Use the information in Fig. 6.80 to calculate: a. The source voltage E. b. The resistance R2. c. The current 11. d. The source current Is. e. The power supplied by the source. f. The power supplied to the resistors R1 and R2. g. Compare the power calculated in part (e) to the sum of the power delivered to all the resistors. E + Is 14 · 12 Ω 3 A R₂ R3 P = 120 W 6Ω

Use the information in Fig. 6.80 to calculate: a. The source voltage E. b. The resistance R2. c. The current 11. d. The source current Is. e. The power supplied by the source. f. The power supplied to the resistors R1 and R2. g. Compare the power calculated in part (e) to the sum of the power delivered to all the resistors. E + Is 14 · 12 Ω 3 A R₂ R3 P = 120 W 6Ω

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

b) Describe component X 6.0V heator i. The heater is designed to work from a 3.6 V supply. It has a power rating of 4.5 W at this voltage. By considering the current in the heater, calculate the resistance of component X when there is the correct potential difference across the heater.
1. Create 10 Ohm's Law Problems of YOUR OWN. Solve and write your solution and don't forget to draw the figure.
A 75-V DC voltage source is coupled to a 25 kOhm load resistor through a 35 kOhm source resistance. A Voltmeter-A has a sensitivity 8 kOhm/V with a measuring range of 0-35V. Calculate error in the voltmeter reading expressed in a percentage of the true value.
An aluminum wire 5m long and 2mm diameter is connected in parallel with a copper wire 3m long. The total current is 4 A and that in the aluminum wire is 2.5 A. Find the diametre of the copper wire. The resistivity of copper wire being 1.7 micro ohm meter and that of aluminum taken Al 2.6 micro ohm meter
Two voltmeter of (0-300 V) range are connected in parallel to a A.C. circuit. One voltmeter is moving iron type reads 200 V. If the other is PMMC instrument, its reading will be a)200 V b) slightly less than 200 V c) 0 V
Please let me give solution
Suppose a 10.0 ohm resistor is connected to an emf source to make a closed circuit. If the source has emf = 15.0 V with an internal resistance r = 0.5 ohms, which of the following correctly compares the voltage drop across the emf source and the attached resistor? O a. Voltage drop across emf source is directly proportional to the external resistor O b. Voltage drop across emf source is greater than external resistor O c. Voltage drop across emf source is less than external resistor O d. Voltage drop is the same for the emf source and the external resistor O e. None of the above
1. The no-load terminal voltage of a battery is 30 V. The terminal voltage drops to 22 V when supplying a current of 5 A. Determine the emf and the internal resistance of this battery. 2. Two identical zinc carbon batteries are available. When connected in series, they supply 0.5 A to a 4 ohm resistor. When connected in parallel, they supply 0.4 A to a 5 ohm resistor. Determine the emf and internal resistance of each battery. 3. When supplying a current of 5 A, the terminal voltage of a battery is 15 V. The battery is then recharged at a rate of 3 A and the terminal voltage is found to be 21 V. Determine the emf and the internal resistance of the battery. 4. A battery with an emf of 12 V and an internal resistance of 0.8 ohm is to be recharged through a 20 V source. (a) show by means of a diagram the connection of the circuit elements. (b) What is the current in the circuit? (c) The recharging current is to be limited to 3 A. What is the value of the limiting…
You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
docs.google.com 8 1. What are the values of the resistances bellow according to these colors? a. Orange – blue - green - gold b. Violet – yellow – violet – silver c. Yellow – gray - green - orange - gold d. Blue - brown- red- orange - gold – red 1 Add file 2. How can you connect Avometer to measure current, voltage and resistance? * Your answer 3- how can you examine the capacitor and diode if they work or not ? *
6. a. The potential difference across the terminals of a battery is 8.5 V when there is a current of 3000 mA in the battery from negative to positive terminal. When the current is 2000 mA in the reverse direction, the potential difference becomes 11 V. What is the internal resistance of the battery? What is the emf of the battery?
2. Determine the equivalent resistance between the terminals a and b 452 352 C0.6662 0.61 0.33352 bo