3D +Vcc RC RB1 1o + Vo(p-p) +vi Vce(p-p) ac input 10 uF RB2 RE S C, 100 uF Which of the following statements is true about the emitter resistance RE? O Use 10KOhms resistor for RE. O Use 1.5KOhms resistor for RE. O Use 2KOhms in series with 56 Ohmns resistors for RE OUse 10KOhms in series with 560 Chms resistors for RE.

Using approximate method, the DC operating parameters of the common emitter BJT amplifier are as follows: VCBQ 9.54 V and Ico 1.265mA with RgBI = 200K O, RB2-39K 2, Vcc 16 V, a of the Si transistor is 0.996 and ro = infinity. %3D +Vcc RC RB1 1o + Vo(p-p) +vi Vce(p-p) ac input 10 uF RB2 RE S C, 100 uF Which of the following statements is true about the emitter resistance RE? O Use 10KOhms resistor for RE. O Use 1.5KOhms resistor for RE. O Use 2KOhms in series with 56 Ohmns resistors for RE OUse 10KOhms in series with 560 Chms resistors for RE.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

04:- Design a bias circuit for NPN silicon transistor having a nominal B-100 to be used in voltage divider circuit with Q-point of Ic 10 mA and VCE = 10 V. Use standard valued 5% resistors and draw a schematic diagram of your design. (10 points)
A certain npn silicon transistor has vBE=0.7 V for iB=0.1 mA at a temperature of 30°C. Sketch the input characteristic to scale at 30°C. What is the approximate value of vBE for iB = 0.1 mA at 180°C? (Use the rule of thumb that vBE is reduced in magnitude by 2 mV per degree increase in temperature.) Sketch the input characteristic to scale at 180°C.
Design the following MOSFET circuit for it to operate in saturation mode with 0.5 mA drain current. Determine Rp and dc voltage VĎ. Assume V₁ = 2 V and K = 0.1 mA/V² for this MOSFET. 10 V RD -VD
A 4.7 zener diode is connected to the base resistor. The left side of the resistor sits at about 12V. The right side of the biasing resistor is connected to the Zener and npn transistor. The Zener bias is 5mA. The base current needed is 80uA. What is the appropriate resistor for this circuit? (In kohms) I
In a properly Biased NPN transistor most of the electrons from the emitter A. recombine with holes in the base, B. recombine in the emitter its self, C. pass through the base to the collector, D. are stopped by the junction barrier. In transistor, the relation among emitter current, base current and Collector Current is: A. Ic=IB+IE, B. Ig=IB+Ic, C. IE=Ic-IB, D. I=Ig-Ic. • Transistor is known as bipolar transistor because it has: A. Electrons, В. Holes, C. Electrons and holes, D. None of the above. In NPN or PNP transistor: A. Ic> IE, B. IE >Ic, C. IE = Ic, D. None of the above. The base of an NPN transistor is: A. Heavily doped, B. Lightly doped, C. Medium Doped, D. Doped by pentavalent material. In a transistor the value of a (B) is 100, the value of (a) is: A. 0.01, В. О.1, C. 0.99, D.1.
The arrow on the symbol of MOSFET indicates O a. that it is a N-channel MOSFET O b. that it is a P-channel MOSFET Oc. the direction of electrons O d. the direction of conventional current flow
Solve for (IC) collector current in milli ampere and (VC)dc collector voltage in volts
A transistor current is given below. The Zener diode breakdown voltage is 5.3V as shown. Take base to emitter voltage drop to be 0.6V. The value of the current gain ß is ..... 4.7kQ2 0.5mA ↓ 5.3V www 41 + 0.6- www 22092 47092
The mode of operation for the D-MOSFET is Select one: a. the ohmic region only b. the enhancement mode only c. both the depletion and enhancement modes d. the depletion mode only
There are three different main semiconductor devices of FETs which are JFET, D-MOSFET, and E-MOSFET. All of them are also known as active semiconductor devices. i) Briefly explain the different between JFET and D-MOSFET. ii) Given that Vp = - 6 V and IDSS = 10 mA. Draw the transfer characteristics of n-channel JFET using shorthand method. iii) State the general relationship of JFET, D-MOSFET, and E-MOSFET.
Question: 8. With the emitter bias shown, a reasonable assumption for troubleshooting work is that the VcC a. base voltage =+1 V +15 V b. emitter voltage = +5 V RC 3.9 k2 c. emitter voltage =-1 V d. collector voltage = Vcc RB 68 kQ %3D RE 7.5 kQ VEE -15 V
RL 4. Suppose one NPN transistor is working under activation region, and Ip=0.005A. 12 What's the value of Ic given B=100. What's the value of I-? Vcc VE