top width, how much additional land space (in ft2) will be needed for the base of the levee per mile of levee length? Assume side slopes remain 3:1. Show all your work

Q: A simply supported beam, 6m in length, has an initial deflection of 0.50mm at midspan due to its own...

A: Given That  L= 6m Δmax=0.5mm =0.0005m Let us assume the own weight is "w"  kN/m E = 24870MPa I = 540...

Q: Draw the internal axial force diagram (AFD), shear force diagram (SFD), and bending moment diagram (...

A:

Q: A new 50 km freeway was required to constructed between two cl design speed 70 mph, the expected 20 ...

A: Given, Design speed= 70 mph DVH=12000 vph PHF=0.95 FHV=0.85C=2000 pc/hrDirectional split =65% Cost p...

Q: Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN...

A: Using equilibrium and compatibility establish the equation of equilibrium and solve them to get the ...

Q: A force of FA=460 N is exerted on lever AB as shown. The end B is connected to a piston which fits i...

A: Draw the FBD of the given Lever system. Calculate the pressure at C. The same pressure will act at p...

Q: The moisture content of a soil sample is 18.4%, and its dry unit weight is 100 lb/ft3. Assuming that...

A: The moisture content of a soil sample, w=18.4dry unit weight, γd=100 lb/ft3G=2.65

Q: whereas the flexural rigidity of the secO

A: P0LAE=60-RaK0 AE =0 AB = PLEAAE =AB+B+CD+DE

Q: Discuss three ways to remove water from the air in an air distribution system.

A: Explanation- Although it is hard to completely eliminate moisture from your air compressors, you can...

Q: Express the repeating decimal as a fraction. 2.191919...

A:

Q: A sample of coarse sand was found to have a void ratio of 0.87 and 0.52 in its loosest and densest s...

A:

Q: Draw a fish-bone chart detai ling reasons why an airline customer might be dissatisfied.

A: The fish bone chart is given as:- A - MaterialB - MachineC - MethodD - Manpower I - Not enough parki...

Q: The frame shown is supported by a shear pin (diameter, d, ultimate shear Tu in ksi) and by a tie-rod...

A:

Q: Determine the Azimuth ED reckoned from North in Clockwise Direction. Note that the clockwise rotatio...

A:

Q: (Problem 4.16 from the text book) The beam shown is made of a nylon for which the allowable stress i...

A: We will find neutral axis and permissible stresses.

Q: Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN...

A:

Q: The horizontal distance between two points, A and B is 420m, and these are established along the sam...

A:

Q: The round bar shown in the figure has steel, brass and aluminum sections. Axial loads are applied at...

A: Draw the FBD of each section such that each part is in equilibrium. Then using the definition of str...

Q: Can you Write a note on Balking, Reneging & Jockeying in Queuing System?

A: Brief concept- Queuing System- A line system is a system with a service area where different types o...

Q: should the total evaporable mosture and total surface moisture should be equal? what will happen to ...

A:

Q: What is the relevance of geology in Geotechnical Engineering? (Minimum of 7 sentences)

A:

Q: Describe the function of an air filter

A: Function of air filter

Q: Please help, I will give a good feedback. Short and simple answers are accepted as long as it is not...

A:

Q: Problem: The beam has a given cross section as shown. fc = 7.8 MPa, fs = 152 MPa, n = 12. Determine ...

A:

Q: On a simple curve, the perpendicular offset distance from point A to Q on the tangent line is 60 met...

A:  ANSWER :-The length of long chord is 1043.37 m

Q: Att = Os, an experimental electric powered car starts from rest at point A and moves toward the righ...

A:

Q: Two circular shafts are joined together between fixed supports to resist a orsional moment of 80 kN-...

A:

Q: State three conditions which lead to very low water application efficiency in most lowland rice farm...

A: Water applications effeciency = (Water actually stored in root zone /water delivered to field) × 100...

Q: Sieve analysis on a dry sample of mass 1000g showed that 980 g and 270 g of soil pass through the 4....

A: Given Total mass of soil = 1000 g Mass of soil passing through  Sieve 4.75 mm = 980 g Seive 0.075 mm...

Q: Which of the following nearly gives the %gravel of Soil B using AASHTO? which of the following give...

A:

Q: A 3 layered density tower includes 30 cm glycerin (D = 1260 kg/m3), 25 cm oil (D = 950 kg/m3), and 2...

A: Given:- The thickness of glycerin layer = 30 cm = 0.30 m  The density of the glycerin = 1260 kg/m3  ...

Q: According to ASTM, when a microwave oven is used for drying of samples, the container shall be A met...

A: Answer :     option ( C )  non metallic.    is correct More explanation is given below.

Q: B 10 m 10 m 10 m

A:

Q: Why the velocity at the vane (V) is less than at the exit of nozzle (Vo)?

A: The impact of a water jet is studied to measure to the force exrted by the jet on flat, inclined or ...

Q: Problem 3 For the given beam shown. Calculate the following. Use El=45x10² kN-m². 2 kN 2 kN w = 5 kN...

A:

Q: The posted speed along Daang Maharlika Highway is 60 km/tr. The Table below shows the summary of 15o...

A: As per the Bartleby guideline, the solution of the first 3 subparts is only provided. 85th Percentil...

Q: What is the important part of drainage system?

A: Solution-  The most essential aspect of an irrigation purposes is adequate absorption and drainage s...

Q: A continuous beam is loaded as shown 18. Which of the following gives the fixed end moment AB in kN-...

A:

Q: A column in a building is subjected to a compressive load from the following sources: 10 kips from d...

A: Given, Loading conditions  ASD design 

Q: 3. A square footing that carries an axial load of 150000kg has its bottom resting on a ground water ...

A:

Q: A circular aluminum tube of L=600mm is loaded in by compressive forces at its ends. The outside and ...

A: Given: circular Aluminium tube(L) =600mm                        Dia outside(d1) =75mm               ...

Q: Define Footing Depth

A: The part of structure which is present in substructure and takes all the load coming from superstruc...

Q: A wooden block with a density of ei is floating completely submerged at the interface of two liquids...

A: given equation to prove; V3V1=(ρ1-ρ2)(ρ3-ρ2)

Q: In which fluid will a pressure of 680 kPa fırst be achieved? Po = 90 kPa ethyl alcohol p = 773.3 kg/...

A:

Q: Define CONTINUOUS FOOTINGSThe

A: The structural part of the building which takes all the load coming from superstructure is known as ...

Q: F2 =60 w3 = 20 alpha = 21 beta = 24 a = 5 b = 14 C = 7 %3D a. Calculate all support reactions (in lb...

A:

Q: mins. and (p)r-02m.

A:

Q: 2. 1.5 m Determine the resultant force the oil exerts on the semicircular surface AB. The tank has a...

A:

Q: An open tube is attached to a tank as shown. If Liquid X (Water) rises to a height of 800 mm in the ...

A:

Q: A beam ISLB 350, 8 m span, carries a total uniformly distributed load of 280 kN. It is supported on ...

A:

Q: Calculate the chemical shrinkage (cm3/g) for one gram of completely hydrated Portland cement with th...

A: Given, C3S = 65% C2S = 19% C3A = 4% C4AF = 9%

Surveys of public lands

A survey is a method used to determine the relative positions of various objects on the land by measuring the horizontal distances between them. Briefly, a survey is a process of accumulation of data of various details related to land. The main objective of surveying land is to prepare maps to a suitable scale. Various types of maps such as topographical maps, cadastral maps, engineering maps, military maps, contour maps, geological maps, archaeological maps, and so on can be prepared by surveying.