U.S. Sieve No.Percent finer than2010080961708520080Hydrometer 0.04 mm0.02 mm59390.01 mm260.005 mm0.0015 mm158. a.Determine the percent of finer than each sieve and plot a grain size distributioncurve.b.Determine D10, D30, and Deo from the grain size distribution curve.Calculate the uniformity coefficient, C.Calculate the coefficient of gradation, Ce.C.d.

Answered: U.S. Sieve No. Percent finer than 20…

U.S. Sieve No. Percent finer than 20 100 80 96 170 85 200 80 Hydrometer 0.04 mm 0.02 mm 59 39 0.01 mm 26 0.005 mm 0.0015 mm 15 8.

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter4: Mechanical Processes

Section: Chapter Questions

Problem 4.9P

See similar textbooks

Related questions

Q: 1. Complete the given table Sieve number Diameter(mm) Mass retained Cumulative Mass Percent Passing…

Q: Determine the uniformity coefficient and coefficient of gradation from the following data: Sieve No.…

A: In order to determine the uniformity coefficient and coefficient of gradation, first we need to plot…

Q: The following data is the result in performing the ASTM C128, Determine the Bulk Specific Gravity,…

A: M1 = Mass of pycnometer = 250 M2 = Mass of pycnometer + Mass of oven dry sample = 250+895 = 1145 M3…

Q: What is the moisture content for test 1? Round off your answer to two decimal places. No need to…

Q: The water temperature is 14°C and the mean pore diameter is 0.33 mm. Is it permissible to use…

A: Find velocityv=Knedhdlv=12ftday0.170.0055=0.388ftd

Q: Look for the meaning and the corresponding formula for each the following propertie Use engineering…

A: Given :- a soil with three phase condition.

Q: Following are the results of a sieve analysis: U.S Sieve No. Diameter (mm) Mass Retained (grams)…

Q: the surface area becomes 12.57 mm². By Using the following graphs, find the tensile strength and…

A: The given data is: Ao=Original surface area=20.25 mm2 A=Final surface area=12.57 mm2

Q: Question #6: In a water sample, the following elements are detected. Calculate the total hardness,…

Q: A weather report indicates the barometric pressure is 28.54 inches of mercury. What is the…

A: Given: The barometric pressure P is 2854 inches of mercury. Calculation: Convert the given…

Q: Define bulk modulus and write its dimensions. In hydraulic applications is water considered a…

A: Bulk modulus is defined as a measure of resistance of fluid to compression. Actually the…

Q: | 180 mm Y (mm) 50 + B (mm) х-ахis 250 mm

Q: 3. A 30 m steel tape is 2 mm too long at 20°C with a pull of 55 N. A rectangle is measured with this…

A: Answers are Actual length of Tape = 30.005480m, True Area = 16385.33 m2, Error in Area = 5.98 m2.…

Q: Part A Determine the mass moment of inertia of the thin plate about an axis perpendicular to the…

Q: Cumulative Percentage retained Sieve Sieve mass Cumulative % No. size(mm) retained (g) cumulative %…

A: Given Cumulative Percentage Passing Sieve size To Create soil distribution curve in excel.

Q: results shown in the Table below, Calculate the percent passing through each sieve. Plot percent…

A: Calculate the percentage of soil retained over each sieve, % retained = Weight of soil…

Q: Problem In a specific gravity test, the following data were recorded. Mass of pycnometer jar Mass of…

A: solution Given mass of pychonometer jar M1=530gmass of pychonometer with clean water M2=1560gmass of…

Q: 3. What is the magnitude of the coefficient of viscosity? a) Frictional force/Area b) Frictional…

Q: A sample of a dry coarse grained material of 500 grams was shaken through a nest of sieves and the…

A: Uniformity Coefficient (Cu): It is defined as the ratio of D60 to D10. Cu= D60D10 D60= Particle size…

Q: PROBLEM 7: Locate the center of mass of the block in millimeters. Materials 1, 2 and 3 have…

Q: 1. Copy and complete the table below (show in your solution paper) and input the Percentage Passing…

Q: Which length shall I use to calculate current density: the whole bar length or the embedded length…

A: Answer embedded length is known as the length of the embedded steel reinforcement, The embedded…

Q: What is the moisture content for test 1? Round off your answer to two decimal places. No need to…

A: To find the moisture content-

Q: 5. Calculate: i) apparent specific gravity ii) bulk specific gravity iii) apparent particle density…

A: A=mass of oven dry sample=480gB=mass of pycnometer filled with water=1400gC=mass of pycnometer…

Q: Determine the mass moment of inertia of a steel shaft that is 1 m long and has a diameter of 5 cm.…

A: The given data is shown below:

Q: Define, derive, and give (2) examples on each model. 1. Horton Model and Philip’s equation 2.…

A: Horton Model: Horton's Model is named after Robert E. Horton. Hortons's Model is used to measure the…

Q: 5. What is the default value of pipe length? a) 5 meters b) 20 meters C) 10 meters

A: This question is related to the Pipe Network from Fluid Mechanics. In this question we answered…

Q: Civil Engineering help Table 1 Test No. Avg. sample length (mm) Rate of Avg. sample diameter (mm)…

A: What to determine was not mentioned clearly, please provide the full question. I just circled the…

Q: SIEVE NO AMOUNT RETAINED (g) 4 33 8 42 10 14 30 164 40 73 100 159 200 20 PAN 31

Q: 1-15. Water has a density of 1.94 slug/ft'. What is the density expressed in SI units? Express the…

A: Given data in question Water Density is 1.94 slug/ft3 To find out SI unit of density Value in SI…

Q: Given beloW is the result of a sieve analysis done on Sieve No. Diameter Percent Passing % 4 4.750…

Q: Referring to the dial gauge shown in Figure , determinea. Accuracyb. Sensitivityc. Range, given that…

A: Given: Consider the dial gauge shown in the below figure,

Q: RA= RB= Vmax= KN 2 decimal places KN 2 decimal places KN 2 decimal places

Q: Consider a large cubic ice block floating in seawater. The specific gravities of ice and seawater…

Q: Complete the table if the oven dried mass is 161.42 grams. Make sure you show your solutions and…

Q: A rectangular plate of aluminum with a specific gravity of 2.7 is floating between a mercury-water…

Q: Q.1 Calculate Reynold’s Number if kinematic viscosity of a liquid is 0.001 m2/s , density is 500…

A: ν=0.001m2/s ρ=500 kg/m3 d=10mm velocity=30m/s Reynolds Number=500x30x(10/1000).5Reynolds Number=300

Q: 3. What is the relationship between Orificemeter diameter and pipe diameter a) Orificemeter diameter…

A: Brief concept- Orifice meter- It is the most common method for calculating the flow rate in a pipe.…

Q: he viscosity of a certain fluid is 4 x 104 poise. Determine its viscosity in both (a) SI and (b) BG…

Q: 9. What is D'Alembert's Paradox? a) Resistance= 0 b) Drag force= 0 c) Temperature = 0 d) Pressure…

A: Brief concept- D'Alembert's paradox- Jean le Rond d'Alembert, a French mathematician, discovered…

Q: PROBLEM 1: Reynold's number is used to determine the type of flow pattern through a pipe. It is…

A: Given V= 9.84 ft/sec Density= 1.79 slugs /ft3

Q: Sieve Percent Sieve opening passing (finer) 100.0 100 No. 90 (mm) 80 3" 75 3 70 * 60 4 4.75 80.1 10…

A: The amount of soil retained on a particular sieve= 100- percentage finerof that sieve.

Q: Convert 2500 inches /hour to feet/ min

Q: Describe Effects of Groundwater and Freezing.

A: Effect of water table on bearing capacity:

Q: Part 1 weigh of the graduated cylinder (gr) minuscus level (mL) weigh of the cylinder+water (gr)…

A: wt of the graduated cylinder in gms (w) 85 meniscus level ml (v) 90 wt of cylinder +water in gms…

Q: 5. Find the total surface area of the given figure below. If L = 13ft, Y = 5ft, X = 9ft E 60° Your…

Q: sieve anlysis results effective diameters floor # 4 #10 # 40 # 200 D10 D30 D60 LL PL 1 98 86 66 56…

A: soil classification according to AASHTO and USCS both are based on the plasticity of soil. on the…

Q: (b) Calculate the quantity of lime and soda required for softening one million litre of the…

A: Given: Purity of lime and soda are 80% and 85% Impurities are Silica-75 mg/lit…

Q: 1. (8 points) Calculate the value and fill into the blanks. Given condition is as follows: Va air Vw…

A: solution Given Volume of air =VaVolume of water Vw=4VaVolume of the solids Vs=Vw+Va=4Va+Va=5Valet…

Concept explainers

Pressure and Stress

Question

100%

U.S. Sieve No.
Percent finer than
20
100
80
96
170
85
200
80
Hydrometer 0.04 mm
0.02 mm
59
39
0.01 mm
26
0.005 mm
0.0015 mm
15
8.

a.
Determine the percent of finer than each sieve and plot a grain size distribution
curve.
b.
Determine D10, D30, and Deo from the grain size distribution curve.
Calculate the uniformity coefficient, C.
Calculate the coefficient of gradation, Ce.
C.
d.

Expert Solution

Step 1

Given data:

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Nedd solution
If you could help me with parts a-d id greatly appreciate it, I will rate immediately. Thank you.
Calculate the sieve analysis shown in Table P5.20, and plot on a 0.45 power gra- dation chart. What is the maximum size? What is the nominal maximum size? TABLE P5.20 Cumulative Amount Sieve Size, Amount Cumulative Percent Percent mm Retained, g Retained, g Retained Passing 37.5 25 315 19 782 9.5 1493 4.75 677 0.60 1046 0.075 1502 Pan 45
Use IS code for analysis
5.20 Calculate the sieve analysis shown in Table P5.20, and plot on a 0.45 power gra- dation chart. What is the maximum size? What is the nominal maximum size? TABLE P5.20 Sieve Size 37.5 mm 25 mm 19 mm 9.5 mm 4.75 mm 0.60 mm 0.075 mm Pan Amount Retained, g 0 315 782 1493 677 1046 1502 45 Cumulative Amount Retained, g Cumulative Percent Percent Passing Retained
Largest grain size for no. 100 sieve
F1 = 603 N F2 = 818 N Show a clean and organized solution please
USE NCSP 2015
The following plot belongs to a concrete slab and is intended to determine the formwork removal time. Formworks are planned to be removed when 60% of maturity of the laboratory samples cured at 20 °C for 7 days is reached. Determine the formwork removal time (in days) if the datum temperature is -5°C. 25 Temperature (°C) 20 15 10 5 01 2 3 4 5 6 7 8 Age (days) 9 10 11 12 13 14
Q3) The result of sieve analysis of a sample of aggregate given in the Table below. According to ASTM C 33, the sample is acceptable or not? BS Total mass of sample 4 80 g Sieve size 10 mm 5 mm 2.36 mm 1.18 mm 600 μm 300 μm 150 μm €150μm ASTM in 4 8 16 30 50 100 <-100 Mass retained O 80 40 80 110 68 61
The following are the results in the test for specific gravity of fine aggregates:Mass of Oven-dried specimen in air = 502gMass of Pycnometer filled with water, to calibration mark = 640gMass of Saturated Surface Dry Specimen = 510gMass of Pycnometer filled with specimen and water to calibration mark = 950gCalculate the absorption, apparent specific gravity, bulk specific gravity in SSD condition, and bulk specific gravity in OD condition
Make a good quality solution