Mechanics Two couple forces and one moment act on the pipe assembly shown below.Find:(1) MRijk, the resultant couple moment in {i.j.k} formatAn example of (i.j.k} form is: 22.4i-11.3j-70.3kF,kC(-2,4,2H)A (0,0,H)FajD (-3,5,1.5H)-FajВ (0,3, Н)O (0,0,0)-F,kAnswer all numeric solutions with five significant figures.H = 3 mF1 = 168 NF2 = 183 NM = -164 N-m

Answered: Two couple forces and one moment act on…

Two couple forces and one moment act on the pipe assembly shown below. Find: (1) MRijk, the resultant couple moment in (i.j.k} format An example of {i.j.k} form is: 22.4i-11.3j-70.3k

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: open channel having a slope of 0.0065 is used to carry 1 cubic meter per second of water., Find the...

Q: a

Q: Determine the reaction/s at supports A and D if P1 = 28 lb, P2 = 98 Ib and x = 13 ft. What is the va...

Q: Determine the force in member EF for the truss shown using the method of joints. 40 kN 40 kN 40 kN -...

Q: For a simply supported prestressed concrete bearn, compute the stress in the bottom fiber at midspan...

Q: Calculate the distance of neutral axis (in cm) from top in an RC trapezoidal section which has a top...

Q: A 0.5 kg mass is projected up a long 25° inclined plane with an initial speed of 4.5 m/sec. The bloc...

Q: roof truss shown using method of joints. Specify whether the forces in each member are in tension or...

Q: For the simply supported beam shown below, determine the internal resultant loadings at a point 0.5 ...

Q: n. Determine the normal stress in the rod at

Q: 2 m 1 m 25KN

A: To find out the shear for at T.

Q: SITUATION: An open cylindrical vessel 1.3 m in diameter and 2.1 m high is 2/3 full of water. If rota...

Q: A 50 mm diameter siphon draws oil (S.G. = 0.82) from a reservoir. If the head loss from point 1 to p...

Q: The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made ...

Q: Problem 1: Find AAAR in the following structure. 2F F F Rigid

A: Given Data -

Q: A bronze pipe (1) is to be connected to an aluminum alloy pipe (2) at flange B. When put in place, h...

Q: Determine the error in distance if the uppermost portion of a 3m long stadia rod is inclined 15cm t...

A: Given Rod intercept = 1.65 m Inclination = 15 cm = 0.15 m To Find Error in distance

Q: (a) the normal stress in the polymer cylinder. (b) the normal strain in the polymer cylinder. (c) th...

A: ###Determination of Normal Stress and Strain ###

Q: If a certain gasoline weighs 20 lb/ft3, what are the values of its density, specific volume, and spe...

Q: 500KN 200mm 100mm What is the value of force P in KN?

Q: The steel plate shown below is put in into a rigid chamber, such that spacings of size s- 0.003 m. T...

A: To Determine Increase in temperature along x-axis to just close the spacing on the right in degree c...

Q: *2-12. The component of force F acting along line aa is required to be 30 lb. Determine the magnitud...

A: Given -

Q: SITUATION: A footing, 2m x 3m in plan and 0.50m thick, is designed to support a 0.60m square column....

A: Given data: Footing dimensions = 2 m x 3 m Square column dimensions = 0.6 m x 0.6 m Load on the colu...

Q: A pin and two rollers support bars ABC and CD. A hinge at C connects the bars. The distributed loadi...

A: Given Data -

Q: 2. The lap joint that is 130 mm wide and 25 mm thick is connected by three 20-mm-diameter rivets. As...

A: Given, d=20 mm Number of rivet n=3 Allowable shear stress = 65 MPa Bearing stress =45 MPa Maximum te...

Q: The solid 1.05-in.-diameter rod is subjected to a uniform axial distributed loading along its length...

A: Determine normal stress at x=8inch and x=24inch

Q: 4. A closed traverse has the following data: Line Departure 37.39 Latitude DPD 2A АВ 1455.23 ВС 19.1...

Q: The solid steel rod (1) shown in the figure has an allowable shear stress of 3 ksi. The brass tube (...

Q: A 50 m diameter solid metal bar is subjected to a compressive load of 178 kN. Transverse and longitu...

Q: plymer cylinder (2) is clamped between rigid heads by two steel bolts (1). The steel [E 29,000 ksi; ...

Q: A finite slope has a height of 9m and it makes an angle of 30 degrees with the horizontal. The unit ...

A: To Determine The developed frictional force along the failure plane.

Q: The composite shaft shown in the figure consists of a bronze sleeve (1) securely bonded to an inner ...

Q: For sleeper density of (n+ 6), the number of sleeper required for constructing a BG track of length ...

Q: What is the significance of architecture?

A: Architecture: The study of buildings and various techniques required for the construction of buildin...

Q: 1. Compute the acceleration of body B, and the tension in each cable supporting each block. WA= 200 ...

Q: A cantilevered portico slab is 5 m in width and is having 2 m effective span. Assuming moderate envi...

Q: A polymer cylinder (2) is clamped between rigid heads by two steel bolts (1). The steel [E = 29,000 ...

A: To determine: normal stress in the polymer cylinder normal strain in the polymer cylinder normal st...

Q: Velocity profiles are measured at the upstream end and at the downstream end of a control volume as ...

A: given data v=vmax.=3 m/s ρ=1.22 kg/m3H=1m we have to calculate the drag per unit length on the wa...

Q: 90 KN 100 80 KN m AN m m 6 m-

Q: 6m ugiz

Q: The influence line for the vertical reaction at C for the beam shown is B 7 m- 7 m 4 m-

Q: 4. Find the tension T, in the rope shown in figure. А. 83.2 N B. 45.8 N C. 70.7 N D. 50 N 45° T2 B 5...

Q: The solid 1.55-in.-diameter rod is subjected to a uniform axial distributed loading along its length...

Q: A shaft subjected to torsion experiences a pure shear stress on the surface. The maximum principal s...

Q: Problem 1: Find AA/ar in the following structure. 2F F F Rigid В

A: Calculate the ratio of ∆A∆B in the given structure, Now apply the slope deflection method , ∆A=∫0LM1...

Q: A solid circular bronze [G = 6,500 ksi] shaft, 5.8 ft long and 1.275 in. in diameter, carries a torq...

Q: An unlined channel in alluvial soil has a seepage loss of 2.5 cumecs/ million sq.m of wetted perimet...

Q: For the beam and loads shown, select stirrup spacings if f'.= 4000psi, normal-weight concrete and fo...

A: Support reaction: Ay=By=48+1.8×242=45.6 K Vu=Ay=By=45.6 KVuc=Vu-1.8×d=45.6-1.8×32.512=40.5725 Kps

Q: Problem 1 The cantilevered rectangular bar is subjected to a force of 9 kips. a. Determine the major...

Q: *2–12. The component of force F acting along line aa is required to be 30 lb. Determine the magnitud...

Concept explainers

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.

Question

Mechanics

Two couple forces and one moment act on the pipe assembly shown below.
Find:
(1) MRijk, the resultant couple moment in {i.j.k} format
An example of (i.j.k} form is: 22.4i-11.3j-70.3k
F,k
C(-2,4,2H)
A (0,0,H)
Faj
D (-3,5,1.5H)
-Faj
В (0,3, Н)
O (0,0,0)
-F,k
Answer all numeric solutions with five significant figures.
H = 3 m
F1 = 168 N
F2 = 183 N
M = -164 N-m

Branch of science that deals with the stationary and moving bodies under the influence of forces.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

for the beam shown in the figure, a) find the equation of elastic curve by integration method. b-) Draw (Ty), (mx) oliagrams of the beam. c-) find the Suppert reactions. 29=260 9=130 9-130 E L-158cm Figure: L=158 cm
A force-couple system is acting on the frame as shown. Use A=80N, B=700N, C=150N, and M= 120N.m. The system is to be replaced with a single resultant force R. B 30° [Select] [Select] [Select] [Select] [Select] [Select] M 400 mm 200 mm 300 mm (a) Calculate the absolute value of the x-component of the resultant in N. (b) Calculate the absolute value of the y-component of the resultant in N. (c) Calculate the magnitude of resultant in N. (d) Calculate the angle that the resultant makes with the horizontal in degrees. (e) Calculate the absolute value of the x-intercept of the resultant's line of action in mm. (f) Calculate the absolute value of the y-intercept of the resultant's line of action in mm.
Q2-B- Fill in the blank with the correct answer. 1. When the resultant of force system acting on a body is zero, the body is said to be in (a) rotating condition (b) translation condition (c) equilibrium condition 2. Number of component of reaction at hinge support are (a) zero (b) one (c) two (d) three 3. The angle that the vector A-2i+3j makes with y-axis is 4. If angle made by the force with y and z axes are 8, = 60° and 9, = 45° then 0,= 5. Force is completely defined by its (a) magnitude (b) direction (c) point of application (d) All of these (d) dynamic condition
The steel pipe (G - 75GPA) has an outer diameter of 50mm and an inner diameter of 30mm. It is fixed at A and three torques are applied to it as shown. Solve the rotation of the free end with respect to the fixed end. 200mm 250mm 300mm 30 N-m 20 N.m 80 N-m O 0.000749rad O 0.000674rad O 0.00624rad O 0.00142rad
The homogeneous wire ABC is bent into a semicircular arc and a straight section as shown and is attached to a hinge at A. Determine the value of e (in degrees) for which the wire is in equilibrium for the indicated position. B C Numeric Response
RBH TRBV 3. The frame shown in the figure is hinged to rigid supports at A and E. find the components of the hinge forces at A and E and the forces in members BC and BD. RAH A REH TRAV E REV 120 D 5 0 ction
Q3. The truss shown below is fastened to E using a fastening strap. If the strap is to be considered as a support reaction, find the force in the strap. Next, determine the reactions at the other supports and forces in all members of the truss. The cross-sectional area of each member is as indicated. Use the value of E-210 kN/mm². A E (1000) 4m (800) (009) B (1000) (008) 3m D 100 KN 2m 4m FIGURE 03
An I-section beam ABC has a constant El and is loaded as shown in the figure below. This beam has a fixed support at the right while the left support is a guided roller. For the given beam and loading conditions, provide and determine the following: A +y nashadyolingras +x L/2 expression. D. Boundary som 9. The moment reaction at A. B noding (0) wL² L/2 gramat D. The constants of integration C1 and C2. E. The moment reaction at C. F. The vertical force reaction at C. G. The deflection at point A in terms of w, L, and El. c
CALCLULATE THE FEM OF THE FOLLOWING USING THREE MOMENT EQUATION.
Eiample ai ABC is loaded via a 500 N.m couple and a 600 N force as shown. Tlie The is connected to the rest of the system by a pin joint at B and a roller support at Beteune the magnitide of the reaction forces on the beam at the supports. 600 N 300 N m 400 300 500 Ans. Dimensions in mm RC=1700 N 20 RBx=1597.5 N RBy=1181.4 N Erample Determine the force Pnecded to lift the load. Alsa, determine the proper placement x of the hook for cotilibrium. Neglect the weight of the beam. 0.9 m 100 mm 100 mm 100 mm 6 kN The uniform rod of length L and weight W is supported on the simooth planes. Determine its position e for equilibrium. Neglect the thickness of the rod. Ans 6= tan
EXAMPLE 4.7 Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. For the loading shown and knowing that E.= 200 GPa and E.= 105 GPa, determine (a) the reactions at A and E, (b) the deflection of point C. Dimensions in mm 100 100 -180-- Dl E Steel Be 60 kN Brassc 40 kN 40-mm diam. 30-mm diam.
for the beam shown in the figure, a) find the equation of elastic curve by integration method. b-) Draw (Ty), (mx) oliagrams of the beam. c-) find the suppert reactions. 9=9&N/m 9-9 N/m J L=180cm L=180 cm Figure: